AD 2021-10-04

[Federal Register Volume 86, Number 81 (Thursday, April 29, 2021)]
[Rules and Regulations]
[Pages 22584-22586]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2021-09082]



[[Page 22584]]

=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2021-0345; Project Identifier MCAI-2021-00479-T; 
Amendment 39-21537; AD 2021-10-04]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for all 
Airbus SAS Model A318, A319, A320, and A321 series airplanes. This AD 
was prompted by a potential quality issue in the fuel pump that 
includes a locking key of the impeller drive shaft found loose in the 
cavity under the impeller. This AD requires replacement of affected 
fuel pumps, as specified in a European Union Aviation Safety Agency 
(EASA) AD, which is incorporated by reference. The FAA is issuing this 
AD to address the unsafe condition on these products.

DATES: This AD becomes effective April 29, 2021.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of April 29, 
2021.
    The FAA must receive comments on this AD by June 14, 2021.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
    <bullet> Federal eRulemaking Portal: Go to <a href="https://www.regulations.gov">https://www.regulations.gov</a>. Follow the instructions for submitting comments.
    <bullet> Fax: 202-493-2251.
    <bullet> Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
    <bullet> Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590, between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays.
    For material incorporated by reference (IBR) in this AD, contact 
EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
8999 000; email <a href="/cdn-cgi/l/email-protection#3d7c794e7d585c4e5c1358484f524d5c135848"><span class="__cf_email__" data-cfemail="96d7d2e5d6f3f7e5f7b8f3e3e4f9e6f7b8f3e3">[email&#160;protected]</span></a>; internet www.easa.europa.eu. You 
may find this IBR material on the EASA website at <a href="https://ad.easa.europa.eu">https://ad.easa.europa.eu</a>. You may view this IBR material at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 South 
216th St., Des Moines, WA. For information on the availability of this 
material at the FAA, call 206-231-3195. It is also available in the AD 
docket on the internet at <a href="https://www.regulations.gov">https://www.regulations.gov</a> by searching for 
and locating Docket No. FAA-2021-0345.

Examining the AD Docket

    You may examine the AD docket on the internet at <a href="https://www.regulations.gov">https://www.regulations.gov</a> by searching for and locating Docket No. FAA-2021-
0345; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this AD, any comments received, and other information. The street 
address for Docket Operations is listed above.

FOR FURTHER INFORMATION CONTACT: Sanjay Ralhan, Aerospace Engineer, 
Large Aircraft Section, International Validation Branch, FAA, 2200 
South 216th St., Des Moines, WA 98198; telephone and fax 206-231-3223; 
email <a href="/cdn-cgi/l/email-protection#eebd8f80848f97c0bc8f82868f80ae888f8fc0898198"><span class="__cf_email__" data-cfemail="99caf8f7f3f8e0b7cbf8f5f1f8f7d9fff8f8b7fef6ef">[email&#160;protected]</span></a>.

SUPPLEMENTARY INFORMATION:

Background

    EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA Emergency AD 2021-0115-E, dated April 
23, 2021 (EASA AD 2021-0115-E) (also referred to as the Mandatory 
Continuing Airworthiness Information, or the MCAI), to correct an 
unsafe condition for all Airbus SAS Model A318, A319, A320, and A321 
series airplanes. Model A320-215 airplanes, which are listed in the 
applicability of EASA AD 2021-0115-E, are not certificated by the FAA 
and are not included on the U.S. type certificate data sheet; this AD 
therefore does not include those airplanes in the applicability.
    This AD was prompted by the identification of a potential quality 
issue found in the fuel pump that includes a locking key of the 
impeller drive shaft found loose in the cavity under the impeller. 
Incorrect installation of the locking key combined with a pump 
operation not fully immersed in fuel could compromise the fuel pump 
integrity. The FAA is issuing this AD to address this condition, which, 
in the case of operating a pump while not fully immersed in fuel, could 
create an ignition source in the fuel tank, and result in a fuel tank 
explosion and consequent loss of the airplane. See the MCAI for 
additional background information.

