AD 2009-06-06
Applicability
| Type | Manufacturer | Model | Details |
|---|---|---|---|
| aircraft | Airbus | A310 | Airworthiness Directives; Airbus Model A310 Series Airplanes and Model A300-600 Series Airplanes |
Unsafe Condition
Failure of system components leading to reduced structural integrity of the airplanes.
AI-generated summary from the source AD text. Verify against the official source before acting.
Required Actions
Inspect for cracking of the flap transmission shafts and replace if necessary. Inspect the trimmable horizontal stabilizer actuator (THSA) and perform corrective actions if necessary. Revise the Airworthiness Limitations Section of the Instructions for Continued Airworthiness to incorporate new limitations and maintenance tasks for aging systems maintenance.
AI-generated summary from the source AD text. Verify against the official source before acting.
Compliance Time
Within the compliance times specified in the referenced ADs.
AI-generated summary from the source AD text. Verify against the official source before acting.
Affected Aircraft
All Airbus Model A310 series airplanes and Model A300-600 series airplanes, certificated in any category.
AI-generated summary from the source AD text. Verify against the official source before acting.
Federal Register Abstract
This airworthiness directive (AD) supersedes two existing ADs. One AD applies to certain Airbus Model A310-200 and -300 series airplanes. That AD currently requires repetitive inspections for cracking of the flap transmission shafts, and replacement of the transmission shafts if necessary. That AD also provides an optional terminating action for the repetitive inspections. The other existing AD applies to all Airbus Model A300 B4-600, B4-600R, and F4-600R series airplanes, and Model C4-605R Variant F airplanes (collectively called A300-600 series airplanes); and Model A310-200 and -300 series airplanes. That AD currently requires a one-time inspection of the trimmable horizontal stabilizer actuator (THSA), corrective actions if necessary, and follow-on repetitive tasks. This new AD also requires revising the Airworthiness Limitations Section of the Instructions for Continued Airworthiness to incorporate new limitations and maintenance tasks for aging systems maintenance. This AD results from the manufacturer's determination that life limitations and maintenance tasks are necessary to ensure continued operational safety of the affected airplanes. We are issuing this AD to prevent reduced structural integrity of these airplanes due to the failure of system components.
Document Text
Show stored source text (verify against official source)
[Federal Register Volume 74, Number 55 (Tuesday, March 24, 2009)]
[Rules and Regulations]
[Pages 12228-12233]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: E9-5969]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2008-0018; Directorate Identifier 2007-NM-145-AD;
Amendment 39-15842; AD 2009-06-06]
RIN 2120-AA64
Airworthiness Directives; Airbus Model A310 Series Airplanes and
Model A300-600 Series Airplanes
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: This airworthiness directive (AD) supersedes two existing ADs.
One AD applies to certain Airbus Model A310-200 and -300 series
airplanes. That AD currently requires repetitive inspections for
cracking of the flap transmission shafts, and replacement of the
transmission shafts if necessary. That AD also provides an optional
terminating action for the repetitive inspections. The other existing
AD applies to all Airbus Model A300 B4-600, B4-600R, and F4-600R series
airplanes, and Model C4-605R Variant F airplanes (collectively called
A300-600 series airplanes); and Model A310-200 and -300 series
airplanes. That AD currently requires a one-time inspection of the
trimmable horizontal stabilizer actuator (THSA), corrective actions if
necessary, and follow-on repetitive tasks. This new AD also requires
revising the Airworthiness Limitations Section of the Instructions for
Continued Airworthiness to incorporate new limitations and maintenance
tasks for aging systems maintenance. This AD results from the
manufacturer's determination that life limitations and maintenance
tasks are necessary to ensure continued operational safety of the
affected airplanes. We are issuing this AD to prevent reduced
structural integrity of these airplanes due to the failure of system
components.
DATES: This AD becomes effective April 28, 2009.
The Director of the Federal Register approved the incorporation by
reference of certain publications listed in the AD as of April 28,
2009.
