AD 81-09-06

AD Final Rules - DRS_81-09-06.html
Copy URL
Print/Save as PDF
Document Versions
 Feedback
Details
AD Number:
81-09-06
Document Type:
AD Final Rules
Docket Number:
81-ASW-4
Subject Heading:
Airworthiness Directives; SOCIETE NATIONALE INDUSTRIELLE AEROSPATIALE Model AS350 Series Helicopters
Subject:
Bevel Gear Modules
Status:
Current
Citation:
Federal Register Volume 46, Number 136 (Thursday, July 16, 1981)
Citation Publish Date:
07/16/1981
Effective Date:
07/23/1981
Make:
Airbus Helicopters
Model:
AS350B | AS350C | AS350D | AS350D1
Product Type:
Aircraft
Product Subtype:
Rotorcraft
Affected AD:
Superseded AD:
Affected By:
Superseded By:
Service/Office:
AIR-700: Compliance & Airworthiness Division
Office of Primary Responsibility:
AIR-730: International Validation Branch
CFR Part Reference:
Part 39
Comments:
Updated RGL applicability to match AD applicability; CAR C-11-185
AIRWORTHINESS DIRECTIVES FINAL RULES: 81-09-06
CITATION:   This information is not available.

PAGE NUMBER:  

DOCKET NUMBER:   Unknown

AMENDMENT:   39-4161

AD NUMBER:   81-09-06

SUBJECT HEADING:   Airworthiness Directives; SOCIETE NATIONALE INDUSTRIELLE AEROSPATIALE Model AS350 Series Helicopters

ACTION:  

SUMMARY:  

DATES:   Effective July 23, 1981.

ADDRESSES:  

FOR FURTHER INFORMATION CONTACT:  

SUPPLEMENTARY INFORMATION:  

REGULATORY TEXT:  
81-09-06 SOCIETE NATIONALE INDUSTRIELLE AEROSPATIALE: Amendment 39- 4161. Applies to Model AS350 series helicopters certificated in all categories which have Bevel Gear Module P/N 350A32.0300.00 or -.01 installed, except bevel gear modules which include nitrided shaft P/N 350A32.3107.23 or -.24. (Bevel Gear Module P/N 350A32.0300.02 includes nitrided shaft, P/N 350A32.3107.23 or -.24 and is exempt from this application.)

Compliance required as follows, unless already accomplished:

a. For bevel gear modules with 580 or more hours' time in service since new or last overhaul, comply within 20 hours time in service after the effective date of this AD, or

b. For bevel gear modules with less than 580 hours' time in service since new or last overhaul on the effective date of this AD, comply prior to accumulation of 600 hours' time in service, and

c. Thereafter at intervals not to exceed 300 hours' time in service.

To prevent loss of mechanical drive between the bevel gear module and the epicyclic module of the main transmission gearbox, inspect the bevel gear module for wear in accordance with procedures specified in paragraph EE of Aerospatiale TELEX Service No. 05.05 (TELEX No. 22316) dated December 24, 1980, or paragraph BB of Aerospatiale TELEX Service No. 05.06 as it applies to measuring actual spline wear, or other FAA approved equivalent.

If the maximum wear depth at the level of the step on the spline exceeds 1.0 mm (0.039 inch) or if the distance between two rods of 6.35 mm (.250 inch) exceeds 72.2 mm (2.84 inches), the bevel gear module must be replaced with a serviceable module before further flight.

Report defects to the Chief, Aircraft Certification Staff, FAA, Europe, Africa, and Middle East Office, c/o American Embassy, Brussels, Belgium. Reporting approved by the Office of Management and Budget under OMB No. 04-R0174.

Special flight permits may be issued in accordance with FAR 21.197 and FAR 21.199 to fly aircraft to a base where this AD can be accomplished.

Equivalent methods of compliance with this AD must be approved by the Chief, Engineering and Manufacturing Branch, Flight Standards Division, Southwest Region, Federal Aviation Administration, P.O. Box 1689, Fort Worth, Texas 76101, or by the Chief, Aircraft Certification Staff, FAA, Europe, Africa, and Middle East Office, c/o American Embassy, Brussels, Belguim.

NOTE: Aerospatiale TELEX 22316, paragraph EE, is as follows:

EE. Remove main rotor mast and sun gear according to Work Cards 65 13 401 and 65 30 404. Check the wear of vertical shaft splines either by mold print, (maximum wear depth at the level of the step, 1mm (0.039 inches)) or by measurement of distance between two rods of 6.35 mm diameter. Distance between two opposite rods shall be less than 72.2 mm.

If the value obtained by either one of the above methods is out of limit, return bevel gear module to an approved repair station.

This Airworthiness Directive supersedes AD 81-01-05.

This amendment becomes effective July 23, 1981, for all persons except those to whom it was made immediately effective by priority mail AD No. 81-09-06 dated April 23, 1981.

FOOTER: