AD 2015-12-05

[Federal Register Volume 80, Number 115 (Tuesday, June 16, 2015)]
[Rules and Regulations]
[Pages 34249-34252]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2015-14283]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2014-0618; Directorate Identifier 2012-NM-171-AD; 
Amendment 39-18178; AD 2015-12-05]
RIN 2120-AA64


Airworthiness Directives; Airbus Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are superseding Airworthiness Directive (AD) 2008-06-18 for 
all Airbus Model A300 B4-600, B4-600R, and F4-600R series airplanes, 
and Model A300 C4-605R Variant F airplanes (collectively called Model 
A300-600 series airplanes); and Model A300 series airplanes. AD 2008-
06-18 required repetitive inspections for any cracking of the wing 
lower skin panel and associated internal support structure, and if 
necessary, corrective actions such as modifying the lower panel inboard 
of rib 9 aft of the rear spar and repairing cracks. This new AD 
continues to require actions required by AD 2008-06-18, and reduces 
certain compliance times. This AD was prompted by a report that 
information from an analysis and a fleet survey shows a need for 
reduced compliance times and intervals. We are issuing this AD to 
detect and correct cracking, which could lead to reduced structural 
integrity of the airplane.

DATES: This AD becomes effective July 21, 2015.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of July 21, 
2015.
    The Director of the Federal Register approved the incorporation by 
reference of certain other publications listed in this AD as of April 
23, 2008 (73 FR 14670, March 19, 2008).

ADDRESSES: You may examine the AD docket on the Internet at <a href="http://www.regulations.gov/#!docketDetail">http://www.regulations.gov/#!docketDetail</a>;D=FAA-2014-0618; or in person at the 
Docket Management Facility, U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC.
    For service information identified in this AD, contact Airbus SAS 
Airworthiness Office- EAW, 1 Rond Point Maurice Bellonte, 31707 Blagnac 
Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 93 44 51; 
email <a href="/cdn-cgi/l/email-protection#ee8f8d8d819b809ac08f879c99819c9a86c38b8f9dae8f879c8c9b9dc08d8183"><span class="__cf_email__" data-cfemail="016062626e746f752f606873766e7375692c646072416068736374722f626e6c">[email&#160;protected]</span></a>; Internet <a href="http://www.airbus.com">http://www.airbus.com</a>. 
You may view this referenced service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information 
on the availability of this material at the FAA, call 425-227-1221. It 
is also available on the Internet at <a href="http://www.regulations.gov">http://www.regulations.gov</a> by 
searching for and locating Docket No. FAA-2014-0618.

FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue SW., Renton, WA 98057-3356; telephone 425-227-2125; 
fax 425-227-1149.

SUPPLEMENTARY INFORMATION:

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 to supersede AD 2008-06-18, Amendment 39-15430 (73 FR 14670, 
March 19, 2008). AD 2008-06-18 applied to all Airbus Model A300 B4-600, 
B4-600R, and F4-600R series airplanes, and Model A300 C4-605R Variant F 
airplanes (collectively called Model A300-600 series airplanes); and 
Model A300 series airplanes. The NPRM published in the Federal Register 
on September 3, 2014 (79 FR 52263). The NPRM proposed to continue to 
require repetitive inspections for any cracking of the wing lower skin 
panel and associated internal support structure, and if necessary, 
corrective actions such as modifying the lower panel inboard of rib 9 
aft of the rear spar and repairing cracks. The NPRM also proposed to 
reduce some compliance times.
    The European Aviation Safety Agency (EASA), which is the Technical 
Agent for the Member States of the European Union, has issued EASA 
Airworthiness Directive 2012-0203, dated October 1, 2012 (referred to 
after this as the Mandatory Continuing Airworthiness Information, or 
``the MCAI''), to correct an unsafe condition on all Airbus Model A300 
B4-600, B4-600R, and F4-600R series airplanes, and Model A300 C4-605R 
Variant F airplanes (collectively called Model A300-600 series 
airplanes); and Model A300 series airplanes. The MCAI states:

    During routine maintenance, cracks were found in the wing bottom 
skin and in the associated internal support structure on an A300 
aeroplane aft of the rear spar and inboard of rib 9. Initially, 
cracks were found in the skin only, starting from a fastener close 
to the forward outboard corner of access panel 575FB/675FB. 
Subsequently, cases were reported of cracks being found in the skin 
support strap and the stiffener.
    This condition, if not detected and corrected, could affect the 
structural integrity of the aeroplane.
    To address this unsafe condition, EASA issued AD 2006-0282 
[<a href="http://ad.easa.europa.eu/ad/2006-0282">http://ad.easa.europa.eu/ad/2006-0282</a>] [which corresponds with FAA 
AD 2008-06-18, Amendment 39-15430 (73 FR 14670, March 19, 2008)] to 
require repetitive inspections of the wing lower skin panel and 
associated internal support structure aft of the rear spar and 
inboard of rib 9.
    Since that [EASA] AD was issued, the results of a fleet survey 
and updated Fatigue and Damage Tolerance analysis, which were 
performed in order to substantiate the second A300 and A300-600 
Extended Service Goal (ESG2) exercise, revealed that the inspection 
threshold and interval had to be reduced to allow timely detection 
of cracks and the accomplishment of an applicable corrective action.
    Prompted by these findings, Airbus issued Revision 05 of Airbus 
Service Bulletin (SB) A300-57-0177 and Revision 07 of Airbus SB 
A300-57-6029.
    For the reasons described above, this [EASA] AD retains the 
requirements of EASA AD 2006-0282, which is superseded, but requires 
the accomplishment of those actions within reduced thresholds and 
intervals.

    You may examine the MCAI in the AD docket on the Internet at <a href="http://www.regulations.gov/#!documentDetail">http://www.regulations.gov/#!documentDetail</a>;D=FAA-2014-0618-0002.

Comments

    We gave the public the opportunity to participate in developing 
this AD. The following presents the comment received on the NPRM (79 FR 
52263, September 3, 2014) and the FAA's response to each comment.

Request To Revise Method Used To Determine Compliance Times

    United Parcel Service (UPS) requested that the proposed compliance 
times be revised to be less complex. UPS stated that the proposed 
compliance times contain a method known as ``Average Flight Time'' 
(AFT) which results in a variable flight hour limit and adds an 
unnecessary complexity to the threshold table and subsequent inspection 
actions. UPS added that use of the AFT method, along with a lack of 
standard procedures for implementing the AFT method would create 
uncertainty for operators

[[Page 34250]]

and inspectors trying to determine the correct compliance time. UPS 
stated that in review of prior FAA ADs, including AD 98-18-02, that the 
FAA does not concur with the AFT compliance time methodology as ``. . . 
such adjustments may not address the unsafe condition in a timely 
manner'' and ``. . . they (AFT compliance times) do not fit into the AD 
tracking process for operators or for Principle Maintenance Inspectors 
(PMIs) attempting to ascertain compliance with ADs.'' UPS compiled a 
table of fixed compliance times that it suggested would be simpler to 
use instead of the proposed AFT-based compliance times.
    We disagree with the commenter's request to revise the compliance 
times in this AD. In AD 98-18-02, Amendment 39-10718 (63 FR 45689, 
August 27, 1998), and certain other ADs, the required actions referred 
to service information that contained inspection thresholds and 
intervals based on airplane flight cycles only. Therefore, the FAA did 
not agree with the use of the ``average flight time'' (AFT) method to 
adjust the inspection thresholds and intervals, which were based only 
on flight cycles. However, for this AD the compliance times in Airbus 
Service Bulletin A300-57-0177, Revision 05, dated March 23, 2007, and 
Airbus Service Bulletin A300-57-6029, Revision 08, dated April 25, 
2013, have been determined for a combination of flight cycles and 
flight hours for which the AFT methodology is appropriate.
    We acknowledge that a fixed compliance time for a fleet could be 
easier for operators to schedule and record compliance. Therefore, 
under the provisions of paragraph (j)(1) of this AD, we will consider 
requests for approval of an alternative method of compliance (AMOC) if 
a proposal is submitted that is supported by technical data that 
includes fatigue and damage tolerance analysis We have not changed this 
AD in this regard.

Conclusion

    We reviewed the available data, including the comment received, and 
determined that air safety and the public interest require adopting 
this AD as proposed except for minor editorial changes. We have 
determined that these minor changes:
    <bullet> Are consistent with the intent that was proposed in the 
NPRM (79 FR 52263, September 3, 2014) for correcting the unsafe 
condition; and
    <bullet> Do not add any additional burden upon the public than was 
already proposed in the NPRM (79 FR 52263, September 3, 2014).