Related Service Information Under 1 CFR Part 51

    EASA AD 2021-0115-E specifies procedures for replacement of 
affected fuel pumps. This service information is reasonably available 
because the interested parties have access to it through their normal 
course of business or by the means identified in the ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to the FAA's bilateral agreement with the State of Design Authority, 
the FAA has been notified of the unsafe condition described in the MCAI 
referenced above. The FAA is issuing this AD because the FAA evaluated 
all pertinent information and determined the unsafe condition exists 
and is likely to exist or develop on other products of the same type 
design.

Requirements of This AD

    This AD requires accomplishing the actions specified in EASA AD 
2021-0115-E described previously, as incorporated by reference, except 
for any differences identified as exceptions in the regulatory text of 
this AD.
    The service information referenced in EASA AD 2021-0115-E includes 
a number of ``RC'' (required for compliance) steps. This AD, however, 
does not require those RC steps, and requires that the replacement be 
done as specified in paragraph (h)(2) of this AD.
    The service information referenced in EASA AD 2021-0115-E specifies 
reporting certain information and sending affected fuel pumps to the 
manufacturer. Those actions are not required by this AD, although the 
FAA recommends that those actions be performed as identified in the 
service information.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA initially worked with Airbus and EASA to develop a 
process to use certain EASA ADs as the primary source of information 
for compliance with requirements for corresponding FAA ADs. The FAA has 
since coordinated with other manufacturers and civil aviation 
authorities (CAAs) to use this process. As a result, EASA AD 2021-0115-
E is incorporated by reference in this final rule. This AD,

[[Page 22585]]

therefore, requires compliance with EASA AD 2021-0115-E in its 
entirety, through that incorporation, except for any differences 
identified as exceptions in the regulatory text of this AD. Using 
common terms that are the same as the heading of a particular section 
in the EASA AD does not mean that operators need comply only with that 
section. For example, where the AD requirement refers to ``all required 
actions and compliance times,'' compliance with this AD requirement is 
not limited to the section titled ``Required Action(s) and Compliance 
Time(s)'' in the EASA AD. Service information specified in EASA AD 
2021-0115-E that is required for compliance with EASA AD 2021-0115-E is 
available on the internet at <a href="https://www.regulations.gov">https://www.regulations.gov</a> by searching 
for and locating Docket No. FAA-2021-0345.

Justification for Immediate Adoption and Determination of the Effective 
Date

    Section 553(b)(3)(B) of the Administrative Procedure Act (APA) (5 
U.S.C. 551 et seq.) authorizes agencies to dispense with notice and 
comment procedures for rules when the agency, for ``good cause,'' finds 
that those procedures are ``impracticable, unnecessary, or contrary to 
the public interest.'' Under this section, an agency, upon finding good 
cause, may issue a final rule without providing notice and seeking 
comment prior to issuance. Further, section 553(d) of the APA 
authorizes agencies to make rules effective in less than thirty days, 
upon a finding of good cause.
    An unsafe condition exists that requires the immediate adoption of 
this AD without providing an opportunity for public comments prior to 
adoption. The FAA has found that the risk to the flying public 
justifies forgoing notice and comment prior to adoption of this rule 
because of a potential quality issue in the fuel pump, including a 
locking key of the impeller drive shaft that was found loose in the 
cavity under the impeller. This condition, if combined with a pump 
operating while not fully immersed in fuel, could create an ignition 
source in the fuel tank. Operating with a combination of these 
conditions could result in a fuel tank explosion and consequent loss of 
the airplane. Accordingly, notice and opportunity for prior public 
comment are impracticable and contrary to the public interest pursuant 
to 5 U.S.C. 553(b)(3)(B).
    In addition, the FAA finds that good cause exists pursuant to 5 
U.S.C. 553(d) for making this amendment effective in less than 30 days, 
for the same reasons the FAA found good cause to forgo notice and 
comment.

