AD 2019-21-05

[Federal Register Volume 84, Number 215 (Wednesday, November 6, 2019)]
[Rules and Regulations]
[Pages 59711-59713]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2019-24160]



========================================================================
Rules and Regulations
                                                Federal Register
________________________________________________________________________

This section of the FEDERAL REGISTER contains regulatory documents 
having general applicability and legal effect, most of which are keyed 
to and codified in the Code of Federal Regulations, which is published 
under 50 titles pursuant to 44 U.S.C. 1510.

The Code of Federal Regulations is sold by the Superintendent of Documents. 

========================================================================


Federal Register / Vol. 84, No. 215 / Wednesday, November 6, 2019 / 
Rules and Regulations

[[Page 59711]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2019-0718; Product Identifier 2019-NM-128-AD; Amendment 
39-19771; AD 2019-21-05]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for 
certain Airbus SAS Model A330-200, A330-200 Freighter, A330-300, A340-
200, A340-300, A340-500, and A340-600 series airplanes. This AD was 
prompted by reports that non-approved passenger oxygen containers 
(POCs) may have been installed on the affected airplanes. This AD 
requires a one-time special detailed inspection (SDI) of each POC, and 
replacement if necessary, as specified in a European Union Aviation 
Safety Agency (EASA) AD, which is incorporated by reference. The FAA is 
issuing this AD to address the unsafe condition on these products.

DATES: This AD becomes effective November 21, 2019.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of November 21, 
2019.
    The FAA must receive comments on this AD by December 23, 2019.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
    <bullet> Federal eRulemaking Portal: Go to <a href="https://www.regulations.gov">https://www.regulations.gov</a>. Follow the instructions for submitting comments.
    <bullet> Fax: 202-493-2251.
    <bullet> Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
    <bullet> Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590, between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays.
    For the material incorporated by reference (IBR) in this AD, 
contact the EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; 
telephone +49 221 89990 1000; email <a href="/cdn-cgi/l/email-protection#6120251221040012004f0414130e11004f0414"><span class="__cf_email__" data-cfemail="1554516655707466743b7060677a65743b7060">[email&#160;protected]</span></a>; internet 
www.easa.europa.eu. You may find this IBR material on the EASA website 
at <a href="https://ad.easa.europa.eu">https://ad.easa.europa.eu</a>. You may view this IBR material at the 
FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. 
For information on the availability of this material at the FAA, call 
206-231-3195. It is also available in the AD docket on the internet at 
<a href="https://www.regulations.gov">https://www.regulations.gov</a> by searching for and locating Docket No. 
FAA-2019-0718.

Examining the AD Docket

    You may examine the AD docket on the internet at <a href="https://www.regulations.gov">https://www.regulations.gov</a> by searching for and locating Docket No. FAA-2019-
0718; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this AD, the regulatory evaluation, any comments received, and other 
information. The street address for Docket Operations is listed above. 
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Vladimir Ulyanov, Aerospace Engineer, 
International Section, Transport Standards Branch, FAA, 2200 South 
216th St., Des Moines, WA 98198; telephone and fax 206-231-3229.

SUPPLEMENTARY INFORMATION: 

Discussion

    The EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2019-0176, dated July 19, 2019 
(``EASA AD 2019-0176'') (also referred to as the Mandatory Continuing 
Airworthiness Information, or ``the MCAI''), to correct an unsafe 
condition for certain Airbus SAS Model A330-200, A330-200 Freighter, 
A330-300, A340-200, A340-300, A340-500, and A340-600 series airplanes.
    This AD was prompted by reports that non-approved POCs may have 
been installed on the affected airplanes. The FAA is issuing this AD to 
address possible non-approved POC installation, which could lead to 
reduced available oxygen capacity, possibly resulting in injury to 
airplane occupants following a depressurization event. See the MCAI for 
additional background information.

Related IBR Material Under 1 CFR Part 51

    EASA AD 2019-0176 describes procedures for performing a one-time 
SDI of each POC and, depending on findings, replacement with a 
serviceable part.
    This material is reasonably available because the interested 
parties have access to it through their normal course of business or by 
the means identified in the ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to a bilateral agreement with the State of Design Authority, the FAA 
has been notified of the unsafe condition described in the MCAI 
referenced above. The FAA is issuing this AD because we evaluated all 
pertinent information and determined the unsafe condition exists and is 
likely to exist or develop on other products of the same type design.

