AD 46-38-02

final rule

Airworthiness Directives; ERCO Model 415-C, -CD and -D Aircraft

AD Number
46-38-02
Status
final_rule
Effective Date
Product Category
aircraft
Docket
Unknown
FR Citation
This information is not available.
Technical illustration of an aircraft flight control surface and actuator
Problem area Flight controls

Applicability

TypeManufacturerModelDetails
aircraft Univair Aircraft Corporation 415-C Airworthiness Directives; ERCO Model 415-C, -CD and -D Aircraft
aircraft Univair Aircraft Corporation 415-CD Airworthiness Directives; ERCO Model 415-C, -CD and -D Aircraft
aircraft Univair Aircraft Corporation 415-D Airworthiness Directives; ERCO Model 415-C, -CD and -D Aircraft

Unsafe Condition

Cracks in the welds attaching aileron control stops to the control column cross member and insufficient welds at the ends of the stops, as well as potential turnbuckle-sprocket interference in the chain and cable system, could lead to loss of aileron control stop function.

AI-generated summary from the source AD text. Verify against the official source before acting.

Required Actions

Add an AN 315-3R nut and a star type AN 936-B10 lock washer on the aileron control stop adjustment screw. Inspect and repair cracked or insufficient welds attaching the aileron control stops. Inspect and readjust upper turnbuckles to prevent interference with sprockets before quadrant contact with stops.

AI-generated summary from the source AD text. Verify against the official source before acting.

Compliance Time

prior to November 1, 1946

AI-generated summary from the source AD text. Verify against the official source before acting.

Affected Aircraft

Univair Aircraft Corporation Model 415-C, -CD, and -D aircraft with serial numbers 113 to 2706 except 2683, 2685, 2687, and 2691.

AI-generated summary from the source AD text. Verify against the official source before acting.

Federal Register Abstract

Aileron control stop

Applicability Source Text

Show captured applicability text from the source AD
AD Final Rules - DRS_46-38-02.html
Copy URL
Print/Save as PDF
Document Versions
 Feedback
Details
AD Number:
46-38-02
Document Type:
AD Final Rules
Docket Number:
Unknown
Subject Heading:
Airworthiness Directives; ERCO Model 415-C, -CD and -D Aircraft
Subject:
Aileron control stop
Status:
Current
Citation:
This information is not available.
Citation Publish Date:
Effective Date:
Make:
Univair Aircraft Corporation
Model:
415-C | 415-CD | 415-D
Product Type:
Aircraft
Product Subtype:
Small Airplane
Affected AD:
Superseded AD:
Affected By:
Superseded By:
Service/Office:
Office of Primary Responsibility:
CFR Part Reference:
Part 39
Comments:
AIRWORTHINESS DIRECTIVES FINAL RULES: 46-38-02
CITATION:   This information is not available.

PAGE NUMBER:  

DOCKET NUMBER:   Unknown

AMENDMENT:  

AD NUMBER:   46-38-02

SUBJECT HEADING:   Airworthiness Directives; ERCO Model 415-C, -CD and -D Aircraft

ACTION:  

SUMMARY:  

DATES:  

ADDRESSES:  

FOR FURTHER INFORMATION CONTACT:  

SUPPLEMENTARY INFORMATION:  

REGULATORY TEXT:   46-38-02 ERCO: (Was Mandatory Note 8 of AD-718-6.) Applies to 415-C, -CD and -D Aircraft Serial Numbers 113 to 2706 Except 2683, 2685, 2687, and 2691.
Compliance required prior to November 1, 1946.
(a) To provide additional bearing area and more positive locking action for the aileron control stop adjustment screw, add an AN 315-3R nut on the adjustment screw at the forward side of the stops and a star type AN 936-B10 lock washer (external teeth) between the jam nut and rear side of stops (Ercoupe P/N 415-52145).
(b) Inspect the welds which attach the aileron control stops to the control column cross member carefully for cracks. Also determine that welds are complete around the ends of the stops. Repair if cracked welds or insufficient welds are found.
(c) Inspect the adjustment of the two upper turnbuckles in the chain and cable system to be certain these turnbuckles do not touch the sprockets before the quadrant touches the stops. Readjust all three turnbuckles if necessary to insure freedom from this turnbuckle-sprocket interference.
(Erco Service Department Bulletin No. 13 covers this same subject.)

FOOTER:

Document Text

Show stored source text (verify against official source)
AD Final Rules - DRS_46-38-02.html
Copy URL
Print/Save as PDF
Document Versions
 Feedback
Details
AD Number:
46-38-02
Document Type:
AD Final Rules
Docket Number:
Unknown
Subject Heading:
Airworthiness Directives; ERCO Model 415-C, -CD and -D Aircraft
Subject:
Aileron control stop
Status:
Current
Citation:
This information is not available.
Citation Publish Date:
Effective Date:
Make:
Univair Aircraft Corporation
Model:
415-C | 415-CD | 415-D
Product Type:
Aircraft
Product Subtype:
Small Airplane
Affected AD:
Superseded AD:
Affected By:
Superseded By:
Service/Office:
Office of Primary Responsibility:
CFR Part Reference:
Part 39
Comments:
AIRWORTHINESS DIRECTIVES FINAL RULES: 46-38-02
CITATION:   This information is not available.

PAGE NUMBER:  

DOCKET NUMBER:   Unknown

AMENDMENT:  

AD NUMBER:   46-38-02

SUBJECT HEADING:   Airworthiness Directives; ERCO Model 415-C, -CD and -D Aircraft

ACTION:  

SUMMARY:  

DATES:  

ADDRESSES:  

FOR FURTHER INFORMATION CONTACT:  

SUPPLEMENTARY INFORMATION:  

REGULATORY TEXT:   46-38-02 ERCO: (Was Mandatory Note 8 of AD-718-6.) Applies to 415-C, -CD and -D Aircraft Serial Numbers 113 to 2706 Except 2683, 2685, 2687, and 2691.
Compliance required prior to November 1, 1946.
(a) To provide additional bearing area and more positive locking action for the aileron control stop adjustment screw, add an AN 315-3R nut on the adjustment screw at the forward side of the stops and a star type AN 936-B10 lock washer (external teeth) between the jam nut and rear side of stops (Ercoupe P/N 415-52145).
(b) Inspect the welds which attach the aileron control stops to the control column cross member carefully for cracks. Also determine that welds are complete around the ends of the stops. Repair if cracked welds or insufficient welds are found.
(c) Inspect the adjustment of the two upper turnbuckles in the chain and cable system to be certain these turnbuckles do not touch the sprockets before the quadrant touches the stops. Readjust all three turnbuckles if necessary to insure freedom from this turnbuckle-sprocket interference.
(Erco Service Department Bulletin No. 13 covers this same subject.)

FOOTER:

Source: Official FAA Source ↗

Retrieved: Apr 8, 2026

Rights: U.S. Government Public Domain

This site is not affiliated with or endorsed by the FAA. Always verify with official sources.