AD 2008-09-24

[Federal Register Volume 73, Number 86 (Friday, May 2, 2008)]
[Rules and Regulations]
[Pages 24143-24145]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: E8-9571]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2008-0267; Directorate Identifier 2008-NM-030-AD; 
Amendment 39-15505; AD 2008-09-24]
RIN 2120-AA64


Airworthiness Directives; Bombardier Model DHC-8-400, DHC-8-401, 
and DHC-8-402 Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for the 
products listed above. This AD results from mandatory continuing 
airworthiness information (MCAI) originated by an aviation authority of 
another country to identify and correct an unsafe condition on an 
aviation product. The MCAI describes the unsafe condition as:

    Bombardier Aerospace has completed a system safety review of the 
aircraft fuel system against fuel tank safety standards introduced 
in Chapter 525 of the Airworthiness Manual through Notice of 
Proposed Amendment (NPA) 2002-043. The identified non-compliances 
were then assessed using Transport Canada Policy Letter No. 525-001, 
to determine if mandatory corrective action is required.
    The assessment showed that it is necessary to introduce Critical 
Design Configuration Control Limitations (CDCCL), in order to 
preserve critical fuel tank system ignition source prevention 
features during configuration changes such as modifications and 
repairs, or during maintenance actions. Failure to preserve critical 
fuel tank system ignition source prevention features could result in 
a fuel tank explosion. * * *

We are issuing this AD to require actions to correct the unsafe 
condition on these products.

DATES: This AD becomes effective June 6, 2008.
    The Director of the Federal Register approved the incorporation by 
reference of certain publications listed in this AD as of June 6, 2008.

ADDRESSES: You may examine the AD docket on the Internet at <a href="http://www.regulations.gov">http://www.regulations.gov</a> or in person at the U.S. Department of 
Transportation, Docket Operations, M-30, West Building Ground Floor, 
Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC.

FOR FURTHER INFORMATION CONTACT: Richard Fiesel, Aerospace Engineer, 
Airframe and Propulsion Branch, ANE-171, FAA, New York Aircraft 
Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, New 
York 11590; telephone (516) 228-7304; fax (516) 794-5531.

SUPPLEMENTARY INFORMATION:

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 to include an AD that would apply to the specified products. 
That NPRM was published in the Federal Register on March 11, 2008 (73 
FR 12907). That NPRM proposed to correct an unsafe condition for the 
specified products. The MCAI states:

    Bombardier Aerospace has completed a system safety review of the 
aircraft fuel system against fuel tank safety standards introduced 
in Chapter 525 of the Airworthiness Manual through Notice of 
Proposed Amendment (NPA) 2002-043. The identified non-compliances 
were then assessed using Transport Canada Policy Letter No. 525-001, 
to determine if mandatory corrective action is required.
    The assessment showed that it is necessary to introduce Critical 
Design Configuration Control Limitations (CDCCL), in order to 
preserve critical fuel tank system ignition source prevention 
features during configuration changes such as modifications and 
repairs, or during maintenance actions. Failure to preserve critical 
fuel tank system ignition source prevention features could result in 
a fuel tank explosion. Revisions have been made to Part 2 
``Airworthiness Limitations Items'' of the Maintenance Requirements 
Manual of the affected models to introduce the required CDCCL.

The corrective action is revising the Airworthiness Limitations Section 
of the Instructions for Continued Airworthiness to include the CDCCL 
data. You may obtain further information by examining the MCAI in the 
AD docket.

Comments

    We gave the public the opportunity to participate in developing 
this AD. We received no comments on the NPRM or on the determination of 
the cost to the public.

Conclusion

    We reviewed the available data and determined that air safety and 
the public interest require adopting the AD as proposed.

Differences Between This AD and the MCAI or Service Information

    We have reviewed the MCAI and related service information and, in 
general, agree with their substance. But we might have found it 
necessary to use different words from those in the MCAI to ensure the 
AD is clear for U.S. operators and is enforceable. In making these 
changes, we do not intend to differ substantively from the information 
provided in the MCAI and related service information.
    We might also have required different actions in this AD from those 
in the MCAI in order to follow our FAA policies. Any such differences 
are highlighted in a NOTE within the AD.

Costs of Compliance

    We estimate that this AD will affect about 45 products of U.S. 
registry. We also estimate that it will take about 1 work-hour per 
product to comply with the basic requirements of this AD. The average 
labor rate is $80 per work-hour. Based on these figures, we estimate 
the cost of this AD to the U.S. operators to be $3,600, or $80 per 
product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more

[[Page 24144]]

detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify this AD:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this AD and placed it in the AD docket.

Examining the AD Docket

    You may examine the AD docket on the Internet at <a href="http://www.regulations.gov">http://www.regulations.gov</a>; or in person at the Docket Operations office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains the NPRM, the regulatory evaluation, 
any comments received, and other information. The street address for 
the Docket Operations office (telephone (800) 647-5527) is in the 
ADDRESSES section. Comments will be available in the AD docket shortly 
after receipt.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

0
Accordingly, under the authority delegated to me by the Administrator, 
the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new AD:

2008-09-24 Bombardier, Inc. (Formerly de Havilland, Inc.): Amendment 
39-15505. Docket No. FAA-2008-0267; Directorate Identifier 2008-NM-
030-AD.

Effective Date

    (a) This airworthiness directive (AD) becomes effective June 6, 
2008.

Affected ADs

    (b) None.

Applicability

    (c) This AD applies to all Bombardier Model DHC-8-400, DHC-8-
401, and DHC-8-402 airplanes, certificated in any category, all 
serial numbers.

