AD 99-10-04

final rule

Airworthiness Directives; British Aerospace (Jetstream) Model 4101 Airplanes

AD Number
99-10-04
Status
final_rule
Effective Date
Product Category
aircraft
Docket
98-NM-308-AD
FR Citation
This information is not available.
Technical illustration of an aircraft flight control surface and actuator
Problem area Flight controls

Applicability

TypeManufacturerModelDetails
aircraft BAE Systems (Operations) Limited Jetstream Model 4101 Airworthiness Directives; British Aerospace (Jetstream) Model 4101 Airplanes

Unsafe Condition

Failure of the pulley assemblies of the elevator and rudder control cables in the event of an elevator or rudder control cable jam, which could result in reduced controllability of the airplane.

AI-generated summary from the source AD text. Verify against the official source before acting.

Required Actions

Modify the pulley assemblies of the elevator and rudder control cables on the rear pressure bulkhead in accordance with Jetstream Service Bulletin J41-27-052. Compliance must be within 12 months after the effective date of this AD.

AI-generated summary from the source AD text. Verify against the official source before acting.

Compliance Time

Within 12 months after the effective date of this AD

AI-generated summary from the source AD text. Verify against the official source before acting.

Affected Aircraft

All Jetstream Model 4101 airplanes, certificated in any category.

AI-generated summary from the source AD text. Verify against the official source before acting.

Federal Register Abstract

Pulley Assembly of Elevator and Rudder Control Cables

Applicability Source Text

Show captured applicability text from the source AD
AD Final Rules - DRS_99-10-04.html
Copy URL
Print/Save as PDF
Document Versions
 Feedback
Details
AD Number:
99-10-04
Document Type:
AD Final Rules
Docket Number:
98-NM-308-AD
Subject Heading:
Airworthiness Directives; British Aerospace (Jetstream) Model 4101 Airplanes
Subject:
Pulley Assembly of Elevator and Rudder Control Cables
Status:
Current
Citation:
This information is not available.
Citation Publish Date:
Effective Date:
06/09/1999
Make:
BAE Systems (Operations) Limited
Model:
Jetstream Model 4101
Product Type:
Aircraft
Product Subtype:
Large Airplane
Affected AD:
Superseded AD:
Affected By:
Superseded By:
Service/Office:
Office of Primary Responsibility:
CFR Part Reference:
Part 39 [64 FR 24033 No. 86 05/05/99]
Comments:
AIRWORTHINESS DIRECTIVES FINAL RULES: 99-10-04
CITATION:   This information is not available.

PAGE NUMBER:  

DOCKET NUMBER:   98-NM-308-AD

AMENDMENT:   39-11158

AD NUMBER:   99-10-04

SUBJECT HEADING:   Airworthiness Directives; British Aerospace (Jetstream) Model 4101 Airplanes

ACTION:   Final rule

SUMMARY:   This amendment adopts a new airworthiness directive (AD), applicable to all British Aerospace (Jetstream) Model 4101 airplanes, that requires modification of the pulley assemblies of the elevator and rudder control cables on the rear pressure bulkhead. This amendment is prompted by issuance of mandatory continuing airworthiness information by a foreign civil airworthiness authority. The actions specified by this AD are intended to prevent failure of the pulley assemblies of the elevator and rudder control cables in the event of an elevator or rudder control cable jam, which could result in reduced controllability of the airplane.

DATES:   Effective June 9, 1999. The incorporation by reference of certain publications listed in the regulations is approved by the Director of the Federal Register as of June 9, 1999.

ADDRESSES:   The service information referenced in this AD may be obtained from AI(R) American Support, Inc., 13850 Mclearen Road, Herndon, Virginia 20171. This information may be examined at the Federal Aviation Administration (FAA), Transport Airplane Directorate, Rules Docket, 1601 Lind Avenue, SW., Renton, Washington; or at the Office of the Federal Register, 800 North Capitol Street, NW., suite 700, Washington, DC.

