AD 2007-17-15

[Federal Register Volume 72, Number 166 (Tuesday, August 28, 2007)]
[Rules and Regulations]
[Pages 49155-49157]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: E7-16672]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2007-28300; Directorate Identifier 2006-NM-292-AD; 
Amendment 39-15173; AD 2007-17-15]
RIN 2120-AA64


Airworthiness Directives; Airbus Model A300 Series Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for the 
products listed above. This AD results from mandatory continuing 
airworthiness information (MCAI) originated by an aviation authority of 
another country to identify and correct an unsafe condition on an 
aviation product. The MCAI describes the unsafe condition as:

    The Chromic Acid Anodising (CAA) Lead Fleet Program was 
established in 1989 to observe corrosion/debonding behaviour of CAA-
treated panels. CAA lead fleet includes the inspection of lap 
joints, circumferential joints, stringers and doublers on selected 
aircraft.
    The findings in combination with analytical corrosion 
investigations have been analysed by the TC (type certificate) 
holder and an appropriate inspection program for debonding has been 
developed.
    This airworthiness directive requires inspection of the 
concerned areas to detect any corrosion and/or debonding which could 
affect the structural integrity. * * *

The proposed AD would require actions that are intended to address the 
unsafe condition described in the MCAI.

DATES: This AD becomes effective October 2, 2007.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of October 2, 
2007.

ADDRESSES: You may examine the AD docket on the Internet at <a href="http://dms.dot.gov">http://dms.dot.gov</a> or in person at the U.S. Department of Transportation, 
Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 
New Jersey Avenue, SE., Washington, DC.

FOR FURTHER INFORMATION CONTACT: Tom Stafford, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 
227-1622; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION:

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 to include an AD that would apply to the specified products. 
That NPRM was published in the Federal Register on May 29, 2007 (72 FR 
29449). That NPRM proposed to correct an unsafe condition for the 
specified products. The MCAI states:

    The Chromic Acid Anodising (CAA) Lead Fleet Program was 
established in 1989 to observe corrosion/debonding behaviour of CAA-
treated panels. CAA lead fleet includes the inspection of lap 
joints, circumferential joints, stringers and doublers on selected 
aircraft.
    The findings in combination with analytical corrosion 
investigations have been analysed by the TC (type certificate) 
holder and an appropriate inspection program for debonding has been 
developed.
    This airworthiness directive requires inspection of the 
concerned areas [including repetitive inspections of certain areas] 
to detect any corrosion and/or debonding which could affect the 
structural integrity. * * *

If any discrepancies are found, repair and follow-up actions 
(additional inspections for debonding and corrosion depth) are 
required.

Comments

    We gave the public the opportunity to participate in developing 
this AD. We received no comments on the NPRM or on the determination of 
the cost to the public.

Conclusion

    We reviewed the available data and determined that air safety and 
the public interest require adopting the AD as proposed.

Differences Between This AD and the MCAI or Service Information

    We have reviewed the MCAI and related service information and, in 
general, agree with their substance. But we might have found it 
necessary to use different words from those in the MCAI to ensure the 
AD is clear for U.S. operators and is enforceable. In making these 
changes, we do not intend to differ substantively from the information 
provided in the MCAI and related service information.
    We might also have required different actions in this AD from those 
in the MCAI in order to follow our FAA policies. Any such differences 
are highlighted in a NOTE within the AD.

Costs of Compliance

    Based on the service information, we estimate that this AD affects 
about 12 products of U.S. registry. We also estimate that it takes 102 
work-hours per product to comply with the basic requirements of this 
AD. The average labor rate is $80 per work-hour. Based on these 
figures, we estimate the cost of the AD on U.S. operators to be 
$97,920, or $8,160 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify this AD:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and

[[Page 49156]]

    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this AD and placed it in the AD docket.

Examining the AD Docket

    You may examine the AD docket on the Internet at <a href="http://dms.dot.gov">http://dms.dot.gov</a>; or in person at the Docket Operations office between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains the NPRM, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Operations office (telephone (800) 647-5527) is in the ADDRESSES 
section. Comments will be available in the AD docket shortly after 
receipt.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

0
Accordingly, under the authority delegated to me by the Administrator, 
the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new AD:

2007-17-15 Airbus: Amendment 39-15173. Docket No. FAA-2007-28300; 
Directorate Identifier 2006-NM-292-AD.

Effective Date

    (a) This airworthiness directive (AD) becomes effective October 
2, 2007.

Affected ADs

    (b) None.

Applicability

    (c) This AD applies to Airbus Model A300 series aircraft, 
certificated in any category, manufacturing serial numbers (MSN) 
0105 through 0107, 0116, 0117, 0121, 0123 through 0126, 0128, 0129, 
0133 through 0141, 0146 through 0152, 0154 through 0157, 0160, 0163, 
0170, 0173, 0175 through 0177, and 0180 through 0183.

Subject

    (d) Air Transport Association (ATA) of America Code 53: 
Fuselage.