On August 29, 2006 (71 FR 42021, July 25, 2006), the Director of
the Federal Register approved the incorporation by reference of Airbus
Service Bulletin A300-27-6044, Revision 04, dated September 10, 2001;
and Airbus Service Bulletin A310-27-2089, Revision 02, dated June 28,
2001.
On June 20, 2006 (71 FR 28254, May 16, 2006), the Director of the
Federal Register approved the incorporation by reference of Airbus
Service Bulletin A310-27-2092, Revision 02, dated April 11, 2005; and
Airbus Service Bulletin A310-27-2095, dated March 29, 2000.
ADDRESSES: For Airbus service information identified in this AD,
contact Airbus SAS-EAW (Airworthiness Office), 1 Rond Point Maurice
Bellonte, 31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax
+33 5 61 93 44 51; e-mail: <a href="/cdn-cgi/l/email-protection#7b1a1818140e150f551a12090c14090f13561e1a083b1a1209190e0855181416"><span class="__cf_email__" data-cfemail="157476767a607b613b747c67627a67617d3870746655747c677760663b767a78">[email protected]</span></a>; Internet
<a href="http://www.airbus.com">http://www.airbus.com</a>. For TRW Aeronautical Systems service information
identified in this AD, contact TRW Syst[egrave]mes A[eacute]ronautiques
Civils SAS, Product Support Department, 7-9 Avenue de l'Eguillette,
Saint Ouen l'Aumone BP 7186, 95056 Cergy-Pontoise Cedex France,
telephone +33 1 34 32 63 00; fax +33 1 34 32 63 10.
Examining the AD Docket
You may examine the AD docket on the Internet at <a href="http://www.regulations.gov">http://www.regulations.gov</a>; or in person at the Docket Management Facility
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains this AD, the regulatory evaluation,
any comments received, and
[[Page 12229]]
other information. The address for the Docket Office (telephone 800-
647-5527) is the Document Management Facility, U.S. Department of
Transportation, Docket Operations, M-30, West Building Ground Floor,
Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590.
FOR FURTHER INFORMATION CONTACT: Thomas Stafford, Aerospace Engineer,
International Branch, ANM-116, Transport Airplane Directorate, FAA,
1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425)
227-1622; fax (425) 227-1149.
SUPPLEMENTARY INFORMATION:
Discussion
The FAA issued a supplemental notice of proposed rulemaking (NPRM)
to amend 14 CFR part 39 to include an AD that supersedes two existing
ADs: AD 2006-10-11, amendment 39-14595 (71 FR 28254, May 16, 2006); and
AD 2006-15-10, amendment 39-14690 (71 FR 42021, July 25, 2006). AD
2006-10-11 applies to certain Airbus Model A310-200 and -300 series
airplanes and requires repetitive inspections for cracking of the flap
transmission shafts, and replacing the transmission shafts if
necessary. That existing AD also provides an optional terminating
action for the repetitive inspections. AD 2006-15-10 applies to all
Airbus Model A310 and A300-600 series airplanes and requires a one-time
inspection of the trimmable horizontal stabilizer actuator (THSA),
corrective actions if necessary, and follow-on repetitive tasks.
That supplemental NPRM was published in the Federal Register on
September 26, 2008 (73 FR 55781). That supplemental NPRM proposed to
continue to require the actions required by the two existing ADs. That
supplemental NPRM also proposed to require revising the Airworthiness
Limitations Section of the Instructions for Continued Airworthiness to
incorporate new limitations and maintenance tasks for aging systems
maintenance. In addition, that supplemental NPRM proposed to revise the
original NPRM by reducing the initial compliance times.
Comments
We provided the public the opportunity to participate in the
development of this AD. No comments have been received on the
supplemental NPRM or on the determination of the cost to the public.
Explanation of Changes
We have removed the ``Service Bulletin References'' paragraph in
the ``RESTATEMENT OF REQUIREMENTS OF AD 2006-15-10'' section of this
AD. Instead, we refer to the required service documents in the
individual paragraphs of this AD.
Conclusion
We have carefully reviewed the available data and determined that
air safety and the public interest require adopting the AD with the
changes described previously. We also determined that these changes
will not increase the economic burden on any operator or increase the
scope of the AD.