Related Service Information Under 1 CFR Part 51

    Airbus has issued Service Bulletin A300-57-6029, Revision 08, dated 
April 25, 2013. The service information describes procedures for 
inspecting the wing lower skin panel and associated internal support 
structure aft of the rear spar and inboard of rib 9 and applying 
applicable corrective measures. This service information is reasonably 
available because the interested parties have access to it through 
their normal course of business or by the means identified in the 
ADDRESSES section of this AD.

Costs of Compliance

    We estimate that this AD affects 162 airplanes of U.S. registry.
    The actions that were required by AD 2008-06-18, Amendment 39-15430 
(73 FR 14670, March 19, 2008), and retained in this AD take about 2 
work-hours per product, at an average labor rate of $85 per work-hour. 
Based on these figures, the estimated cost of the actions that were 
required by AD 2008-06-18 is $170 per product.
    We also estimate that it will take about 2 work-hours per product 
to comply with the basic requirements of this AD. The average labor 
rate is $85 per work-hour. Based on these figures, we estimate the cost 
of this AD on U.S. operators to be $27,540, or $170 per product.
    In addition, we estimate that any necessary follow-on actions would 
take about 12 work-hours and require parts costing $10,000, for a cost 
of $11,020 per product. We have no way of determining the number of 
aircraft that might need these actions.

Paperwork Reduction Act

    A federal agency may not conduct or sponsor, and a person is not 
required to respond to, nor shall a person be subject to penalty for 
failure to comply with a collection of information subject to the 
requirements of the Paperwork Reduction Act unless that collection of 
information displays a current valid OMB control number. The control 
number for the collection of information required by this AD is 2120-
0056. The paperwork cost associated with this AD has been detailed in 
the Costs of Compliance section of this document and includes time for 
reviewing instructions, as well as completing and reviewing the 
collection of information. Therefore, all reporting associated with 
this AD is mandatory. Comments concerning the accuracy of this burden 
and suggestions for reducing the burden should be directed to the FAA 
at 800 Independence Ave. SW., Washington, DC 20591, ATTN: Information 
Collection Clearance Officer, AES-200.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

Examining the AD Docket

    You may examine the AD docket on the Internet at <a href="http://www.regulations.gov/#!docketDetail">http://www.regulations.gov/#!docketDetail</a>;D=FAA-2014-0618; or in person at the 
Docket Management Facility between 9 a.m. and 5 p.m., Monday through 
Friday, except Federal holidays. The AD docket contains this AD, the 
regulatory evaluation, any comments received, and other information. 
The street address for the Docket Operations office (telephone 800-647-
5527) is in the ADDRESSES section.

[[Page 34251]]

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by removing Airworthiness Directive (AD) 
2008-06-18, Amendment 39-15430 (73 FR 14670, March 19, 2008), and 
adding the following new AD:

2015-12-05 Airbus: Amendment 39-18178. Docket No. FAA-2014-0618; 
Directorate Identifier 2012-NM-171-AD.

(a) Effective Date

    This AD becomes effective July 21, 2015.

(b) Affected ADs

    This AD replaces AD 2008-06-18, Amendment 39-15430 (73 FR 14670, 
March 19, 2008).

(c) Applicability

    This AD applies to the airplanes identified in paragraphs (c)(1) 
through (c)(5) of this AD, certificated in any category, all 
certified models, all serial numbers.
    (1) Airbus Model A300 B2-1A, B2-1C, B2K-3C, B2-203, B4-2C, B4-
103, and B4-203 airplanes.
    (2) Airbus Model A300 B4-601, B4-603, B4-620, and B4-622 
airplanes.
    (3) Airbus Model A300 B4-605R and B4-622R airplanes.
    (4) Airbus Model A300 F4-605R and F4-622R airplanes.
    (5) Airbus Model A300 C4-605R Variant F airplanes.

(d) Subject

    Air Transport Association (ATA) of America Code 57, Wings.

(e) Reason

    This AD was prompted by a report that information from an 
analysis and a fleet survey shows a need for reduced compliance 
times and intervals. We are issuing this AD to detect and correct 
cracking, which could lead to reduced structural integrity of the 
airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Retained Actions and Compliance Times, with Revised Service 
Information

