AD 2020-03-23
Applicability
| Type | Manufacturer | Model | Details |
|---|---|---|---|
| aircraft | Bombardier Inc. | CL-600-2B19 (Regional Jet Series 100) | Airworthiness Directives; Bombardier, Inc., Airplanes |
| aircraft | Bombardier Inc. | CL-600-2B19 (Regional Jet Series 440) | Airworthiness Directives; Bombardier, Inc., Airplanes |
Unsafe Condition
damage to the insulation sleeve of the generator power cables that can potentially cause a short circuit, arcing, and a malfunction of one or both main generators.
AI-generated summary from the source AD text. Verify against the official source before acting.
Required Actions
visually inspect the generator power cables and wire strands for damage, install protective conduits and edging grommets, and do all applicable corrective actions, in accordance with the Accomplishment Instructions of Bombardier Service Bulletin 601R-24-131, dated June 28, 2012. Do all applicable corrective actions before further flight.
AI-generated summary from the source AD text. Verify against the official source before acting.
Compliance Time
Within 18 months after the effective date of this AD
AI-generated summary from the source AD text. Verify against the official source before acting.
Affected Aircraft
Bombardier, Inc., Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes, certificated in any category, as identified in Bombardier Service Bulletin 601R-24-131, dated June 28, 2012.
AI-generated summary from the source AD text. Verify against the official source before acting.
Federal Register Abstract
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier, Inc., Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. This AD was prompted by a report that a fouling condition was found between the generator power cables and the support brackets of the auxiliary-aft fuel tank during production. This AD requires a visual inspection of the generator power cables for damage, installation of protective conduits and edging grommets, and applicable corrective actions. The FAA is issuing this AD to address the unsafe condition on these products.
Applicability Source Text
Show captured applicability text from the source AD
(c) Applicability
This AD applies to Bombardier, Inc., Model CL-600-2B19 (Regional
Jet Series 100 & 440) airplanes, certificated in any category, as
identified in Bombardier Service Bulletin 601R-24-131, dated June
28, 2012.
Document Text
Show stored source text (verify against official source)
[Federal Register Volume 85, Number 39 (Thursday, February 27, 2020)]
[Rules and Regulations]
[Pages 11284-11286]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2020-03934]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2019-0877; Product Identifier 2019-NM-146-AD; Amendment
39-19847; AD 2020-03-23]
RIN 2120-AA64
Airworthiness Directives; Bombardier, Inc., Airplanes
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: The FAA is adopting a new airworthiness directive (AD) for
certain Bombardier, Inc., Model CL-600-2B19 (Regional Jet Series 100 &
440) airplanes. This AD was prompted by a report that a fouling
condition was found between the generator power cables and the support
brackets of the auxiliary-aft fuel tank during production. This AD
requires a visual inspection of the generator power cables for damage,
installation of protective conduits and edging grommets, and applicable
corrective actions. The FAA is issuing this AD to address the unsafe
condition on these products.
DATES: This AD is effective April 2, 2020.
The Director of the Federal Register approved the incorporation by
reference of a certain publication listed in this AD as of April 2,
2020.
ADDRESSES: For service information identified in this final rule,
contact Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval,
Qu[eacute]bec H4S 1Y9, Canada; Widebody Customer Response Center North
America toll-free telephone 1-866-538-1247 or direct-dial telephone 1-
514-855-2999; fax 514-855-7401; email <a href="/cdn-cgi/l/email-protection#c4a5a7eabdb1a884a5a1b6abeaa6aba9a6a5b6a0ada1b6eaa7aba9"><span class="__cf_email__" data-cfemail="1d7c7e336468715d7c786f72337f72707f7c6f7974786f337e7270">[email protected]</span></a>;
internet <a href="http://www.bombardier.com">http://www.bombardier.com</a>. You may view this service
information at the FAA, Transport Standards Branch, 2200 South 216th
St., Des Moines, WA. For information on the availability of this
material at the FAA, call 206-231-3195. It is also available on the
internet at <a href="https://www.regulations.gov">https://www.regulations.gov</a> by searching for and locating
Docket No. FAA-2019-0877.
Examining the AD Docket
You may examine the AD docket on the internet at <a href="https://www.regulations.gov">https://www.regulations.gov</a> by searching for and locating Docket No. FAA-2019-
0877; or in person at Docket Operations between 9 a.m. and 5 p.m.,
Monday through Friday, except Federal holidays. The AD docket contains
this final rule, the regulatory evaluation, any comments received, and
other information. The address for Docket Operations is U.S. Department
of Transportation, Docket Operations, M-30, West Building Ground Floor,
Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590.