FOR FURTHER INFORMATION CONTACT:   Norman B. Martenson, Manager, International Branch, ANM-116, FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425) 227-2110; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION:  
A proposal to amend part 39 of the Federal Aviation Regulations (14 CFR part 39) to include an airworthiness directive (AD) that is applicable to all British Aerospace (Jetstream) Model 4101 airplanes was published in the Federal Register on February 18, 1999 (64 FR 8026). That action proposed to require modification of the pulley assemblies of the elevator and rudder control cables on the rear pressure bulkhead.

Comments
Interested persons have been afforded an opportunity to participate in the making of this amendment. No comments were submitted in response to the proposal or the FAA's determination of the cost to the public.

Conclusion
After careful review of the available data, the FAA has determined that air safety and the public interest require the adoption of the rule as proposed.

Cost Impact
The FAA estimates that 60 airplanes of U.S. registry will be affected by this AD, that it will take approximately 60 work hours per airplane to accomplish the required actions, and that the average labor rate is $60 per work hour. Required parts will be supplied by the manufacturer at no cost to the operators. Based on these figures, the cost impact of the AD on U.S. operators is estimated to be $216,000, or $3,600 per airplane.

The cost impact figure discussed above is based on assumptions that no operator has yet accomplished any of the requirements of this AD action, and that no operator would accomplish those actions in the future if this AD were not adopted.

Regulatory Impact
The regulations adopted herein will not have substantial direct effects on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. Therefore, in accordance with Executive Order 12612, it is determined that this final rule does not have sufficient federalism implications to warrant the preparation of a Federalism Assessment.

For the reasons discussed above, I certify that this action (1) is not a "significant regulatory action" under Executive Order 12866; (2) is not a "significant rule" under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and (3) will not have a significant economic impact, positive or negative, on a substantial number of small entities
under the criteria of the Regulatory Flexibility Act. A final evaluation has been prepared for this action and it is contained in the Rules Docket. A copy of it may be obtained from the Rules Docket at the location provided under the caption "ADDRESSES."

List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

Adoption of the Amendment
Accordingly, pursuant to the authority delegated to me by the Administrator, the Federal Aviation Administration amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39 - AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]
2. Section 39.13 is amended by adding the following new airworthiness directive:

REGULATORY TEXT:  
99-10-04 BRITISH AEROSPACE REGIONAL AIRCRAFT [Formerly Jetstream Aircraft Limited; British Aerospace (Commercial Aircraft) Limited]: Amendment 39-11158. Docket 98-NM-308-AD.
Applicability: All Jetstream Model 4101 airplanes, certificated in any category.

NOTE 1: This AD applies to each airplane identified in the preceding applicability provision, regardless of whether it has been modified, altered, or repaired in the area subject to the requirements of this AD. For airplanes that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/operator must request approval for an alternative method of compliance in accordance with paragraph (b) of this AD. The request should include an assessment of the effect of the modification, alteration, or repair on the unsafe condition addressed by this AD; and, if the unsafe condition has not been eliminated, the request should include specific proposed actions to address it.

Compliance: Required as indicated, unless accomplished previously.

To prevent failure of the pulley assemblies of the elevator and rudder control cables in the event of an elevator or rudder control cable jam, which could result in reduced controllability of the airplane, accomplish the following:

(a) Within 12 months after the effective date of this AD, modify the pulley assemblies of the elevator and rudder control cables on the rear pressure bulkhead, in accordance with Jetstream Service Bulletin J41-27-052, dated September 11, 1998.

Alternative Methods of Compliance

(b) An alternative method of compliance or adjustment of the compliance time that provides an acceptable level of safety may be used if approved by the Manager, International Branch, ANM-116, Transport Airplane Directorate. Operators shall submit their requests through an appropriate FAA Principal Maintenance Inspector, who may add comments and then send it to the Manager, International Branch, ANM-116.

NOTE 2: Information concerning the existence of approved alternative methods of compliance with this AD, if any, may be obtained from the International Branch, ANM-116.