Subject

    (d) Air Transport Association (ATA) of America Code 28: Fuel.

Reason

    (e) The mandatory continuing airworthiness information (MCAI) 
states:

    Bombardier Aerospace has completed a system safety review of the 
aircraft fuel system against fuel tank safety standards introduced 
in Chapter 525 of the Airworthiness Manual through Notice of 
Proposed Amendment (NPA) 2002-043. The identified non-compliances 
were then assessed using Transport Canada Policy Letter No. 525-001, 
to determine if mandatory corrective action is required.
    The assessment showed that it is necessary to introduce Critical 
Design Configuration Control Limitations (CDCCL), in order to 
preserve critical fuel tank system ignition source prevention 
features during configuration changes such as modifications and 
repairs, or during maintenance actions. Failure to preserve critical 
fuel tank system ignition source prevention features could result in 
a fuel tank explosion. Revisions have been made to Part 2 
``Airworthiness Limitations Items'' of the Maintenance Requirements 
Manual of the affected models to introduce the required CDCCL.

The corrective action is revising the Airworthiness Limitations 
Section (ALS) of the Instructions for Continued Airworthiness to 
include the CDCCL data.

Actions and Compliance

    (f) Unless already done, do the following actions.
    (1) For all airplanes: Within 60 days after the effective date 
of this AD, or before December 16, 2008, whichever occurs first, 
revise the ALS of the Instructions for Continued Airworthiness to 
incorporate the CDCCLs specified in Dash 8 Q400 (Bombardier) 
Temporary Revisions (TRs) ALI-55, dated April 19, 2006; and ALI-56, 
dated April 19, 2006; to Part 2, ``Airworthiness Limitations 
Items,'' of the Bombardier Dash 8 Q400 Maintenance Requirements 
Manual (MRM) PSM 1-84-7.

    Note 1: The actions required by paragraph (f)(1) of this AD may 
be done by inserting a copy of the applicable TR into the 
maintenance requirements manual. When the TR has been included in 
the general revision of the maintenance program, the general 
revision may be inserted into the maintenance requirements manual, 
provided the relevant information in the general revision is 
identical to that in the applicable TR, and the temporary revision 
may be removed.

    (2) After accomplishing the actions specified in paragraph 
(f)(1) of this AD, no alternative CDCCLs may be used unless the 
CDCCLs are part of a later revision of Part 2, Revision 4, dated 
October 30, 2003, of the Bombardier Dash 8 Q400 MRM PSM 1-84-7, 
Revision 4, that is approved by the Manager, New York Aircraft 
Certification Office (ACO), FAA, or Transport Canada Civil Aviation 
(or its delegated agent); or unless the CDCCLs are approved as an 
alternative method of compliance (AMOC) in accordance with the 
procedures specified in paragraph (g)(1) of this AD.

FAA AD Differences

    Note 2: This AD differs from the MCAI and/or service information 
as follows: No differences.

Other FAA AD Provisions

    (g) The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York Aircraft Certification Office, FAA, has the authority to 
approve AMOCs for this AD, if requested using the procedures found 
in 14 CFR 39.19. Send information to ATTN: Richard Fiesel, Aerospace 
Engineer, Airframe and Propulsion Branch, ANE-171, FAA, New York 
Aircraft Certification Office, 1600 Stewart Avenue, Suite 410, 
Westbury, New York 11590; telephone (516) 228-7304; fax (516) 794-
5531. Before using any approved AMOC on any airplane to which the 
AMOC applies, notify your appropriate principal inspector (PI) in 
the FAA Flight Standards District Office (FSDO), or lacking a PI, 
your local FSDO.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.
    (3) Reporting Requirements: For any reporting requirement in 
this AD, under the provisions of the Paperwork Reduction Act, the 
Office of Management and Budget (OMB) has approved the information 
collection requirements and has assigned OMB Control Number 2120-
0056.

Related Information

    (h) Refer to MCAI Canadian Airworthiness Directive CF-2008-06, 
dated January 15,

[[Page 24145]]

2008; and Bombardier TRs ALI-55 and ALI-56, both dated April 19, 
2006; for related information.

Material Incorporated by Reference

    (i) You must use Dash 8 Q400 (Bombardier) Temporary Revision 
ALI-55, dated April 19, 2006, to Part 2, ``Airworthiness Limitations 
Items,'' of the Bombardier Dash 8 Q400 Maintenance Requirements 
Manual PSM 1-84-7; and Dash 8 Q400 (Bombardier) Temporary Revision 
ALI-56, dated April 19, 2006, to Part 2, ``Airworthiness Limitations 
Items,'' of the Bombardier Dash 8 Q400 Maintenance Requirements 
Manual PSM 1-84-7; to do the actions required by this AD, unless the 
AD specifies otherwise.
    (1) The Director of the Federal Register approved the 
incorporation by reference of this service information under 5 
U.S.C. 552(a) and 1 CFR part 51.
    (2) For service information identified in this AD, contact 
Bombardier, Inc., Bombardier Regional Aircraft Division, 123 Garratt 
Boulevard, Downsview, Ontario M3K 1Y5, Canada.
    (3) You may review copies at the FAA, Transport Airplane 
Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the 
National Archives and Records Administration (NARA). For information 
on the availability of this material at NARA, call (202) 741-6030, 
or go to: <a href="http://www.archives.gov/federal-register/cfr/ibr-locations.html">http://www.archives.gov/federal-register/cfr/ibr-locations.html</a>.

    Issued in Renton, Washington, on April 24, 2008.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
 [FR Doc. E8-9571 Filed 5-1-08; 8:45 am]
BILLING CODE 4910-13-P