FOR FURTHER INFORMATION CONTACT: Thomas Niczky, Aerospace Engineer,
Avionics and Electrical Systems Services Section, FAA, New York ACO
Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone
516-228-7347; fax 516-794-5531; email <a href="/cdn-cgi/l/email-protection#ab9286caddd886c5d2cac8c486c8c4d8ebcdcaca85ccc4dd"><span class="__cf_email__" data-cfemail="30091d5146431d5e4951535f1d535f43705651511e575f46">[email protected]</span></a>.
SUPPLEMENTARY INFORMATION:
Discussion
Transport Canada Civil Aviation (TCCA), which is the aviation
authority for Canada, has issued Canadian AD CF-2019-22, dated May 27,
2019
[[Page 11285]]
(``Canadian AD CF-2019-22'') (also referred to as the Mandatory
Continuing Airworthiness Information, or ``the MCAI''), to correct an
unsafe condition for certain Bombardier, Inc., Model CL-600-2B19
(Regional Jet Series 100 & 440) airplanes. You may examine the MCAI in
the AD docket on the internet at <a href="https://www.regulations.gov">https://www.regulations.gov</a> by
searching for and locating Docket No. FAA-2019-0877.
The FAA issued a notice of proposed rulemaking (NPRM) to amend 14
CFR part 39 by adding an AD that would apply to certain Bombardier,
Inc., Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. The
NPRM published in the Federal Register on December 2, 2019 (84 FR
65935). The NPRM was prompted by a report that a fouling condition was
found between the generator power cables and the support brackets of
the auxiliary-aft fuel tank during production. The NPRM proposed to
require a visual inspection of the generator power cables for damage,
installation of protective conduits and edging grommets, and applicable
corrective actions. The FAA is issuing this AD to address damage to the
insulation sleeve of the generator power cables that can potentially
cause a short circuit, arcing, and a malfunction of one or both main
generators. See the MCAI for additional background information.
Comments
The FAA gave the public the opportunity to participate in
developing this final rule. The FAA received no comments on the NPRM or
on the determination of the cost to the public.
Conclusion
The FAA reviewed the relevant data and determined that air safety
and the public interest require adopting this final rule as proposed,
except for minor editorial changes. The FAA has determined that these
minor changes:
<bullet> Are consistent with the intent that was proposed in the
NPRM for addressing the unsafe condition; and
<bullet> Do not add any additional burden upon the public than was
already proposed in the NPRM.
Related Service Information Under 1 CFR Part 51
Bombardier has issued Service Bulletin 601R-24-131, dated June 28,
2012. This service information describes procedures for visual
inspection of the generator power cables for damage, installation of
protective insulation and edging grommets, and applicable corrective
actions. Corrective actions include repair. This service information is
reasonably available because the interested parties have access to it
through their normal course of business or by the means identified in
the ADDRESSES section.
Costs of Compliance
The FAA estimates that this AD affects 9 airplanes of U.S.
registry. The FAA estimates the following costs to comply with this AD:
Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
Cost per Cost on U.S.
Labor cost Parts cost product operators
----------------------------------------------------------------------------------------------------------------
22 work-hours x $85 per hour = $1,870........................ $524 $2,394 $21,546
----------------------------------------------------------------------------------------------------------------
The FAA has received no definitive data that would enable the
agency to provide cost estimates for the on-condition actions specified
in this AD.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
This AD will not have federalism implications under Executive Order
13132. This AD will not have a substantial direct effect on the States,
on the relationship between the national government and the States, or
on the distribution of power and responsibilities among the various
levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Will not affect intrastate aviation in Alaska, and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive (AD):
2020-03-23 Bombardier, Inc.: Amendment 39-19847; Docket No. FAA-
2019-0877; Product Identifier 2019-NM-146-AD.
(a) Effective Date
This AD is effective April 2, 2020.
(b) Affected ADs
None.
(c) Applicability
This AD applies to Bombardier, Inc., Model CL-600-2B19 (Regional
Jet Series 100 & 440) airplanes, certificated in any category, as
identified in Bombardier Service Bulletin 601R-24-131, dated June
28, 2012.
(d) Subject
Air Transport Association (ATA) of America Code 24, Electrical
power.
(e) Reason
This AD was prompted by a report that a fouling condition was
found between the generator power cables and the support brackets of
the auxiliary-aft fuel tank during production. The FAA is issuing
this AD to address damage to the insulation sleeve of the generator
power cables that can potentially cause a short circuit, arcing, and
a malfunction of one or both main generators.
