AD 62-26-05
final rule
Applicability
| Type | Manufacturer | Model | Details |
|---|---|---|---|
| aircraft | Piper Aircraft Inc. | PA-24 | Airworthiness Directives; Piper All Models PA-24 and PA-24 "250" Aircraft |
| aircraft | Piper Aircraft Inc. | PA-24-250 | Airworthiness Directives; Piper All Models PA-24 and PA-24 "250" Aircraft |
Unsafe Condition
Cracked muffler heater shrouds can cause hazardous carbon monoxide contamination in the cockpit and engine power loss.
AI-generated summary from the source AD text. Verify against the official source before acting.
Required Actions
Inspect muffler components for cracks, heat deterioration, defects, or wrinkles. Pressure test mufflers at 10 p.s.i. Replace mufflers if defects are found. Rework muffler heater shrouds by enlarging openings, installing reinforcement tubes and cover plates per Piper's specifications. Install new cabin heater shrouds for certain serial ranges. Reinstall components after modifications.
AI-generated summary from the source AD text. Verify against the official source before acting.
Compliance Time
within the next 50 hours' time in service after the effective date of this AD
AI-generated summary from the source AD text. Verify against the official source before acting.
Affected Aircraft
Piper PA-24 and PA-24-250 aircraft with serial numbers 24-1 to 24-3284, excluding specific serial numbers already modified.
AI-generated summary from the source AD text. Verify against the official source before acting.
Federal Register Abstract
Exhaust System
Applicability Source Text
Show captured applicability text from the source AD
AD Final Rules - DRS_62-26-05.html Copy URL Print/Save as PDF Document Versions Feedback Details AD Number: 62-26-05 Document Type: AD Final Rules Docket Number: Unknown Subject Heading: Airworthiness Directives; Piper All Models PA-24 and PA-24 "250" Aircraft Subject: Exhaust System Status: Current Citation: Federal Register: December 5, 1962 Citation Publish Date: 12/05/1962 Effective Date: 12/05/1962 Make: Piper Aircraft Inc. Model: PA-24 | PA-24-250 Product Type: Aircraft Product Subtype: Small Airplane Affected AD: Superseded AD: Affected By: Superseded By: Service/Office: AIR-700: Compliance & Airworthiness Division Office of Primary Responsibility: AIR-720: Operational Safety Branch CFR Part Reference: Part 39 Comments: AIRWORTHINESS DIRECTIVES FINAL RULES: 62-26-05 CITATION: [Federal Register: December 5, 1962] PAGE NUMBER: DOCKET NUMBER: Unknown AMENDMENT: AD NUMBER: 62-26-05 SUBJECT HEADING: Airworthiness Directives; Piper All Models PA-24 and PA-24 "250" Aircraft ACTION: SUMMARY: DATES: Effective December 5, 1962. ADDRESSES: FOR FURTHER INFORMATION CONTACT: SUPPLEMENTARY INFORMATION: REGULATORY TEXT: 62-26-05 PIPER: Amdt. 511 Part 507 Federal Register December 5, 1962. Applies to All Models PA-24 and PA-24 "250" Aircraft. Compliance required within the next 50 hours' time in service after the effective date of this AD, unless already accomplished. To preclude hazardous carbon monoxide contamination in the cockpit and engine power loss, caused by cracked muffler heater shrouds, accomplish the following: (a) For aircraft Serial Numbers 24-1 to 24-2298 inclusive, equipped with channel reinforced muffler P/N's 22594-00, 22594-02 on PA-24, and P/N's 22593-00, 23159-00 on PA-24 "250" installed as service replacements: (1) Remove the tail pipe, the right-hand exhaust stack, and carburetor heat shroud and inspect for cracks and hot spots. Pay particular attention to the junction of rear cylinder exhaust tube with the stack assembly. (2) Remove the muffler and muffler heater shroud. Carefully inspect the muffler for visible cracks, particularly in the area near the tail pipe opening and examine the internal baffle and perforated tube. Submerge the muffler in water and pressure test at 10 p.s.i. (3) Replace the muffler prior to further flight if cracks, heat deterioration, defects, or wrinkles formed in the perforated tube are observed or if leaks are detected during the pressure test. (4) Rework the muffler heater shroud by: (i) enlarging the opening in the shroud in accordance with the