Costs of Compliance
The following table provides the estimated costs for U.S. operators
to comply with this AD.
Estimated Costs
----------------------------------------------------------------------------------------------------------------
Number of
Average U.S.-
Action Work hours labor rate Cost per airplane registered Fleet cost
per hour airplanes
----------------------------------------------------------------------------------------------------------------
Inspection (required by AD 2006- 1 $80 $80 per inspection 59 $4,720 per
10-11). cycle. inspection cycle.
Inspection (required by AD 2006- 3 80 $240............... 213 $51,120.
15-10).
Repetitive follow-on tasks 12 80 $960 per inspection 213 $204,480 per
(required by AD 2006-15-10). cycle. inspection cycle.
ALS revision (new action)....... 1 80 $80................ 213 $17,040.
----------------------------------------------------------------------------------------------------------------
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, Section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701, ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We have determined that this AD will not have federalism
implications under Executive Order 13132. This AD will not have a
substantial direct effect on the States, on the relationship between
the national government and the States, or on the distribution of power
and responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866;
(2) Is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979); and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this AD and placed it in the AD docket. See the ADDRESSES
section for a location to examine the regulatory evaluation.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
0
Accordingly, under the authority delegated to me by the Administrator,
the FAA amends 14 CFR part 39 as follows:
[[Page 12230]]
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The Federal Aviation Administration (FAA) amends Sec. 39.13 by
removing amendment 39-14595 (71 FR 28254, May 16, 2006), and amendment
39-14690 (71 FR 42021, July 25, 2006), and by adding the following new
airworthiness directive (AD):
2009-06-06 Airbus: Amendment 39-15842. Docket No. FAA-2008-0018;
Directorate Identifier 2007-NM-145-AD.
Effective Date
(a) This AD becomes effective April 28, 2009.
Affected ADs
(b) This AD supersedes AD 2006-10-11 and AD 2006-15-10.
Applicability
(c) This AD applies to all Airbus Model A310 series airplanes;
and Model A300-600 series airplanes; certificated in any category.
Note 1: This AD requires revisions to certain operator
maintenance documents to include new inspections. Compliance with
these inspections is required by 14 CFR 91.403(c). For airplanes
that have been previously modified, altered, or repaired in the
areas addressed by these inspections, the operator may not be able
to accomplish the inspections described in the revisions. In this
situation, to comply with 14 CFR 91.403(c), the operator must
request approval for an alternative method of compliance according
to paragraph (q) of this AD. The request should include a
description of changes to the required inspections that will ensure
the continued operational safety of the airplane.
Unsafe Condition
(d) This AD results from the manufacturer's determination that
life limitations and maintenance tasks are necessary to ensure
continued operational safety of the affected airplanes. We are
issuing this AD to prevent reduced structural integrity of these
airplanes due to the failure of system components.
Compliance
(e) You are responsible for having the actions required by this
AD performed within the compliance times specified, unless the
actions have already been done.
Restatement of Requirements of AD 2006-10-11
Inspection and Corrective Action
(f) For Airbus Model A310-203, -204, -221, -222, -304, -322, -
324, and -325 airplanes, except for airplanes on which Airbus
Modification 12247 has been embodied in production: At the earlier
of the compliance times specified in paragraph (f)(1) or (f)(2) of
this AD, perform a detailed inspection for stress corrosion cracking
of the flight transmission shafts located between the power control
unit (PCU) and the torque limiters in accordance with the
Accomplishment Instructions of Airbus Service Bulletin A310-27-2092,
Revision 02, dated April 11, 2005. Thereafter, repeat the
inspections as required by paragraph (g) of this AD. Before further
flight, replace any cracked transmission shaft discovered during any
inspection required by this AD with a new or reconditioned shaft, in
accordance with the Accomplishment Instructions of Airbus Service
Bulletin A310-27-2095, dated March 29, 2000. Doing an inspection in
accordance with paragraph (n) or (o) of this AD terminates the
requirements of this paragraph.