[[Page 11286]]
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Required Actions
Within 18 months after the effective date of this AD, visually
inspect the generator power cables and wire strands for damage,
install protective conduits and edging grommets, and do all
applicable corrective actions, in accordance with the Accomplishment
Instructions of Bombardier Service Bulletin 601R-24-131, dated June
28, 2012. Do all applicable corrective actions before further
flight.
(h) Other FAA AD Provisions
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, New
York ACO Branch, FAA, has the authority to approve AMOCs for this
AD, if requested using the procedures found in 14 CFR 39.19. In
accordance with 14 CFR 39.19, send your request to your principal
inspector or local Flight Standards District Office, as appropriate.
If sending information directly to the manager of the certification
office, send it to ATTN: Program Manager, Continuing Operational
Safety, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410,
Westbury, NY 11590; telephone 516-228-7300; fax 516-794-5531. Before
using any approved AMOC, notify your appropriate principal
inspector, or lacking a principal inspector, the manager of the
local flight standards district office/certificate holding district
office.
(2) Contacting the Manufacturer: For any requirement in this AD
to obtain instructions from a manufacturer, the instructions must be
accomplished using a method approved by the Manager, New York ACO
Branch, FAA; or Transport Canada Civil Aviation (TCCA); or
Bombardier, Inc.'s TCCA Design Approval Organization (DAO). If
approved by the DAO, the approval must include the DAO-authorized
signature.
(i) Related Information
(1) Refer to Mandatory Continuing Airworthiness Information
(MCAI) Canadian AD CF-2019-22, dated May 27, 2019, for related
information. This MCAI may be found in the AD docket on the internet
at <a href="https://www.regulations.gov">https://www.regulations.gov</a> by searching for and locating Docket
No. FAA-2019-0877.
(2) For more information about this AD, contact Thomas Niczky,
Aerospace Engineer, Avionics and Electrical Systems Services
Section, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410,
Westbury, NY 11590; telephone 516-228-7347; fax 516-794-5531; email
<a href="/cdn-cgi/l/email-protection#9ba2b6faede8b6f5e2faf8f4b6f8f4e8dbfdfafab5fcf4ed"><span class="__cf_email__" data-cfemail="71485c1007025c1f0810121e5c121e02311710105f161e07">[email protected]</span></a>.
(j) Material Incorporated by Reference
(1) The Director of the Federal Register approved the
incorporation by reference (IBR) of the service information listed
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this service information as applicable to do
the actions required by this AD, unless this AD specifies otherwise.
(i) Bombardier Service Bulletin 601R-24-131, dated June 28,
2012.
(ii) [Reserved]
(3) For service information identified in this AD, contact
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval,
Qu[eacute]bec H4S 1Y9, Canada; Widebody Customer Response Center
North America toll-free telephone 1-866-538-1247 or direct-dial
telephone 1-514-855-2999; fax 514-855-7401; email
<a href="/cdn-cgi/l/email-protection#365755184f435a76575344591854595b545744525f53441855595b"><span class="__cf_email__" data-cfemail="1a7b7934636f765a7b7f687534787577787b687e737f6834797577">[email protected]</span></a>; internet <a href="http://www.bombardier.com">http://www.bombardier.com</a>.
(4) You may view this service information at the FAA, Transport
Standards Branch, 2200 South 216th St., Des Moines, WA. For
information on the availability of this material at the FAA, call
206-231-3195.
(5) You may view this service information that is incorporated
by reference at the National Archives and Records Administration
(NARA). For information on the availability of this material at
NARA, email <a href="/cdn-cgi/l/email-protection#caacafaeb8afade4a6afadaba68aa4abb8abe4ada5bc"><span class="__cf_email__" data-cfemail="b9dfdcddcbdcde97d5dcded8d5f9d7d8cbd897ded6cf">[email protected]</span></a>, or go to: <a href="https://www.archives.gov/federal-register/cfr/ibr-locations.html">https://www.archives.gov/federal-register/cfr/ibr-locations.html</a>.
Issued on February 14, 2020.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification
Service.
[FR Doc. 2020-03934 Filed 2-26-20; 8:45 am]
BILLING CODE 4910-13-P
Source: Official FAA Source ↗
Retrieved: Apr 4, 2026
Rights: U.S. Government Public Domain
This site is not affiliated with or endorsed by the FAA. Always verify with official sources.