AD 2007-18-02

[Federal Register Volume 72, Number 166 (Tuesday, August 28, 2007)]
[Rules and Regulations]
[Pages 49175-49177]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: E7-16911]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2007-28379; Directorate Identifier 2007-NM-077-AD; 
Amendment 39-15182; AD 2007-18-02]
RIN 2120-AA64


Airworthiness Directives; Airbus Model A300 Series Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for the 
products listed above. This AD results from mandatory continuing 
airworthiness information (MCAI) originated by an aviation authority of 
another country to identify and correct an unsafe condition on an 
aviation product. The MCAI describes the unsafe condition as:

    [T]he FAA has published SFAR 88 (Special Federal Aviation 
Regulation 88). * * *
    Under this regulation, all holders of type certificates for 
passenger transport aircraft * * * are required to conduct a design 
review against explosion risks.
    This Airworthiness Directive (AD), which renders mandatory the 
modification of the fuel pump wiring against short circuit, is a 
consequence of this design review.

The unsafe condition is chafing of the fuel pump cables, which could 
result in short circuits leading to fuel pump

[[Page 49176]]

failure, intermittent operation, arcing, and possible fuel tank 
explosion. We are issuing this AD to require actions to correct the 
unsafe condition on these products.

DATES: This AD becomes effective October 2, 2007.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of October 2, 
2007.

ADDRESSES: You may examine the AD docket on the Internet at http://
<a href="<a href="http://dms.dot.gov">http://dms.dot.gov</a>">dms.dot.gov</a> or in person at the U.S. Department of Transportation, 
Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 
New Jersey Avenue, SE., Washington, DC.

FOR FURTHER INFORMATION CONTACT: Tom Stafford, Aerospace Engineer, 
International Branch, ANM-116, FAA, Transport Airplane Directorate, 
1601 Lind Avenue SW., Renton, Washington 98057-3356; telephone (425) 
227-1622; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION:

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 to include an AD that would apply to the specified products. 
That NPRM was published in the Federal Register on June 28, 2007 (72 FR 
35368). That NPRM proposed to correct an unsafe condition for the 
specified products. The MCAI states:

    [T]he FAA has published SFAR 88 (Special Federal Aviation 
Regulation 88). In their letters referenced 04/00/02/07/01-L296, 
dated March 4th, 2002 and 04/00/02/07/03-L024, dated February 3rd, 
2003, the JAA (Joint Aviation Authorities) recommended the 
application of a similar regulation to the National Aviation 
Authorities (NAA).
    Under this regulation, all holders of type certificates for 
passenger transport aircraft with either a passenger capacity of 30 
or more, or a payload capacity of 7,500 pounds (3402 kg) or more, 
which have received their certification since January 1st, 1958, are 
required to conduct a design review against explosion risks.
    This Airworthiness Directive (AD), which renders mandatory the 
modification of the fuel pump wiring against short circuit, is a 
consequence of this design review.
    Note: for A310 and A300-600 aircraft, refer to [EASA] AD 2006-
0284R1. [On March 7, 2007, the FAA issued a corresponding NPRM for 
Model A310 and A300-600 airplanes, which was published in the 
Federal Register (72 FR 11302, March 13, 2007.)]

The unsafe condition is chafing of the fuel pump cables, which could 
result in short circuits leading to fuel pump failure, intermittent 
operation, arcing, and possible fuel tank explosion. You may obtain 
further information by examining the MCAI in the AD docket.

Comments

    We gave the public the opportunity to participate in developing 
this AD. We received no comments on the NPRM or on the determination of 
the cost to the public.

Conclusion

    We reviewed the available data and determined that air safety and 
the public interest require adopting the AD as proposed.

Differences Between This AD and the MCAI or Service Information

    We have reviewed the MCAI and related service information and, in 
general, agree with their substance. But we might have found it 
necessary to use different words from those in the MCAI to ensure the 
AD is clear for U.S. operators and is enforceable. In making these 
changes, we do not intend to differ substantively from the information 
provided in the MCAI and related service information.
    We might also have required different actions in this AD from those 
in the MCAI in order to follow our FAA policies. Any such differences 
are highlighted in a NOTE within the AD.

Costs of Compliance

    Based on the service information, we estimate that this AD affects 
about 29 products of U.S. registry. We also estimate that it takes 
about 72 work-hours per product to comply with the basic requirements 
of this AD. The average labor rate is $80 per work-hour. Required parts 
cost about $5,050 per product. Where the service information lists 
required parts costs that are covered under warranty, we have assumed 
that there will be no charge for these costs. As we do not control 
warranty coverage for affected parties, some parties may incur costs 
higher than estimated here. Based on these figures, we estimate the 
cost of this AD on U.S. operators to be $313,490, or $10,810 per 
product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify this AD:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this AD and placed it in the AD docket.