(1) Within 2,000 flight hours after the last flap asymmetry
protection test performed in accordance with Airbus A310 Maintenance
Planning Document (MPD) Task 275600-01-1.
(2) Within 8,000 flight cycles after the last flap asymmetry
protection test performed in accordance with Airbus A310 MPD Task
275600-02-1 or 800 flight cycles after June 20, 2006 (the effective
date of AD 2006-10-11), whichever comes later.
Note 2: Airbus Service Bulletin A310-27-2092, Revision 02, dated
April 11, 2005, refers to Lucas Liebherr Service Bulletin 551A-27-
624, Revision 1, dated August 18, 2000, as a source of service
information for accomplishing the inspections.
Note 3: Airbus Service Bulletin A310-27-2092, Revision 02, dated
April 11, 2005, refers to Airbus Service Bulletin A310-27-2095,
dated March 29, 2000, as a source of information for replacing the
flap transmission shafts.
Note 4: Airbus Service Bulletin A310-27-2095, dated March 29,
2000, refers to Lucas Liebherr Service Bulletin 551A-27-M551-05,
dated January 12, 2000, as an additional source of information for
replacing the flap transmission shafts.
Repetitive Inspections
(g) Repeat the inspection required by paragraph (f) of this AD
at the applicable times specified in paragraphs (g)(1), (g)(2), and
(g)(3) of this AD. Doing an inspection in accordance with paragraph
(n) or (o) of this AD terminates the requirements of this paragraph.
(1) Before further flight after any occurrence of jamming of the
flap transmission system.
(2) At intervals not to exceed 2,000 flight hours after each
flap asymmetry protection test performed in accordance with Airbus
A310 MPD Task 275600-01-1.
(3) At intervals not to exceed 8,000 flight cycles after each
flap asymmetry protection test performed in accordance with Airbus
A310 MPD Task 275600-02-1.
Optional Terminating Action
(h) Replacing any flap transmission shaft with a new or
reconditioned transmission shaft in accordance with the
Accomplishment Instructions of Airbus Service Bulletin A310-27-2095,
dated March 29, 2000, ends the inspections required by paragraphs
(f) and (g) of this AD for that transmission shaft only.
Actions Performed Using Previously Issued Service Information
(i) Actions performed in accordance with Airbus Service Bulletin
A310-27-2092, dated April 9, 1999; or Revision 01, dated December
11, 2001; are considered acceptable for compliance with the
corresponding requirements of paragraphs (f) and (g) of this AD.
No Reporting
(j) Although Airbus Service Bulletin A310-27-2092, Revision 02,
dated April 11, 2005, specifies to submit certain information to the
manufacturer, this AD does not include that requirement.
Restatement of Requirements of AD 2006-15-10
Inspection
(k) At the applicable time specified in paragraph (k)(1) or
(k)(2) of this AD, do a detailed inspection of specified components
of the trimmable horizontal stabilizer actuator (THSA) in accordance
with paragraph 1.E.(2)(a) and the Accomplishment Instructions of the
applicable service bulletin as identified in Table 1 of this AD.
Repair any discrepancy before further flight in accordance with TRW
Aeronautical Systems Horizontal Stabilizer Actuator 47142 Series
Component Maintenance Manual with Illustrated Parts List 27-44-13,
Revision 6, dated September 14, 2001; or a method approved by the
Manager, International Branch, ANM-116, Transport Airplane
Directorate, FAA, or the European Aviation Safety Agency (EASA) (or
its delegated agent). Doing an inspection in accordance with
paragraph (n) or (o) of this AD terminates the requirements of this
paragraph.
(1) If the flight hours accumulated on the THSA can be
positively determined: Inspect at the earlier of:
(i) Before the accumulation of 47,000 total flight hours on the
THSA, or within 600 flight hours after August 29, 2006 (the
effective date of AD 2006-15-10), whichever occurs later.
(ii) Within 25 years since the THSA was new or within 600 flight
hours after August 29, 2006, whichever occurs later.