    This paragraph restates the requirements of paragraph (f) of AD 
2008-06-18, Amendment 39-15430 (73 FR 14670, March 19, 2008), with 
revised service information. Unless already done, do the following 
actions.
    (1) Except as provided by paragraphs (g)(1)(i), (g)(1)(ii), 
(g)(1)(iii), (g)(1)(iv), and (h) of this AD: At the threshold 
specified in paragraph 1.E.(2), ``Accomplishment Timescale,'' of 
Airbus Service Bulletin A300-57-0177, Revision 05, dated March 23, 
2007 (for Model A300 series airplanes); Airbus Service Bulletin 
A300-57-6029, Revision 06, dated March 23, 2007 (for Model A300-600 
series airplanes); or Airbus Service Bulletin A300-57-6029, Revision 
08, dated April 25, 2013 (for Model A300-600 series airplanes); as 
applicable; perform the inspection of the wing lower skin panel and 
associated internal support structure aft of the rear spar and 
inboard of rib 9 and apply applicable corrective measures in 
accordance with Airbus Service Bulletin A300-57-0177, Revision 05, 
dated March 23, 2007 (for Model A300 series airplanes); Airbus 
Service Bulletin A300-57-6029, Revision 06, dated March 23, 2007 
(for Model A300-600 series airplanes); or Airbus Service Bulletin 
A300-57-6029, Revision 08, dated April 25, 2013 (for Model A300-600 
series airplanes); as applicable. All applicable corrective measures 
must be done at the applicable times specified in paragraph 1.E.(2) 
and the Accomplishment Instructions of Airbus Service Bulletin A300-
57-0177, Revision 05, dated March 23, 2007 (for Model A300 series 
airplanes); Airbus Service Bulletin A300-57-6029, Revision 06, dated 
March 23, 2007 (for Model A300-600 series airplanes); or Airbus 
Service Bulletin A300-57-6029, Revision 08, dated April 25, 2013 
(for Model A300-600 series airplanes); as applicable. Accomplishing 
the requirements of paragraph (h) of this AD terminates the 
requirements of this paragraph for Model A300-600 airplanes.
    (i) Where the tables in paragraph 1.E.(2), ``Accomplishment 
Timescale,'' of Airbus Service Bulletin A300-57-0177, Revision 05, 
dated March 23, 2007; and Airbus Service Bulletin A300-57-6029, 
Revision 06, dated March 23, 2007; specify a grace period for doing 
the actions, this AD requires that the actions be done within the 
specified grace period relative to April 23, 2008 (the effective 
date of AD 2008-06-18, Amendment 39-15430 (73 FR 14670, March 19, 
2008)).
    (ii) Where the tables in paragraph 1.E.(2)(e), ``Config 04,'' of 
Airbus Service Bulletin A300-57-0177, Revision 05, dated March 23, 
2007, specify an inspection interval but not an initial threshold, 
this AD requires that the actions be done within the specified 
interval after inspecting in accordance with Table 1A or 1B, as 
applicable, for Configuration 01 airplanes described in the Airbus 
Service Bulletin A300-57-0177, Revision 05, dated March 23, 2007, 
and thereafter at the inspection interval specified in the tables in 
paragraph 1.E.(2)(e), ``Config 04,'' of Airbus Service Bulletin 
A300-57-0177, Revision 05, dated March 23, 2007.
    (iii) Where the tables in paragraph 1.E.(2)(f), ``Config 05,'' 
of Airbus Service Bulletin A300-57-6029, Revision 06, dated March 
23, 2007, specify an inspection interval but not an initial 
threshold, this AD requires that the actions be done within the 
specified interval after inspecting in accordance with Table 1A, or 
1B, as applicable, for Configuration 01 airplanes described in 
Airbus Service Bulletin A300-57-6029, Revision 06, dated March 23, 
2007, and thereafter at the inspection interval specified in the 
tables in paragraph 1.E.(2)(f), ``Config 05,'' of Airbus Service 
Bulletin A300-57-6029, Revision 06, dated March 23, 2007.
    (iv) All crack lengths specified in Airbus Service Bulletin 
A300-57-0177, Revision 05, dated March 23, 2007; and Airbus Service 
Bulletin A300-57-6029, Revision 06, dated March 23, 2007, are 
considered ``not to exceed'' lengths.
    (2) Repeat the inspection at the intervals in, and according to 
the instructions defined in, Airbus Service Bulletin A300-57-0177, 
Revision 05, dated March 23, 2007 (for Model A300 series airplanes); 
Airbus Service Bulletin A300-57-6029, Revision 06, dated March 23, 
2007 (for Model A300-600 series airplanes); or Airbus Service 
Bulletin A300-57-6029, Revision 08, dated April 25, 2013 (for Model 
A300-600 series airplanes); as applicable; except where Airbus 
Service Bulletin A300-57-0177, Revision 05, dated March 23, 2007, 
specifies repetitive inspections for cracking if Airbus Service 
Bulletin A300-57-022 has not been embodied, this AD requires doing 
repetitive inspections for cracking if Airbus Service Bulletin A300-
57-0222 (modification 11178H5410) has not been embodied.
    (3) Report to Airbus the first inspection results, whatever they 
may be, at the applicable time specified in paragraph (g)(3)(i) or 
(g)(3)(ii) of this AD.
    (i) If the inspection was done after April 23, 2008 (the 
effective date of AD 2008-06-18, Amendment 39-15430 (73 FR 14670, 
March 19, 2008)), submit the report within 30 days after the 
inspection.
    (ii) If the inspection was accomplished prior to April 23, 2008 
(the effective date of AD 2008-06-18, Amendment 39-15430 (73 FR 
14670, March 19, 2008)), submit the report within 30 days after 
April 23, 2008.