Reason

    (e) The mandatory continuing airworthiness information (MCAI) 
states:

    The Chromic Acid Anodising (CAA) Lead Fleet Program was 
established in 1989 to observe corrosion/debonding behaviour of CAA-
treated panels. CAA lead fleet includes the inspection of lap 
joints, circumferential joints, stringers and doublers on selected 
aircraft.
    The findings in combination with analytical corrosion 
investigations have been analysed by the TC (type certificate) 
holder and an appropriate inspection program for debonding has been 
developed.
    This airworthiness directive requires inspection of the 
concerned areas [including repetitive inspections of certain areas] 
to detect any corrosion and/or debonding which could affect the 
structural integrity.* * *

If any discrepancies are found, repair and follow-up actions 
(additional inspections for debonding and corrosion depth) are 
required.

Actions and Compliance

    (f) Unless already done, do the following actions.
    (1) Except as provided by paragraphs (f)(2), (f)(3), and (f)(4) 
of this AD: Do the initial and repetitive inspections (including 
follow-up actions), as applicable; and do all applicable repairs; of 
the areas specified in paragraphs (f)(1)(i), (f)(1)(ii), 
(f)(1)(iii), and (f)(1)(iv) of this AD, in accordance with the 
Accomplishment Instructions of Airbus Service Bulletin A300-53-0378, 
dated September 4, 2006, and within the timescales specified in 
paragraph 1.E.(2), the Accomplishment Instructions, and the figures 
of the service bulletin.
    (i) The bonded doubler in the longitudinal lap joint area 
between frame (FR)18 and FR80 (configurations 01 and 02 inspect FR18 
through FR40; configuration 03 inspects FR18 through FR80).
    (ii) The bonded wing doublers between stringer (STGR)22 LH/RH 
(left-hand/right-hand) and STGR43 LH/RH for debonding (configuration 
01 of the service bulletin only).
    (iii) The bonded doublers in the circumferential joint area 
between FR26 and FR80 (configurations 01 and 02 inspect FR26 through 
FR40; configuration 03 inspects FR26 through FR80).
    (iv) The bonded doublers in the manhole area between FR23 RH and 
FR24 RH and between FR38.1 RH and FR38.2 RH.
    (2) Where paragraph 1.E.(2) of Airbus Service Bulletin A300-53-
0378, dated September 4, 2006, specifies a grace period from CN 
(Consigne de Navigabilit[eacute]) issuance, this AD requires a grace 
period relative to the effective date of this AD.
    (3) Where paragraph 1.E.(2) of Airbus Service Bulletin A300-53-
0378, dated September 4, 2006, specifies a threshold, this AD 
requires that the inspections be done within the specified threshold 
relative to the first flight of the airplane.
    (4) Where the Accomplishment Instructions and figures of Airbus 
Service Bulletin A300-53-0378, dated September 4, 2006, specify that 
inspections be done ``yearly,'' this AD requires those inspections 
to be done at intervals not to exceed 1 year.

FAA AD Differences

    Note: This AD differs from the MCAI and/or service information 
as follows: No differences.

Other FAA AD Provisions

    (g) The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
has the authority to approve AMOCs for this AD, if requested using 
the procedures found in 14 CFR 39.19. Send information to ATTN: Tom 
Stafford, Aerospace Engineer, International Branch, ANM-116, 
Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, 
Washington 98057-3356; telephone (425) 227-1622; fax (425) 227-1149. 
Before using any approved AMOC on any airplane to which the AMOC 
applies, notify your appropriate principal inspector (PI) in the FAA 
Flight Standards District Office (FSDO), or lacking a PI, your local 
FSDO.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.
    (3) Reporting Requirements: For any reporting requirement in 
this AD, under the provisions of the Paperwork Reduction Act, the 
Office of Management and Budget (OMB) has approved the information 
collection requirements and has assigned OMB Control Number 2120-
0056.

Related Information

    (h) Refer to MCAI European Aviation Safety Agency Airworthiness 
Directive 2006-0369, dated December 12, 2006; and Airbus Service 
Bulletin A300-53-0378, dated September 4, 2006, for related 
information.

Material Incorporated by Reference

    (i) You must use Airbus Service Bulletin A300-53-0378, dated 
September 4, 2006, to do the actions required by this AD, unless the 
AD specifies otherwise.
    (1) The Director of the Federal Register approved the 
incorporation by reference of this service information under 5 
U.S.C. 552(a) and 1 CFR part 51.
    (2) For service information identified in this AD, contact 
Airbus, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France.
    (3) You may review copies at the FAA, Transport Airplane 
Directorate, 1601 Lind Avenue SW., Renton, Washington; or at the 
National Archives and Records Administration (NARA). For information 
on the availability of this material at NARA, call (202) 741-6030, 
or go to: <a href="http://www.archives.gov/federal-register/cfr/ibr-locations.html">http://www.archives.gov/federal-register/cfr/ibr-locations.html</a>.


[[Page 49157]]


    Issued in Renton, Washington, on August 14, 2007.
Stephen P. Boyd,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. E7-16672 Filed 8-27-07; 8:45 am]
BILLING CODE 4910-13-P