(2) If the flight hours accumulated on the THSA cannot be
positively determined: Inspect before the accumulation of 47,000
total flight hours on the airplane, or within 600 flight hours after
August 29, 2006, whichever occurs later.
[[Page 12231]]
Table 1--Service Bulletins for the Requirements of Paragraph (k) of This
AD
------------------------------------------------------------------------
Approved Airbus
Service Bulletin
version for
Required Airbus Service Bulletin actions done Airbus airplane
before the model
effective date of
this AD
------------------------------------------------------------------------
Airbus Service Bulletin A300-27- A300-27-6044, A300 B4-601, B4-
6044, Revision 04, dated Revision 02, 603, B4-620, and
September 10, 2001; or Airbus dated August 26, B4-622.
Mandatory Service Bulletin A300- 2000; or Revision A300 B4-605R and
27-6044, Revision 05, dated 03, dated June B4-622R.
August 29, 2006. 28, 2001. A300 B4-605R and
B4-622R.
A300 C4-605R
Variant F.
Airbus Service Bulletin A310-27- .................. A310-203, -204, -
2089, Revision 02, dated June 221, and -222.
28, 2001; or Airbus Mandatory A310-304, -322, -
Service Bulletin A310-27-2089, 324, and -325.
Revision 03, dated August 29,
2006.
------------------------------------------------------------------------
Note 5: The service bulletins specified in Table 1 of this AD
refer to Goodrich Actuation Systems Service Bulletin 47142-27-11,
Revision 3, dated April 25, 2005, as an additional source of service
information for the required actions.
Note 6: For the purposes of this AD, a detailed inspection is:
``An intensive examination of a specific item, installation, or
assembly to detect damage, failure, or irregularity. Available
lighting is normally supplemented with a direct source of good
lighting at an intensity deemed appropriate. Inspection aids such as
mirror, magnifying lenses, etc., may be necessary. Surface cleaning
and elaborate procedures may be required.''
Follow-on Repetitive Tasks
(l) After the inspection required by paragraph (k) of this AD:
Do the repetitive tasks in accordance with the Accomplishment
Instructions and at the times specified in paragraph 1.E.(2)(b) of
the applicable service bulletin identified in Table 2 of this AD,
except as provided by paragraph (m) of this AD. The repetitive tasks
are valid only until the THSA operational life exceeds 65,000 flight
hours, 40,000 flight cycles, or 25 years, whichever occurs first.
Before the THSA is operated beyond these extended life goals, it
must be replaced with a new or serviceable THSA, except as required
by paragraph (m) of this AD. Doing an inspection in accordance with
paragraph (n) or (o) of this AD terminates the requirements of this
paragraph.
Table 2--Service Bulletins for the Requirements of Paragraph (l) of This
AD
------------------------------------------------------------------------
Approved Airbus
Service Bulletin
version for
Required Airbus Service Bulletin actions done Airbus airplane
before the model
effective date of
this AD
------------------------------------------------------------------------
Airbus Service Bulletin A300-27- A300-27-6044, A300 B4-601, B4-
6044, Revision 04, dated Revision 02, 603, B4-620, and
September 10, 2001; or Airbus dated August 26, B4-622.
Mandatory Service Bulletin A300- 2000; or Revision A300 B4-605R and
27-6044, Revision 05, dated 03, dated June B4-622R.
August 29, 2006. 28, 2001. A300 B4-605R and
B4-622R.
A300 C4-605R
Variant F.
Airbus Service Bulletin A310-27- A310-27-2089, A310-203, -204, -
2089, Revision 02, dated June Revision 01, 221, and -222.
28, 2001; or Airbus Mandatory dated August 25, A310-304, -322, -
Service Bulletin A310-27-2089, 2000. 324, and -325.
Revision 03, dated August 29,
2006.
------------------------------------------------------------------------
Note 7: For additional information on the THSA life limits,
refer to Airbus Operators Information Telex (OIT) SE 999.0074/05/BB,
dated August 3, 2005.