(h) New Requirement of This AD: New Compliance Times for Model A300-600 
Series Airplanes

    For Model A300-600 series airplanes, do the actions specified in 
paragraphs (h)(1) through (h)(3) of this AD at the applicable times 
specified in those paragraphs.
    (1) Except as provided by paragraphs (h)(1)(i) and (h)(1)(ii) of 
this AD: Within the compliance times specified in Airbus Service 
Bulletin A300-57-6029, Revision 08, dated April 25, 2013, perform 
the inspection of the wing lower skin panels and associated internal 
support structures aft of the rear spar and inboard of rib 9, in 
accordance with the Accomplishment Instructions of Airbus Service 
Bulletin A300-57-6029, Revision 08, dated April 25, 2013. 
Thereafter, repeat these inspections at intervals specified in 
Airbus Service Bulletin A300-57-6029, Revision 08, dated April 25, 
2013. Accomplishment of the actions required by this paragraph 
terminates

[[Page 34252]]

the requirements of paragraph (g) of this AD for Model A300-600 
airplanes.
    (i) Where the tables in paragraph 1.E.(2), ``Accomplishment 
Timescale,'' of Airbus Service Bulletin A300-57-6029, Revision 08, 
dated April 25, 2013, specify a grace period for doing the actions 
for airplanes that have exceeded the thresholds, this AD requires, 
for all airplanes, that the actions be done within the specified 
grace period after the effective date of this AD or before the 
specified thresholds, whichever occurs later.
    (ii) Where Airbus Service Bulletin A300-57-6029, Revision 08, 
dated April 25, 2013, specifies to ``contact Airbus'' before further 
flight, this AD requires repairing using a method approved by the 
Manager, International Branch, ANM-116, Transport Airplane 
Directorate, FAA; or European Aviation Safety Agency (EASA); or 
Airbus's EASA Design Organization Approval (DOA); and accomplishing 
those actions before further flight. If approved by the DOA, the 
approval must include the DOA-authorized signature.
    (2) If, during any inspection as required by paragraph (h)(1) of 
this AD, discrepancies are detected, before next flight, accomplish 
the applicable corrective actions, in accordance with the 
Accomplishment Instructions of Airbus Service Bulletin A300-57-6029, 
Revision 08, dated April 25, 2013.
    (3) Corrective actions, as required by paragraph (h)(2) of this 
AD, do not constitute terminating action for the repetitive 
inspection requirements of paragraph (h)(1) of this AD.

(i) Credit for Previous Actions

    (1) This paragraph provides credit for actions required by 
paragraph (g) of this AD, if those actions were performed before 
April 23, 2008 (the effective date of AD 2008-06-18, Amendment 39-
15430 (73 FR 14670, March 19, 2008)), using the applicable service 
information identified in paragraphs (i)(1)(i) through (i)(1)(iv) of 
this AD, which are not incorporated by reference by this AD.
    (i) Airbus Service Bulletin A300-57-0177, Revision 03, dated May 
29, 2006 (for Model A300 series airplanes).
    (ii) Airbus Service Bulletin A300-57-0177, Revision 04, dated 
January 5, 2007 (for Model A300 series airplanes).
    (iii) Airbus Service Bulletin A300-57-6029, Revision 04, dated 
May 29, 2006 (for Model A300-600 series airplanes).
    (iv) Airbus Service Bulletin A300-57-6029, Revision 05, dated 
October 23, 2006 (for Model A300-600 series airplanes).
    (2) This paragraph provides credit for actions required by 
paragraph (g) or (h) of this AD, if those actions were performed 
before the effective date of this AD, using Airbus Service Bulletin 
A300-57-6029, Revision 07, dated June 6, 2011 (for Model A300-600 
series airplanes), which is not incorporated by reference by this 
AD.