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this AD. Send your comments to an address listed under 
ADDRESSES. Include ``Docket No. FAA-2021-0345; Project Identifier MCAI-
2021-00479-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the final rule, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
this final rule because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
<a href="https://www.regulations.gov">https://www.regulations.gov</a>, including any personal information you 
provide. The agency will also post a report summarizing each 
substantive verbal contact received about this final rule.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this AD contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this AD, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this AD. Submissions containing CBI should be sent to Sanjay 
Ralhan, Aerospace Engineer, Large Aircraft Section, International 
Validation Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; 
telephone and fax 206-231-3223; email <a href="/cdn-cgi/l/email-protection#1d4e7c73777c64334f7c71757c735d7b7c7c337a726b"><span class="__cf_email__" data-cfemail="0251636c68637b2c50636e6a636c426463632c656d74">[email&#160;protected]</span></a>. Any 
commentary that the FAA receives which is not specifically designated 
as CBI will be placed in the public docket for this rulemaking.

Regulatory Flexibility Act (RFA)

    The requirements of the RFA do not apply when an agency finds good 
cause pursuant to 5 U.S.C. 553 to adopt a rule without prior notice and 
comment. Because the FAA has determined that it has good cause to adopt 
this rule without notice and comment, RFA analysis is not required.

Costs of Compliance

    The FAA estimates that this AD affects 1,728 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
6 work-hours x $85 per hour = $510...........................             $ *             $510         $881,280
----------------------------------------------------------------------------------------------------------------
* According to the manufacturer, all parts costs of this AD are covered under warranty.

    The FAA has included all known costs in its cost estimate. 
According to the manufacturer, however, some or all of the costs of 
this AD may be covered under warranty, thereby reducing the cost impact 
on affected operators.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or

[[Page 22586]]

develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this AD will not have federalism 
implications under Executive Order 13132. This AD will not have a 
substantial direct effect on the States, on the relationship between 
the national government and the States, or on the distribution of power 
and responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866, and
    (2) Will not affect intrastate aviation in Alaska.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

2021-10-04 Airbus SAS: Amendment 39-21537; Docket No. FAA-2021-0345; 
Project Identifier MCAI-2021-00479-T.

(a) Effective Date

    This airworthiness directive (AD) becomes effective April 29, 
2021.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to the Airbus SAS airplanes, certificated in any 
category and identified in paragraphs (c)(1) through (4) of this AD.
    (1) All Model A318-111, A318-112, A318-121, and A318-122 
airplanes.
    (2) All Model A319-111, A319-112, A319-113, A319-114, A319-115, 
A319-131, A319-132, A319-133, A319-151N, A319-153N, and A319-171N 
airplanes.
    (3) All Model A320-211, A320-212, A320-214, A320-216, A320-231, 
A320-232, A320-233, A320-251N, A320-252N, A320-253N, A320-271N, 
A320-272N, and A320-273N airplanes.
    (4) All Model A321-111, A321-112, A321-131, A321-211, A321-212, 
A321-213, A321-231, A321-232, A321-251N, A321-251NX, A321-252N, 
A321-252NX, A321-253N, A321-253NX, A321-271N, A321-271NX, A321-272N, 
and A321-272NX airplanes.

(d) Subject

    Air Transport Association (ATA) of America Code 28, Fuel.

(e) Reason

    This AD was prompted by a potential quality issue in the fuel 
pump that includes a locking key of the impeller drive shaft found 
loose in the cavity under the impeller. The FAA is issuing this AD 
to address this condition, which, if combined with a pump operating 
while not fully immersed in fuel, could create an ignition source in 
the fuel tank, and result in a fuel tank explosion and consequent 
loss of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, European Union Aviation Safety Agency (EASA) 
Emergency AD 2021-0115-E, dated April 23, 2021 (EASA AD 2021-0115-
E).