THSA Replacement
(m) For any THSA, whether discrepant or not, that is replaced
with a new or serviceable THSA: Within 47,000 flight hours or 25
years, whichever occurs first, after the THSA is replaced, do the
applicable tasks specified in paragraph 1.E.(2)(a) and the
Accomplishment Instructions of the applicable service bulletin
identified in Table 3. Thereafter repeat the tasks within the
repetitive intervals specified in paragraph 1.E.(2)(b) of the
applicable service bulletin. Doing the corresponding tasks in
accordance with paragraph (n) or (o) of this AD terminates the
requirements of this paragraph.
Table 3--Service Bulletins for the Requirements of Paragraph (m) of This
AD
------------------------------------------------------------------------
Approved Airbus
Service Bulletin
version for
Required Airbus Service Bulletin actions done Airbus airplane
before the model
effective date of
this AD
------------------------------------------------------------------------
Airbus Service Bulletin A300-27- A300-27-6044, A300 B4-601, B4-
6044, Revision 04, dated Revision 02, 603, B4-620, and
September 10, 2001; or Airbus dated August 26, B4-622.
Mandatory Service Bulletin A300- 2000; or Revision A300 B4-605R and
27-6044, Revision 05, dated 03, dated June B4-622R.
August 29, 2006. 28, 2001. A300 F4-605R and
F4-622R.
A300 C4-605R
Variant F.
Airbus Service Bulletin A310-27- A310-27-2089, A310-203, -204, -
2089, Revision 02, dated June Revision 01, 221, and -222.
28, 2001; or Airbus Mandatory dated August 25, A310-304, -322, -
Service Bulletin A310-27-2089, 2000. 324, and -325.
Revision 03, dated August 29,
2006.
------------------------------------------------------------------------
[[Page 12232]]
New Requirements of This AD
Revise Airworthiness Limitations Section (ALS) To Incorporate
Limitations and Maintenance Tasks for Aging Systems Maintenance
(n) Within 3 months after the effective date of this AD, revise
the ALS of the Instructions for Continued Airworthiness (ICA) to
incorporate Airbus A310 ALS Part 4--Ageing Systems Maintenance,
Revision 01, dated December 21, 2006 (for Model A310 series
airplanes); or Airbus A300-600 ALS Part 4--Ageing Systems
Maintenance, Revision 01, dated December 21, 2006 (for Model A300-
600 series airplanes). For all tasks identified in Airbus A310 ALS
Part 4--Ageing Systems Maintenance, Revision 01, dated December 21,
2006; and Airbus A300-600 ALS Part 4--Ageing Systems Maintenance,
Revision 01, dated December 21, 2006; do the tasks at the later of
the times specified in paragraphs (n)(1) and (n)(2) of this AD, as
applicable, except as provided by paragraph (o) of this AD. The
repetitive inspections must be accomplished thereafter at the
interval specified in Airbus A310 ALS Part 4--Ageing Systems
Maintenance, Revision 01, dated December 21, 2006; or Airbus A300-
600 ALS Part 4--Ageing Systems Maintenance, Revision 01, dated
December 21, 2006; as applicable. Doing an inspection required by
this paragraph terminates the corresponding inspection required by
paragraph (f), (g), (k), (l), or (m) of this AD.
(1) At the initial compliance times (thresholds) specified in
Airbus A310 ALS Part 4--Ageing Systems Maintenance, Revision 01,
dated December 21, 2006; or Airbus A300-600 ALS Part 4--Ageing
Systems Maintenance, Revision 01, dated December 21, 2006; as
applicable; with the compliance times starting from the later of the
times specified in paragraphs (n)(1)(i) and (n)(1)(ii) of this AD.
(i) Since first flight of the airplane.
(ii) Since the applicable part was new or refurbished if the
part's life (in flight hours, flight cycles, landings, or calendar
time, as applicable) can be conclusively determined.
(2) Within 3 months after doing the revision of the ALS of the
ICA required by paragraph (o) of this AD.
Note 8: For additional information on the THSA life limits,
refer to Airbus OIT SE 999.0074/05/BB, dated August 3, 2005.