Special Flight Permits

(c) Special flight permits may be issued in accordance with sections 21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 and 21.199) to operate the airplane to a location where the requirements of this AD can be accomplished.

Incorporation by Reference

(d) The modification shall be done in accordance with Jetstream Service Bulletin J41-27-052, dated September 11, 1998. This incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from AI(R) American Support, Inc., 13850 Mclearen Road, Herndon, Virginia 20171. Copies may be inspected at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the Office of the Federal Register, 800 North Capitol Street, NW., suite 700, Washington, DC.

NOTE 3: The subject of this AD is addressed in British airworthiness directive 006-09-98.

(e) This amendment becomes effective on June 9, 1999.

FOOTER:

Document Text

Show stored source text (verify against official source)
AD Final Rules - DRS_99-10-04.html
Copy URL
Print/Save as PDF
Document Versions
 Feedback
Details
AD Number:
99-10-04
Document Type:
AD Final Rules
Docket Number:
98-NM-308-AD
Subject Heading:
Airworthiness Directives; British Aerospace (Jetstream) Model 4101 Airplanes
Subject:
Pulley Assembly of Elevator and Rudder Control Cables
Status:
Current
Citation:
This information is not available.
Citation Publish Date:
Effective Date:
06/09/1999
Make:
BAE Systems (Operations) Limited
Model:
Jetstream Model 4101
Product Type:
Aircraft
Product Subtype:
Large Airplane
Affected AD:
Superseded AD:
Affected By:
Superseded By:
Service/Office:
Office of Primary Responsibility:
CFR Part Reference:
Part 39 [64 FR 24033 No. 86 05/05/99]
Comments:
AIRWORTHINESS DIRECTIVES FINAL RULES: 99-10-04
CITATION:   This information is not available.

PAGE NUMBER:  

DOCKET NUMBER:   98-NM-308-AD

AMENDMENT:   39-11158

AD NUMBER:   99-10-04

SUBJECT HEADING:   Airworthiness Directives; British Aerospace (Jetstream) Model 4101 Airplanes

ACTION:   Final rule

SUMMARY:   This amendment adopts a new airworthiness directive (AD), applicable to all British Aerospace (Jetstream) Model 4101 airplanes, that requires modification of the pulley assemblies of the elevator and rudder control cables on the rear pressure bulkhead. This amendment is prompted by issuance of mandatory continuing airworthiness information by a foreign civil airworthiness authority. The actions specified by this AD are intended to prevent failure of the pulley assemblies of the elevator and rudder control cables in the event of an elevator or rudder control cable jam, which could result in reduced controllability of the airplane.

DATES:   Effective June 9, 1999. The incorporation by reference of certain publications listed in the regulations is approved by the Director of the Federal Register as of June 9, 1999.

ADDRESSES:   The service information referenced in this AD may be obtained from AI(R) American Support, Inc., 13850 Mclearen Road, Herndon, Virginia 20171. This information may be examined at the Federal Aviation Administration (FAA), Transport Airplane Directorate, Rules Docket, 1601 Lind Avenue, SW., Renton, Washington; or at the Office of the Federal Register, 800 North Capitol Street, NW., suite 700, Washington, DC.

FOR FURTHER INFORMATION CONTACT:   Norman B. Martenson, Manager, International Branch, ANM-116, FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425) 227-2110; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION:  
A proposal to amend part 39 of the Federal Aviation Regulations (14 CFR part 39) to include an airworthiness directive (AD) that is applicable to all British Aerospace (Jetstream) Model 4101 airplanes was published in the Federal Register on February 18, 1999 (64 FR 8026). That action proposed to require modification of the pulley assemblies of the elevator and rudder control cables on the rear pressure bulkhead.

Comments
Interested persons have been afforded an opportunity to participate in the making of this amendment. No comments were submitted in response to the proposal or the FAA's determination of the cost to the public.

Conclusion
After careful review of the available data, the FAA has determined that air safety and the public interest require the adoption of the rule as proposed.