Piper template; (ii) installing the muffler reinforcement tube, P/N 23482-00 using 20 rivets PDR 134A-6, or FAA approved equivalent; and (iii) installing cover plate P/N 23498-00 using 11 rivets AN 426A3-4, or FAA approved equivalent, in accordance with Piper Immediate Action Service Bulletin No. 210 (Kit P/N 754 484). (5) Reinstall the muffler exhaust stacks, tailpipe, and air ducts on the airplane. (b) For aircraft Serial Numbers 24-2299 to 24-3284 inclusive, equipped with channel reinforced muffler P/N's 22594-00, 22594-02 on PA-24, and P/N's 22593-00, 23159-00 on PA-24 "250", except aircraft Serial Numbers 24-2876, 24-2929, 24-2949, 24-2967, 24-2990, 24-3033, 24-3095, 24-3114, 24-3130, 24-3150, 24-3155, 24-3173, 24-3191, 24-3193, 24-3194, 24-3196, 24-3198, 24-3203, 24-3204, 24-3222, 24-3233, 24-3234, 24-3241, 24-3244, 24-3248, 24-3254, 24-3257, 24-3258, 24-3265, 24-3268, 24-3270, 24-3273, 24-3274, 24-3276, 24-3277, 24-3278, 24-3279, 24-3280, 24-3282, 24-3283, which have been modified: (1) Perform inspections required by (a)(1) and (a)(2), and the replacement required by (a)(3), if necessary. (2) Install new cabin heater shroud, P/N 23507-00 on PA-24, and P/N 23489-00 on PA-24 "250". Center the tailpipe in the shroud tailpipe opening. (3) Reinstall the muffler exhaust stacks, tailpipe, and air ducts on airplane. NOTE: PA-24 and PA-24 "250" mufflers have been manufactured incorporating two different styles of tailpipe reinforcement brackets. This AD requires modification of one style only - those with channel style reinforcement. See Sketch A of Piper Service Bulletin No. 210 for further identification. Both types of mufflers have been sold as service replacements. It will therefore be necessary to examine aircraft Serial Numbers 24-1 to 24-2587 inclusive, if the original muffler has been replaced, to determine if the modification is required. Aircraft Serial Numbers 24-2588 through 24-3284, were manufactured with the channel shaped reinforcement and will require modification except those already modified as indicated. (Use Piper Service Letter No. 324B as a guide for inspections in addition to Service Bulletin No. 210.) This directive effective December 5, 1962. FOOTER:
Document Text
Show stored source text (verify against official source)
AD Final Rules - DRS_62-26-05.html Copy URL Print/Save as PDF Document Versions Feedback Details AD Number: 62-26-05 Document Type: AD Final Rules Docket Number: Unknown Subject Heading: Airworthiness Directives; Piper All Models PA-24 and PA-24 "250" Aircraft Subject: Exhaust System Status: Current Citation: Federal Register: December 5, 1962 Citation Publish Date: 12/05/1962 Effective Date: 12/05/1962 Make: Piper Aircraft Inc. Model: PA-24 | PA-24-250 Product Type: Aircraft Product Subtype: Small Airplane Affected AD: Superseded AD: Affected By: Superseded By: Service/Office: AIR-700: Compliance & Airworthiness Division Office of Primary Responsibility: AIR-720: Operational Safety Branch CFR Part Reference: Part 39 Comments: AIRWORTHINESS DIRECTIVES FINAL RULES: 62-26-05 CITATION: [Federal Register: December 5, 1962] PAGE NUMBER: DOCKET NUMBER: Unknown AMENDMENT: AD NUMBER: 62-26-05 SUBJECT HEADING: Airworthiness Directives; Piper All Models PA-24 and PA-24 "250" Aircraft ACTION: SUMMARY: DATES: Effective December 5, 1962. ADDRESSES: FOR FURTHER INFORMATION CONTACT: SUPPLEMENTARY INFORMATION: REGULATORY TEXT: 62-26-05 PIPER: Amdt. 511 Part 507 Federal Register December 5, 1962. Applies to All Models PA-24 and PA-24 "250" Aircraft. Compliance required within the next 50 hours' time in service after the effective date of this AD, unless already accomplished. To preclude hazardous carbon monoxide contamination in the cockpit and engine power loss, caused by cracked muffler heater shrouds, accomplish the following: (a) For aircraft Serial Numbers 24-1 to 24-2298 inclusive, equipped with channel reinforced muffler P/N's 22594-00, 22594-02 on PA-24, and P/N's 22593-00, 23159-00 on PA-24 "250" installed as service replacements: (1) Remove the tail pipe, the right-hand exhaust stack, and carburetor heat shroud and inspect for cracks and hot spots. Pay