Note 9: For additional information on the THSA life limits and
calculation method for unknown history of parts, refer to Airbus OIT
SE 999.0008/07/LB, dated January 16, 2007; and Airbus Service
Information Letter 05-008, Revision 01, dated February 21, 2007.
(o) For airplanes on which any life limitation/maintenance task
has been complied with in accordance with the requirements of
paragraph (f), (g), (k), (l), or (m) of this AD (e.g., AD 2006-10-11
or AD 2006-15-10), the last accomplishment of each limitation/task
must be retained as a starting point for the accomplishment of each
corresponding limitation/task interval now introduced in Airbus A310
ALS Part 4--Ageing Systems Maintenance, Revision 01, dated December
21, 2006; and Airbus A300-600 ALS Part 4--Ageing Systems
Maintenance, Revision 01, dated December 21, 2006; as applicable.
Doing an inspection required by this paragraph terminates the
corresponding inspection required by paragraph (f), (g), (k), (l),
or (m) of this AD.
(p) Except as provided by paragraph (q) of this AD: After
accomplishing the actions specified in paragraphs (n) and (o) of
this AD, no alternative inspection, inspection intervals, or
limitations may be used.
Alternative Methods of Compliance (AMOCs)
(q)(1) The Manager, International Branch, ANM-116, Transport
Airplane Directorate, FAA, has the authority to approve AMOCs for
this AD, if requested using the procedures found in 14 CFR 39.19.
Send information to ATTN: Thomas Stafford, Aerospace Engineer,
International Branch, ANM-116, Transport Airplane Directorate, FAA,
1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone
(425) 227-1622; fax (425) 227-1149. Before using any approved AMOC
on any airplane to which the AMOC applies, notify your appropriate
principal inspector (PI) in the FAA Flight Standards District Office
(FSDO), or lacking a PI, your local FSDO.
(2) AMOCs approved previously in accordance with AD 2006-10-11
are not approved as AMOCs with this AD.
(3) AMOCs approved previously in accordance with AD 2006-15-10
are not approved as AMOCs with this AD.
Related Information
(r) EASA airworthiness directive 2007-0092, dated April 10,
2007, also addresses the subject of this AD.
Material Incorporated by Reference
(s) You must use the service information identified in Table 4
of this AD, as applicable, to do the actions required by this AD,
unless the AD specifies otherwise. If you accomplish the optional
actions specified by this AD, you must use Airbus Service Bulletin
A310-27-2095, dated March 29, 2000, to perform those actions, unless
the AD specifies otherwise.
Table 4--Material Incorporated by Reference for the Actions Required by This AD
----------------------------------------------------------------------------------------------------------------
Document Revision Date
----------------------------------------------------------------------------------------------------------------
Airbus A300-600 Airworthiness 01........................ December 21, 2006.
Limitations Section (ALS) Part 4--
Ageing Systems Maintenance.
Airbus A310 Airworthiness Limitations 01........................ December 21, 2006.
Section (ALS) Part 4--Ageing Systems
Maintenance.
Airbus Mandatory Service Bulletin A300- 05........................ August 29, 2006.
27-6044.
Airbus Mandatory Service Bulletin A310- 03........................ August 29, 2006.
27-2089.
Airbus Service Bulletin A300-27-6044... 04........................ September 10, 2001.
Airbus Service Bulletin A310-27-2089... 02........................ June 28, 2001.
Airbus Service Bulletin A310-27-2092... 02........................ April 11, 2005.
Airbus Service Bulletin A310-27-2095... Original.................. March 29, 2000.
TRW Aeronautical Systems Horizontal 6......................... September 14, 2001.
Stabilizer Actuator 47142 Series
Component Maintenance Manual with
Illustrated Parts List 27-44-13.
----------------------------------------------------------------------------------------------------------------
(TRW Aeronautical Systems Horizontal Stabilizer Actuator 47142
Series Component Maintenance Manual with Illustrated Parts List 27-
44-13 contains the following discrepancies: The revision level of
the document is only specified on the Letter of Transmittal; the
Letter of Transmittal is not specified in the List of Effective
Pages; and the List of Effective Pages refers to page 748a as 748b.)