Cost Impact
The FAA estimates that 60 airplanes of U.S. registry will be affected by this AD, that it will take approximately 60 work hours per airplane to accomplish the required actions, and that the average labor rate is $60 per work hour. Required parts will be supplied by the manufacturer at no cost to the operators. Based on these figures, the cost impact of the AD on U.S. operators is estimated to be $216,000, or $3,600 per airplane.

The cost impact figure discussed above is based on assumptions that no operator has yet accomplished any of the requirements of this AD action, and that no operator would accomplish those actions in the future if this AD were not adopted.

Regulatory Impact
The regulations adopted herein will not have substantial direct effects on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. Therefore, in accordance with Executive Order 12612, it is determined that this final rule does not have sufficient federalism implications to warrant the preparation of a Federalism Assessment.

For the reasons discussed above, I certify that this action (1) is not a "significant regulatory action" under Executive Order 12866; (2) is not a "significant rule" under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and (3) will not have a significant economic impact, positive or negative, on a substantial number of small entities
under the criteria of the Regulatory Flexibility Act. A final evaluation has been prepared for this action and it is contained in the Rules Docket. A copy of it may be obtained from the Rules Docket at the location provided under the caption "ADDRESSES."

List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

Adoption of the Amendment
Accordingly, pursuant to the authority delegated to me by the Administrator, the Federal Aviation Administration amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39 - AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]
2. Section 39.13 is amended by adding the following new airworthiness directive:

REGULATORY TEXT:  
99-10-04 BRITISH AEROSPACE REGIONAL AIRCRAFT [Formerly Jetstream Aircraft Limited; British Aerospace (Commercial Aircraft) Limited]: Amendment 39-11158. Docket 98-NM-308-AD.
Applicability: All Jetstream Model 4101 airplanes, certificated in any category.

NOTE 1: This AD applies to each airplane identified in the preceding applicability provision, regardless of whether it has been modified, altered, or repaired in the area subject to the requirements of this AD. For airplanes that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/operator must request approval for an alternative method of compliance in accordance with paragraph (b) of this AD. The request should include an assessment of the effect of the modification, alteration, or repair on the unsafe condition addressed by this AD; and, if the unsafe condition has not been eliminated, the request should include specific proposed actions to address it.

Compliance: Required as indicated, unless accomplished previously.

To prevent failure of the pulley assemblies of the elevator and rudder control cables in the event of an elevator or rudder control cable jam, which could result in reduced controllability of the airplane, accomplish the following:

(a) Within 12 months after the effective date of this AD, modify the pulley assemblies of the elevator and rudder control cables on the rear pressure bulkhead, in accordance with Jetstream Service Bulletin J41-27-052, dated September 11, 1998.

Alternative Methods of Compliance

(b) An alternative method of compliance or adjustment of the compliance time that provides an acceptable level of safety may be used if approved by the Manager, International Branch, ANM-116, Transport Airplane Directorate. Operators shall submit their requests through an appropriate FAA Principal Maintenance Inspector, who may add comments and then send it to the Manager, International Branch, ANM-116.

NOTE 2: Information concerning the existence of approved alternative methods of compliance with this AD, if any, may be obtained from the International Branch, ANM-116.

Special Flight Permits

(c) Special flight permits may be issued in accordance with sections 21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 and 21.199) to operate the airplane to a location where the requirements of this AD can be accomplished.

Incorporation by Reference

(d) The modification shall be done in accordance with Jetstream Service Bulletin J41-27-052, dated September 11, 1998. This incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from AI(R) American Support, Inc., 13850 Mclearen Road, Herndon, Virginia 20171. Copies may be inspected at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the Office of the Federal Register, 800 North Capitol Street, NW., suite 700, Washington, DC.

NOTE 3: The subject of this AD is addressed in British airworthiness directive 006-09-98.

(e) This amendment becomes effective on June 9, 1999.

FOOTER:

Source: Official FAA Source ↗

Retrieved: Apr 8, 2026

Rights: U.S. Government Public Domain

This site is not affiliated with or endorsed by the FAA. Always verify with official sources.