particular attention to the junction of rear cylinder exhaust tube with the stack assembly. (2) Remove the muffler and muffler heater shroud. Carefully inspect the muffler for visible cracks, particularly in the area near the tail pipe opening and examine the internal baffle and perforated tube. Submerge the muffler in water and pressure test at 10 p.s.i. (3) Replace the muffler prior to further flight if cracks, heat deterioration, defects, or wrinkles formed in the perforated tube are observed or if leaks are detected during the pressure test. (4) Rework the muffler heater shroud by: (i) enlarging the opening in the shroud in accordance with the Piper template; (ii) installing the muffler reinforcement tube, P/N 23482-00 using 20 rivets PDR 134A-6, or FAA approved equivalent; and (iii) installing cover plate P/N 23498-00 using 11 rivets AN 426A3-4, or FAA approved equivalent, in accordance with Piper Immediate Action Service Bulletin No. 210 (Kit P/N 754 484). (5) Reinstall the muffler exhaust stacks, tailpipe, and air ducts on the airplane. (b) For aircraft Serial Numbers 24-2299 to 24-3284 inclusive, equipped with channel reinforced muffler P/N's 22594-00, 22594-02 on PA-24, and P/N's 22593-00, 23159-00 on PA-24 "250", except aircraft Serial Numbers 24-2876, 24-2929, 24-2949, 24-2967, 24-2990, 24-3033, 24-3095, 24-3114, 24-3130, 24-3150, 24-3155, 24-3173, 24-3191, 24-3193, 24-3194, 24-3196, 24-3198, 24-3203, 24-3204, 24-3222, 24-3233, 24-3234, 24-3241, 24-3244, 24-3248, 24-3254, 24-3257, 24-3258, 24-3265, 24-3268, 24-3270, 24-3273, 24-3274, 24-3276, 24-3277, 24-3278, 24-3279, 24-3280, 24-3282, 24-3283, which have been modified: (1) Perform inspections required by (a)(1) and (a)(2), and the replacement required by (a)(3), if necessary. (2) Install new cabin heater shroud, P/N 23507-00 on PA-24, and P/N 23489-00 on PA-24 "250". Center the tailpipe in the shroud tailpipe opening. (3) Reinstall the muffler exhaust stacks, tailpipe, and air ducts on airplane. NOTE: PA-24 and PA-24 "250" mufflers have been manufactured incorporating two different styles of tailpipe reinforcement brackets. This AD requires modification of one style only - those with channel style reinforcement. See Sketch A of Piper Service Bulletin No. 210 for further identification. Both types of mufflers have been sold as service replacements. It will therefore be necessary to examine aircraft Serial Numbers 24-1 to 24-2587 inclusive, if the original muffler has been replaced, to determine if the modification is required. Aircraft Serial Numbers 24-2588 through 24-3284, were manufactured with the channel shaped reinforcement and will require modification except those already modified as indicated. (Use Piper Service Letter No. 324B as a guide for inspections in addition to Service Bulletin No. 210.) This directive effective December 5, 1962. FOOTER:
Source: Official FAA Source ↗
Retrieved: Apr 8, 2026
Rights: U.S. Government Public Domain
This site is not affiliated with or endorsed by the FAA. Always verify with official sources.
Related Airworthiness Directives
2024-14-03
final ruleAirworthiness Directives; Various Airplanes
Unsafe Condition: an un-commanded automatic pitch trim runaway when the autopilot was first engaged, which could result in un-commanded automatic pitch trim runaway and loss of control of the airplane.
2023-09-09 Recurring
final ruleAirworthiness Directives; Various Airplanes, Helicopters, and Engines
Unsafe Condition: Multiple failures of spot-welded, multi-segment v-band couplings at the tailpipe to the turbocharger exhaust housing flange.
2022-03-15
final ruleAirworthiness Directives; Various Airplanes
Unsafe Condition: The displayed fuel quantity can have an error as much as four gallons/fuel tank with the display indicating four gallons with an empty tank. In the context of this event, the end level effect is th...
2015-24-05
final ruleAirworthiness Directives; Piper Aircraft, Inc. Airplanes
Unsafe Condition: Fuel starvation due to the shape of the wing fuel tanks and fuel below a certain level in the tank allowing fuel to move away from the tank outlet during certain maneuvers.