AD Amdt-39-9787

[Federal Register Volume 61, Number 203 (Friday, October 18, 1996)]
[Rules and Regulations]
[Pages 54331-54332]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 96-26720]



========================================================================
Rules and Regulations
                                                Federal Register
________________________________________________________________________

This section of the FEDERAL REGISTER contains regulatory documents 
having general applicability and legal effect, most of which are keyed 
to and codified in the Code of Federal Regulations, which is published 
under 50 titles pursuant to 44 U.S.C. 1510.

The Code of Federal Regulations is sold by the Superintendent of Documents. 
Prices of new books are listed in the first FEDERAL REGISTER issue of each 
week.

========================================================================


Federal Register / Vol. 61, No. 203 / Friday, October 18, 1996 / 
Rules and Regulations

[[Page 54331]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. 96-NM-122-AD; Amendment 39-9787; AD 96-21-10]
RIN 2120-AA64


Airworthiness Directives; Short Brothers Model SD3-60 SHERPA 
Series Airplanes

AGENCY: Federal Aviation Administration, DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: This amendment adopts a new airworthiness directive (AD), 
applicable to all Short Brothers Model SD3-60 SHERPA series airplanes, 
that requires revising the Airplane Flight Manual (AFM) to provide the 
flight crew with recognition cues for, and procedures for exiting from, 
severe icing conditions, and to limit or prohibit the use of various 
flight control devices. This amendment is prompted by results of a 
review of the requirements for certification of the airplane in icing 
conditions, new information on the icing environment, and icing data 
provided currently to the flight crews. The actions specified by this 
AD are intended to minimize the potential hazards associated with 
operating the airplane in severe icing conditions by providing more 
clearly defined procedures and limitations associated with such 
conditions.

EFFECTIVE DATE: November 22, 1996.

ADDRESSES: Information pertaining to this rulemaking action may be 
examined at the Federal Aviation Administration (FAA), Transport 
Airplane Directorate, Rules Docket, 1601 Lind Avenue, SW., Renton, 
Washington.

FOR FURTHER INFORMATION CONTACT: Greg Dunn, Aerospace Engineer, 
Standardization Branch, ANM-113, FAA, Transport Airplane Directorate, 
1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (206) 
227-2799; fax (206) 227-1149.

SUPPLEMENTARY INFORMATION: A proposal to amend part 39 of the Federal 
Aviation Regulations (14 CFR part 39) to include an airworthiness 
directive (AD) that is applicable to all Short Brothers Model SD3-60 
SHERPA series airplanes was published in the Federal Register on July 
12, 1996 (61 FR 36667). That action proposed to require revising the 
airplane flight manual (AFM) to provide the flight crew with 
recognition cues for, and procedures for exiting from, severe icing 
conditions, and to limit or prohibit the use of various flight control 
devices.
    Interested persons have been afforded an opportunity to participate 
in the making of this amendment. No comments were submitted in response 
to the proposal or the FAA's determination of the cost to the public.

Conclusion

    The FAA has determined that air safety and the public interest 
require the adoption of the rule as proposed.

Cost Impact

    The FAA estimates that 20 Short Brothers Model SD3-60 SHERPA series 
airplanes of U.S. registry will be affected by this AD, that it will 
take approximately 1 work hour per airplane to accomplish the required 
AFM revision, and that the average labor rate is $60 per work hour. 
Based on these figures, the cost impact of the AD on U.S. operators is 
estimated to be $1,200, or $60 per airplane.
    The cost impact figure discussed above is based on assumptions that 
no operator has yet accomplished any of the requirements of this AD 
action, and that no operator would accomplish those actions in the 
future if this AD were not adopted.

Regulatory Impact

    The regulations adopted herein will not have substantial direct 
effects on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government. Therefore, in 
accordance with Executive Order 12612, it is determined that this final 
rule does not have sufficient federalism implications to warrant the 
preparation of a Federalism Assessment.
    For the reasons discussed above, I certify that this action (1) is 
not a ``significant regulatory action'' under Executive Order 12866; 
(2) is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979); and (3) will not have a 
significant economic impact, positive or negative, on a substantial 
number of small entities under the criteria of the Regulatory 
Flexibility Act. A final evaluation has been prepared for this action 
and it is contained in the Rules Docket. A copy of it may be obtained 
from the Rules Docket at the location provided under the caption 
ADDRESSES.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Safety.

Adoption of the Amendment

    Accordingly, pursuant to the authority delegated to me by the 
Administrator, the Federal Aviation Administration amends part 39 of 
the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec. 39.13  [Amended]

    2. Section 39.13 is amended by adding the following new 
airworthiness directive:

96-21-10  Short Brothers, PLC: Amendment 39-9787. Docket 96-NM-122-
AD.

    Applicability: All Model SD3-60 SHERPA series airplanes, 
certificated in any category.

    Note 1: This AD applies to each airplane identified in the 
preceding applicability provision, regardless of whether it has been 
modified, altered, or repaired in the area subject to the 
requirements of this AD. For airplanes that have been modified, 
altered, or repaired so that the performance of the requirements of 
this AD is affected, the owner/operator must request approval for an 
alternative method of compliance in accordance with paragraph (b) of 
this AD. The request should include an assessment of the effect of 
the modification, alteration, or repair on the unsafe condition 
addressed by this AD; and, if the unsafe condition has not been 
eliminated, the request should include specific proposed actions to 
address it.