Requirements of This AD

    This AD requires accomplishing the actions specified in the EASA AD 
described previously, as incorporated by reference, except for any 
differences identified as exceptions in the regulatory text of this AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA initially worked with Airbus and EASA to develop a 
process to use certain EASA ADs as the primary source of information 
for compliance with requirements for corresponding FAA ADs. The FAA has 
since coordinated with other manufacturers and civil aviation 
authorities (CAAs) to

[[Page 59712]]

use this process. As a result, EASA AD 2019-0176 will be incorporated 
by reference in the FAA final rule. This AD, therefore, requires 
compliance with EASA AD 2019-0176 in its entirety, through that 
incorporation, except for any differences identified as exceptions in 
the regulatory text of this AD. Using common terms that are the same as 
the heading of a particular section in the EASA AD does not mean that 
operators need comply only with that section. For example, where the AD 
requirement refers to ``all required actions and compliance times,'' 
compliance with this AD requirement is not limited to the section 
titled ``Required Action(s) and Compliance Time(s)'' in the EASA AD. 
Service information specified in EASA AD 2019-0176 that is required for 
compliance with EASA AD 2019-0176 will be available on the internet at 
<a href="https://www.regulations.gov">https://www.regulations.gov</a> by searching for and locating Docket No. 
FAA-2019-0718, after the FAA final rule is published.

FAA's Justification and Determination of the Effective Date

    Since there are currently no domestic operators of these products, 
notice and opportunity for public comment before issuing this AD are 
unnecessary. In addition, for the reasons stated above, the FAA finds 
that good cause exists for making this amendment effective in less than 
30 days.

Comments Invited

    This AD is a final rule that involves requirements affecting flight 
safety, and the FAA did not precede it by notice and opportunity for 
public comment. The FAA invites you to send any written relevant data, 
views, or arguments about this AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2019-0718; 
Product Identifier 2019-NM-128-AD'' at the beginning of your comments. 
The FAA specifically invites comments on the overall regulatory, 
economic, environmental, and energy aspects of this AD. The FAA will 
consider all comments received by the closing date and may amend this 
AD based on those comments.
    The FAA will post all comments received, without change, to <a href="https://www.regulations.gov">https://www.regulations.gov</a>, including any personal information you provide. 
The FAA will also post a report summarizing each substantive verbal 
contact received about this AD.

Costs of Compliance

    Currently, there are no affected U.S.-registered airplanes. If an 
affected airplane is imported and placed on the U.S. Register in the 
future, the FAA will provide the following cost estimates to comply 
with this AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                                     Cost per
                                  Labor cost                                       Parts cost        product
----------------------------------------------------------------------------------------------------------------
1 work-hour x $85 per hour = $85..............................................              $0              $85
----------------------------------------------------------------------------------------------------------------

    The FAA estimates the following costs to do any necessary on-
condition actions that would be required based on the results of any 
required actions. The FAA has no way of determining the number of 
aircraft that might need this on-condition action:

                                     Estimated Costs of On-Condition Actions
----------------------------------------------------------------------------------------------------------------
                                                                                                     Cost per
                                  Labor cost                                       Parts cost        product
----------------------------------------------------------------------------------------------------------------
2 work-hours x $85 per hour = $170............................................             (*)           $170 *
----------------------------------------------------------------------------------------------------------------
* The FAA has received no definitive data that would enable the agency to provide parts cost estimates for the
  on-condition replacements specified in this AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This AD is issued in accordance with authority delegated by the 
Executive Director, Aircraft Certification Service, as authorized by 
FAA Order 8000.51C. In accordance with that order, issuance of ADs is 
normally a function of the Compliance and Airworthiness Division, but 
during this transition period, the Executive Director has delegated the 
authority to issue ADs applicable to transport category airplanes and 
associated appliances to the Director of the System Oversight Division.

Regulatory Findings

    The FAA determined that this AD will not have federalism 
implications under Executive Order 13132. This AD will not have a 
substantial direct effect on the States, on the relationship between 
the national government and the States, or on the distribution of power 
and responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

[[Page 59713]]

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2019-21-05 Airbus SAS: Amendment 39-19771; Docket No. FAA-2019-0718; 
Product Identifier 2019-NM-128-AD.