(j) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
has the authority to approve AMOCs for this AD, if requested using 
the procedures found in 14 CFR 39.19. In accordance with 14 CFR 
39.19, send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Branch, send it to ATTN: Dan Rodina, 
Aerospace Engineer, International Branch, ANM-116, Transport 
Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, WA 98057-
3356; telephone 425-227-2125; fax 425-227-1149. Information may be 
emailed to: <a href="/cdn-cgi/l/email-protection#edd4c0aca3a0c0dcdcdbc0aca0a2aec0bfa8bcb8a8beb9bead8b8c8cc38a829b"><span class="__cf_email__" data-cfemail="437a6e020d0e6e7272756e020e0c006e1106121606101710032522226d242c35">[email&#160;protected]</span></a>.
    (i) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office. The AMOC approval letter must specifically 
reference this AD.
    (ii) AMOCs approved previously for AD 2008-06-18, Amendment 39-
15430 (73 FR 14670, March 19, 2008), are approved as AMOCs for the 
corresponding requirements of this AD.
    (2) Contacting the Manufacturer: As of the effective date of 
this AD, for any requirement in this AD to obtain corrective actions 
from a manufacturer, the action must be accomplished using a method 
approved by the Manager, International Branch, ANM-116, Transport 
Airplane Directorate, FAA; or the EASA; or Airbus's EASA DOA. If 
approved by the DOA, the approval must include the DOA-authorized 
signature.
    (3) Reporting Requirements: A federal agency may not conduct or 
sponsor, and a person is not required to respond to, nor shall a 
person be subject to a penalty for failure to comply with a 
collection of information subject to the requirements of the 
Paperwork Reduction Act unless that collection of information 
displays a current valid OMB Control Number. The OMB Control Number 
for this information collection is 2120-0056. Public reporting for 
this collection of information is estimated to be approximately 5 
minutes per response, including the time for reviewing instructions, 
completing and reviewing the collection of information. All 
responses to this collection of information are mandatory. Comments 
concerning the accuracy of this burden and suggestions for reducing 
the burden should be directed to the FAA at: 800 Independence Ave. 
SW., Washington, DC 20591, Attn: Information Collection Clearance 
Officer, AES-200.

(k) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) EASA Airworthiness Directive 2012-0203, dated October 1, 
2012, for related information. This MCAI may be found in the AD 
docket on the Internet at <a href="http://www.regulations.gov">http://www.regulations.gov</a> by searching 
for and locating Docket No. FAA-2014-0618.
    (2) Service information identified in this AD that is not 
incorporated by reference is available at the addresses specified in 
paragraphs (l)(5) and (l)(6) of this AD.

(l) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (3) The following service information was approved for IBR on 
July 21, 2015.
    (i) Airbus Service Bulletin A300-57-6029, Revision 08, dated 
April 25, 2013.
    (ii) Reserved.
    (4) The following service information was approved for IBR on 
April 23, 2008 (73 FR 14670, March 19, 2008).
    (i) Airbus Service Bulletin A300-57-0177, Revision 05, dated 
March 23, 2007.
    (ii) Airbus Service Bulletin A300-57-6029, Revision 06, dated 
March 23, 2007.
    (5) For service information identified in this AD, contact 
Airbus SAS Airworthiness Office--EAW, 1 Rond Point Maurice Bellonte, 
31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 
61 93 44 51; email <a href="/cdn-cgi/l/email-protection#751416161a001b015b141c07021a07011d5810140635141c071700065b161a18"><span class="__cf_email__" data-cfemail="fb9a9898948e958fd59a92898c94898f93d69e9a88bb9a9289998e88d5989496">[email&#160;protected]</span></a>; Internet <a href="http://www.airbus.com">http://www.airbus.com</a>.
    (6) You may view this service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For 
information on the availability of this material at the FAA, call 
425-227-1221.
    (7) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: <a href="http://www.archives.gov/federal-register/cfr/ibr-locations.html">http://www.archives.gov/federal-register/cfr/ibr-locations.html</a>.

    Issued in Renton, Washington, on June 3, 2015.
Michael Kaszycki,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2015-14283 Filed 6-15-15; 8:45 am]
 BILLING CODE 4910-13-P