(1) The Director of the Federal Register approved the
incorporation by reference of the service information contained in
Table 5 of this AD under 5 U.S.C. 552(a) and 1 CFR part 51.
Table 5--New Material Incorporated by Reference
----------------------------------------------------------------------------------------------------------------
Document Revision Date
----------------------------------------------------------------------------------------------------------------
Airbus A300-600 Airworthiness 01........................ December 21, 2006.
Limitations Section (ALS) Part 4--
Ageing Systems Maintenance.
Airbus A310 Airworthiness Limitations 01........................ December 21, 2006.
Section (ALS) Part 4--Ageing Systems
Maintenance.
Airbus Mandatory Service Bulletin A300- 05........................ August 29, 2006.
27-6044.
Airbus Mandatory Service Bulletin A310- 03........................ August 29, 2006.
27-2089.
[[Page 12233]]
TRW Aeronautical Systems Horizontal Original.................. September 14, 2001.
Stabilizer Actuator 47142 Series
Component Maintenance Manual with
Illustrated Parts List 27-44-13.
----------------------------------------------------------------------------------------------------------------
(2) The Director of the Federal Register previously approved the
incorporation by reference of the service information contained in
Table 6 of this AD on August 29, 2006 (71 FR 42021, July 25, 2006).
Table 6--Material Previously Incorporated by Reference in AD 2006-15-10
----------------------------------------------------------------------------------------------------------------
Document Revision Date
----------------------------------------------------------------------------------------------------------------
Airbus Service Bulletin A300-27-6044......... 04 September 10, 2001.
Airbus Service Bulletin A310-27-2089......... 02 June 28, 2001.
----------------------------------------------------------------------------------------------------------------
(3) The Director of the Federal Register previously approved the
incorporation by reference of the service information contained in
Table 7 of this AD on June 20, 2006 (71 FR 28254, May 16, 2006).
Table 7--Material Previously Incorporated by Reference in AD 2006-10-11
----------------------------------------------------------------------------------------------------------------
Document Revision Date
----------------------------------------------------------------------------------------------------------------
Airbus Service Bulletin A310-27-2092... 02........................ April 11, 2005.
Airbus Service Bulletin A310-27-2095... Original.................. March 29, 2000.
----------------------------------------------------------------------------------------------------------------
(4) For Airbus service information identified in this AD,
contact Airbus SAS--EAW (Airworthiness Office), 1 Rond Point Maurice
Bellonte, 31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96;
fax +33 5 61 93 44 51; e-mail: <a href="/cdn-cgi/l/email-protection#48292b2b273d263c6629213a3f273a3c20652d293b0829213a2a3d3b662b2725"><span class="__cf_email__" data-cfemail="3d5c5e5e52485349135c544f4a524f495510585c4e7d5c544f5f484e135e5250">[email protected]</span></a>;
Internet <a href="http://www.airbus.com">http://www.airbus.com</a>.
(5) For TRW Aeronautical Systems service information identified
in this AD, contact TRW Syst[eacute]mes Aeacute;ronautiques Civils
SAS, Product Support Department, 7-9 Avenue de l'Eguillette, Saint
Ouen l'Aumone BP 7186, 95056 Cergy-Pontoise Cedex France, telephone
+33 1 34 32 63 00; fax +33 1 34 32 63 10.
(6) You may review copies of the service information at the FAA,
Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton,
Washington. For information on the availability of this material at
the FAA, call 425-227-1221 or 425-227-1152.
(7) You may also review copies of the service information
incorporated by reference at the National Archives and Records
Administration (NARA). For information on the availability of this
material at NARA, call 202-741-6030, or go to: <a href="http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html">http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html</a>.
Issued in Renton, Washington, on February 27, 2009.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. E9-5969 Filed 3-23-09; 8:45 am]
BILLING CODE 4910-13-P
Source: Official FAA Source ↗
Retrieved: Apr 4, 2026
Rights: U.S. Government Public Domain
This site is not affiliated with or endorsed by the FAA. Always verify with official sources.