(h) Exceptions to EASA AD 2021-0115-E

    (1) Where EASA AD 2021-0115-E refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) Where paragraph (1) of EASA AD 2021-0115-E specifies a 
method of accomplishment of certain actions, replace the text ``in 
accordance with the instructions of the AOT [Alert Operators 
Transmission]'' with ``in accordance with paragraph 4.2 of the 
AOT.''
    (3) Where paragraph (2) of EASA AD 2021-0115-E allows deferring 
the replacement ``in accordance with . . . Airbus DOA,'' this AD 
requires that those instructions be approved by the Manager, Large 
Aircraft Section, International Validation Branch, FAA; or EASA; or 
Airbus SAS's EASA Design Organization Approval (DOA). If approved by 
the DOA, the approval must include the DOA-authorized signature.
    (4) The ``Remarks'' section of EASA AD 2021-0115-E does not 
apply to this AD.

(i) No Reporting Requirement

    Although the service information referenced in EASA AD 2021-
0115-E specifies to submit certain information and return affected 
pumps to the manufacturer, this AD does not require those actions.

(j) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
Large Aircraft Section, International Validation Branch, FAA, has 
the authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or responsible Flight 
Standards Office, as appropriate. If sending information directly to 
the Large Aircraft Section, International Validation Branch, send it 
to the attention of the person identified in paragraph (k) of this 
AD. Information may be emailed to: <a href="/cdn-cgi/l/email-protection#596074180f0a7418100b746e6a69741814161a193f3838773e362f"><span class="__cf_email__" data-cfemail="dee7f39f888df39f978cf3e9edeef39f93919d9eb8bfbff0b9b1a8">[email&#160;protected]</span></a>. 
Before using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, Large Aircraft 
Section, International Validation Branch, FAA; or EASA; or Airbus 
SAS's EASA DOA. If approved by the DOA, the approval must include 
the DOA-authorized signature.

(k) Related Information

    For more information about this AD, contact Sanjay Ralhan, 
Aerospace Engineer, Large Aircraft Section, International Validation 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
and fax 206-231-3223; email <a href="/cdn-cgi/l/email-protection#ecbf8d82868d95c2be8d80848d82ac8a8d8dc28b839a"><span class="__cf_email__" data-cfemail="aefdcfc0c4cfd780fccfc2c6cfc0eec8cfcf80c9c1d8">[email&#160;protected]</span></a>.

(l) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) European Union Aviation Safety Agency (EASA) Emergency AD 
2021-0115-E, dated April 23, 2021.
    (ii) [Reserved]
    (3) For EASA AD 2021-0115-E, contact EASA, Konrad-Adenauer-Ufer 
3, 50668 Cologne, Germany; telephone +49 221 8999 000; email 
<a href="/cdn-cgi/l/email-protection#92d3d6e1d2f7f3e1f3bcf7e7e0fde2f3bcf7e7"><span class="__cf_email__" data-cfemail="1352576053767260723d7666617c63723d7666">[email&#160;protected]</span></a>; internet www.easa.europa.eu. You may find this 
EASA AD on the EASA website at <a href="https://ad.easa.europa.eu">https://ad.easa.europa.eu</a>.
    (4) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., 
Des Moines, WA. For information on the availability of this material 
at the FAA, call 206-231-3195. This material may be found in the AD 
docket on the internet at <a href="https://www.regulations.gov">https://www.regulations.gov</a> by searching 
for and locating Docket No. FAA-2021-0345.
    (5) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, email 
<a href="/cdn-cgi/l/email-protection#a6c0c3c2d4c3c188cac3c1c7cae6c8c7d4c788c1c9d0"><span class="__cf_email__" data-cfemail="37515253455250195b5250565b775956455619505841">[email&#160;protected]</span></a>, or go to <a href="https://www.archives.gov/federal-register/cfr/ibr-locations.html">https://www.archives.gov/federal-register/cfr/ibr-locations.html</a>.

    Issued on April 27, 2021.
Gaetano A. Sciortino,
Deputy Director for Strategic Initiatives, Compliance & Airworthiness 
Division, Aircraft Certification Service.
[FR Doc. 2021-09082 Filed 4-27-21; 4:15 pm]
BILLING CODE 4910-13-P