Examining the AD Docket

    You may examine the AD docket on the Internet at http//dms.dot.gov; 
or in person at the Docket Operations office between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
the NPRM, the regulatory evaluation, any comments received, and other 
information. The street address for the Docket Operations office 
(telephone (800) 647-5527) is in the ADDRESSES section. Comments will 
be available in the AD docket shortly after receipt.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

0
Accordingly, under the authority delegated to me by the Administrator, 
the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:


[[Page 49177]]


    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new AD:

2007-18-02 Airbus: Amendment 39-15182. Docket No. FAA-2007-28379; 
Directorate Identifier 2007-NM-077-AD.

Effective Date

    (a) This airworthiness directive (AD) becomes effective October 
2, 2007.

Affected ADs

    (b) None.

Applicability

    (c) This AD applies to Airbus Model A300 series airplanes, all 
certified models, all serial numbers, certificated in any category; 
except Model A300-600 series airplanes; and except those modified by 
Airbus Service Bulletin A300-24-0103, Revision 01, dated January 11, 
2007.

Subject

    (d) Air Transport Association (ATA) of America Code 24: 
Electrical Power.

Reason

    (e) The mandatory continuing airworthiness information (MCAI) 
states:
    [T]he FAA has published SFAR 88 (Special Federal Aviation 
Regulation 88). In their letters referenced 04/00/02/07/01-L296, 
dated March 4th, 2002 and 04/00/02/07/03-L024, dated February 3rd, 
2003, the JAA (Joint Aviation Authorities) recommended the 
application of a similar regulation to the National Aviation 
Authorities (NAA).
    Under this regulation, all holders of type certificates for 
passenger transport aircraft with either a passenger capacity of 30 
or more, or a payload capacity of 7,500 pounds (3402 kg) or more, 
which have received their certification since January 1st, 1958, are 
required to conduct a design review against explosion risks.
    This Airworthiness Directive (AD), which renders mandatory the 
modification of the fuel pump wiring against short circuit, is a 
consequence of this design review.

    Note: For A310 and A300-600 aircraft, refer to [EASA] AD 2006-
0284R1. [On March 7, 2007, the FAA issued a corresponding NPRM for 
Model A310 and A300-600 airplanes, which was published in the 
Federal Register (72 FR 11302, March 13, 2007.)]


The unsafe condition is chafing of the fuel pump cables, which could 
result in short circuits leading to fuel pump failure, intermittent 
operation, arcing, and possible fuel tank explosion.

Actions and Compliance

    (f) Within 31 months after the effective date of this AD, unless 
already done, modify the inner and outer fuel pumps wiring, route 1P 
and 2P harnesses in the LH (left-hand) wing and in the RH (right-
hand) wing, in accordance with the Accomplishment Instructions of 
Airbus Service Bulletin A300-24-0103, Revision 01, dated January 11, 
2007. Actions done before the effective date of this AD in 
accordance with Airbus Service Bulletin A300-24-0103, dated March 
15, 2006, for airplanes under configuration 1 as defined in the 
service bulletin, are acceptable for compliance with the 
requirements of this AD.

FAA AD Differences

    Note: This AD differs from the MCAI and/or service information 
as follows: No differences.

Other FAA AD Provisions

    (g) The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
has the authority to approve AMOCs for this AD, if requested using 
the procedures found in 14 CFR 39.19. Send information to ATTN: Tom 
Stafford, Aerospace Engineer, International Branch, ANM-116, FAA, 
Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, 
Washington 98057-3356; telephone (425) 227-1622; fax (425) 227-1149. 
Before using any approved AMOC on any airplane to which the AMOC 
applies, notify your appropriate principal inspector (PI) in the FAA 
Flight Standards District Office (FSDO), or lacking a PI, your local 
FSDO.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.
    (3) Reporting Requirements: For any reporting requirement in 
this AD, under the provisions of the Paperwork Reduction Act, the 
Office of Management and Budget (OMB) has approved the information 
collection requirements and has assigned OMB Control Number 2120-
0056.

Related Information

    (h) Refer to MCAI European Aviation Safety Agency (EASA) 
Airworthiness Directive 2007-0066, dated March 13, 2007, and Airbus 
Service Bulletin A300-24-0103, Revision 01, dated January 11, 2007, 
for related information.

Material Incorporated by Reference

    (i) You must use Airbus Service Bulletin A300-24-0103, Revision 
01, dated January 11, 2007, to do the actions required by this AD, 
unless the AD specifies otherwise.
    (1) The Director of the Federal Register approved the 
incorporation by reference of this service information under 5 
U.S.C. 552(a) and 1 CFR part 51.
    (2) For service information identified in this AD, contact 
Airbus, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France.
    (3) You may review copies at the FAA, Transport Airplane 
Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the 
National Archives and Records Administration (NARA). For information 
on the availability of this material at NARA, call (202) 741-6030, 
or go to: <a href="http://www.archives.gov/federal-register/cfr/ibr-locations.html">http://www.archives.gov/federal-register/cfr/ibr-locations.html</a>.

    Issued in Renton, Washington, on August 17, 2007.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
 [FR Doc. E7-16911 Filed 8-27-07; 8:45 am]
BILLING CODE 4910-13-P