(a) Effective Date

    This AD becomes effective November 21, 2019.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Airbus SAS Model A330-200, A330-200 
Freighter, A330-300, A340-200, A340-300, A340-500, and A340-600 
series airplanes, certificated in any category, as identified in 
European Union Aviation Safety Agency (EASA) AD 2019-0176, dated 
July 19, 2019 (``EASA AD 2019-0176'').

(d) Subject

    Air Transport Association (ATA) of America Code 35, Oxygen.

(e) Reason

    This AD was prompted by reports that non-approved passenger 
oxygen containers (POCs) may have been installed on the affected 
airplanes. The FAA is issuing this AD to address possible non-
approved POC installation, which could lead to reduced available 
oxygen capacity, possibly resulting in injury to airplane occupants 
following a depressurization event.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, EASA AD 2019-0176.

(h) Exceptions to EASA AD 2019-0176

    (1) Where EASA AD 2019-0176 refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) The ``Remarks'' section of EASA AD 2019-0176 does not apply 
to this AD.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Section, Transport Standards Branch, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Section, send it to the attention of 
the person identified in paragraph (j) of this AD. Information may 
be emailed to: <a href="/cdn-cgi/l/email-protection#6d54402c2320405c5c5b402c20222e403f283c38283e393e2d0b0c0c430a021b"><span class="__cf_email__" data-cfemail="dee7f39f9093f3efefe8f39f93919df38c9b8f8b9b8d8a8d9eb8bfbff0b9b1a8">[email&#160;protected]</span></a>. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager of the local flight 
standards district office/certificate holding district office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Section, Transport Standards Branch, FAA; or EASA; or Airbus SAS's 
EASA Design Organization Approval (DOA). If approved by the DOA, the 
approval must include the DOA-authorized signature.
    (3) Required for Compliance (RC): For any service information 
referenced in EASA AD 2019-0176 that contains RC procedures and 
tests: Except as required by paragraph (i)(2) of this AD, RC 
procedures and tests must be done to comply with this AD; any 
procedures or tests that are not identified as RC are recommended. 
Those procedures and tests that are not identified as RC may be 
deviated from using accepted methods in accordance with the 
operator's maintenance or inspection program without obtaining 
approval of an AMOC, provided the procedures and tests identified as 
RC can be done and the airplane can be put back in an airworthy 
condition. Any substitutions or changes to procedures or tests 
identified as RC require approval of an AMOC.

(j) Related Information

    For more information about this AD, contact Vladimir Ulyanov, 
Aerospace Engineer, International Section, Transport Standards 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
and fax 206-231-3229.

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) European Union Aviation Safety Agency (EASA) AD 2019-0176, 
dated July 19, 2019.
    (ii) [Reserved]
    (3) For information about EASA AD 2019-0176, contact the EASA, 
at Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
89990 6017; email <a href="/cdn-cgi/l/email-protection#febfba8dbe9b9f8d9fd09b8b8c918e9fd09b8b"><span class="__cf_email__" data-cfemail="a0e1e4d3e0c5c1d3c18ec5d5d2cfd0c18ec5d5">[email&#160;protected]</span></a>; Internet www.easa.europa.eu. 
You may find this EASA AD on the EASA website at <a href="https://ad.easa.europa.eu">https://ad.easa.europa.eu</a>.
    (4) You may view this material at the FAA, Transport Standards 
Branch, 2200 South 216th St., Des Moines, WA. For information on the 
availability of this material at the FAA, call 206-231-3195. EASA AD 
2019-0176 may be found in the AD docket on the internet at <a href="https://www.regulations.gov">https://www.regulations.gov</a> by searching for and locating Docket No. FAA-
2019-0718.
    (5) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, email 
<a href="/cdn-cgi/l/email-protection#98fefdfceafdffb6f4fdfff9f4d8f6f9eaf9b6fff7ee"><span class="__cf_email__" data-cfemail="2f494a4b5d4a4801434a484e436f414e5d4e01484059">[email&#160;protected]</span></a>, or go to: <a href="https://www.archives.gov/federal-register/cfr/ibr-locations.html">https://www.archives.gov/federal-register/cfr/ibr-locations.html</a>.

    Issued in Des Moines, Washington, on October 18, 2019.
Dionne Palermo,
Acting Director, System Oversight Division, Aircraft Certification 
Service.
[FR Doc. 2019-24160 Filed 11-5-19; 8:45 am]
BILLING CODE 4910-13-P