[[Page 54332]]


    Compliance: Required as indicated, unless accomplished 
previously.
    To minimize the potential hazards associated with operating the 
airplane in severe icing conditions by providing more clearly 
defined procedures and limitations associated with such conditions, 
accomplish the following:
    (a) Within 30 days after the effective date of this AD, 
accomplish the requirements of paragraphs (a)(1) and (a)(2) of this 
AD.

    Note 2: Operators must initiate action to notify and ensure that 
flight crewmembers are apprised of this change.

    (1) Revise the FAA-approved Airplane Flight Manual (AFM) by 
incorporating the following into the Limitations Section of the AFM. 
This may be accomplished by inserting a copy of this AD in the AFM.

``WARNING

    Severe icing may result from environmental conditions outside of 
those for which the airplane is certificated. Flight in freezing 
rain, freezing drizzle, or mixed icing conditions (supercooled 
liquid water and ice crystals) may result in ice build-up on 
protected surfaces exceeding the capability of the ice protection 
system, or may result in ice forming aft of the protected surfaces. 
This ice may not be shed using the ice protection systems, and may 
seriously degrade the performance and controllability of the 
airplane.
    <bullet> During flight, severe icing conditions that exceed 
those for which the airplane is certificated shall be determined by 
the following visual cues. If one or more of these visual cues 
exists, immediately request priority handling from Air Traffic 
Control to facilitate a route or an altitude change to exit the 
icing conditions.

-- Unusually extensive ice accreted on the airframe in areas not 
normally observed to collect ice.
-- Accumulation of ice on the lower surface of the wing aft of the 
protected area.
-- Accumulation of ice on the propeller spinner farther aft than 
normally observed.

    <bullet> Since the autopilot may mask tactile cues that indicate 
adverse changes in handling characteristics, use of the autopilot is 
prohibited when any of the visual cues specified above exist, or 
when unusual lateral trim requirements or autopilot trim warnings 
are encountered while the airplane is in icing conditions.
    <bullet> All icing detection lights must be operative prior to 
flight into icing conditions at night. [NOTE: This supersedes any 
relief provided by the Master Minimum Equipment List (MMEL).]''
    (2) Revise the FAA-approved AFM by incorporating the following 
into the Procedures Section of the AFM. This may be accomplished by 
inserting a copy of this AD in the AFM.

``THE FOLLOWING WEATHER CONDITIONS MAY BE CONDUCIVE TO SEVERE IN-FLIGHT 
ICING

    <bullet> Visible rain at temperatures below 0 degrees Celsius 
ambient air temperature.
    <bullet> Droplets that splash or splatter on impact at 
temperatures below 0 degrees Celsius ambient air temperature.

PROCEDURES FOR EXITING THE SEVERE ICING ENVIRONMENT

    These procedures are applicable to all flight phases from 
takeoff to landing. Monitor the ambient air temperature. While 
severe icing may form at temperatures as cold as -18 degrees 
Celsius, increased vigilance is warranted at temperatures around 
freezing with visible moisture present. If the visual cues specified 
in the Limitations Section of the AFM for identifying severe icing 
conditions are observed, accomplish the following:
    <bullet> Immediately request priority handling from Air Traffic 
Control to facilitate a route or an altitude change to exit the 
severe icing conditions in order to avoid extended exposure to 
flight conditions more severe than those for which the airplane has 
been certificated.
    <bullet> Avoid abrupt and excessive maneuvering that may 
exacerbate control difficulties.
    <bullet> Do not engage the autopilot.
    <bullet> If the autopilot is engaged, hold the control wheel 
firmly and disengage the autopilot.
    <bullet> If an unusual roll response or uncommanded roll control 
movement is observed, reduce the angle-of-attack.
    <bullet> Do not extend flaps during extended operation in icing 
conditions. Operation with flaps extended can result in a reduced 
wing angle-of- attack, with the possibility of ice forming on the 
upper surface further aft on the wing than normal, possibly aft of 
the protected area.
    <bullet> If the flaps are extended, do not retract them until 
the airframe is clear of ice.
    <bullet> Report these weather conditions to Air Traffic 
Control.''
    (b) An alternative method of compliance or adjustment of the 
compliance time that provides an acceptable level of safety may be 
used if approved by the Manager, Standardization Branch, ANM-113, 
FAA, Transport Airplane Directorate. Operators shall submit their 
requests through an appropriate FAA Principal Maintenance Inspector, 
who may add comments and then send it to the Manager, 
Standardization Branch, ANM-113.

    Note 3: Information concerning the existence of approved 
alternative methods of compliance with this AD, if any, may be 
obtained from the Standardization Branch, ANM-113.

    (c) Special flight permits may be issued in accordance with 
sections 21.197 and 21.199 of the Federal Aviation Regulations (14 
CFR 21.197 and 21.199) to operate the airplane to a location where 
the requirements of this AD can be accomplished.
    (d) This amendment becomes effective on November 22, 1996.

    Issued in Renton, Washington, on October 10, 1996.
S.R. Miller,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 96-26720 Filed 10-17-96; 8:45 am]
BILLING CODE 4910-13-P