AD 2019-03-29
Applicability
| Type | Manufacturer | Model | Details |
|---|---|---|---|
| aircraft | Bombardier Inc. | BD-100-1A10 (Challenger 300) | Airworthiness Directives; Bombardier, Inc., Airplanes |
Unsafe Condition
jamming of the steering selector valve (SSV) after independent failure of a second component of the nose wheel steering system, which could result in uncommanded nose wheel steering and a possible runway excursion.
AI-generated summary from the source AD text. Verify against the official source before acting.
Required Actions
modifying the left-hand hydraulic system of the NWS control system by installing a hydraulic filter into the hydraulic line between the direct current motor pump and the SSV and, for certain airplanes, torqueing the fittings on a certain tube assembly.
AI-generated summary from the source AD text. Verify against the official source before acting.
Compliance Time
Before further flight
AI-generated summary from the source AD text. Verify against the official source before acting.
Affected Aircraft
Bombardier, Inc., Model BD-100-1A10 airplanes, serial numbers 20720 and 20722 are exempt from the actions specified in paragraph (g) of this AD.
AI-generated summary from the source AD text. Verify against the official source before acting.
Federal Register Abstract
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc., Model BD-100-1A10 airplanes. This AD was prompted by an incident of uncommanded nose wheel steering (NWS) in-service; subsequent investigation revealed that the steering selector valve (SSV) is susceptible to jamming in the open position due to particulate contamination of the hydraulic system. This AD requires modifying the left-hand hydraulic system of the NWS control system and, for certain airplanes, torqueing the fittings on a certain tube assembly. We are issuing this AD to address the unsafe condition on these products.
Applicability Source Text
Show captured applicability text from the source AD
(c) Applicability
This AD applies to Bombardier, Inc., Model BD-100-1A10
airplanes, certificated in any category, serial numbers 20002
through 20744 inclusive.
Document Text
Show stored source text (verify against official source)
[Federal Register Volume 84, Number 85 (Thursday, May 2, 2019)]
[Rules and Regulations]
[Pages 18704-18707]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2019-08915]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2018-0792; Product Identifier 2018-NM-090-AD; Amendment
39-19581; AD 2019-03-29]
RIN 2120-AA64
Airworthiness Directives; Bombardier, Inc., Airplanes
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: We are adopting a new airworthiness directive (AD) for certain
Bombardier, Inc., Model BD-100-1A10 airplanes. This AD was prompted by
an incident of uncommanded nose wheel steering (NWS) in-service;
subsequent investigation revealed that the steering selector valve
(SSV) is susceptible to jamming in the open position due to particulate
contamination of the hydraulic system. This AD requires modifying the
left-hand hydraulic system of the NWS control system and, for certain
airplanes, torqueing the
[[Page 18705]]
fittings on a certain tube assembly. We are issuing this AD to address
the unsafe condition on these products.
DATES: This AD is effective June 6, 2019.
The Director of the Federal Register approved the incorporation by
reference of certain publications listed in this AD as of June 6, 2019.
ADDRESSES: For service information identified in this final rule,
contact Bombardier, Inc., 200 C[ocirc]te-Vertu Road West, Dorval,
Qu[eacute]bec H4S 2A3, Canada; North America toll-free telephone 1-866-
538-1247 or direct-dial telephone 1-514-855-2999; email
<a href="/cdn-cgi/l/email-protection#b9d8da97c0ccd5f9d8dccbd697dbd6d4dbd8cbddd0dccb97dad6d4"><span class="__cf_email__" data-cfemail="fc9d9fd2858990bc9d998e93d29e93919e9d8e9895998ed29f9391">[email protected]</span></a>; internet <a href="http://www.bombardier.com">http://www.bombardier.com</a>. You may
view this service information at the FAA, Transport Standards Branch,
2200 South 216th St., Des Moines, WA. For information on the
availability of this material at the FAA, call 206-231-3195. It is also
available on the internet at <a href="http://www.regulations.gov">http://www.regulations.gov</a> by searching
for and locating Docket No. FAA-2018-0792.
Examining the AD Docket
You may examine the AD docket on the internet at <a href="http://www.regulations.gov">http://www.regulations.gov</a> by searching for and locating Docket No. FAA-2018-
0792; or in person at Docket Operations between 9 a.m. and 5 p.m.,
Monday through Friday, except Federal holidays. The AD docket contains
this final rule, the regulatory evaluation, any comments received, and
other information. The address for Docket Operations (phone: 800-647-
5527) is U.S. Department of Transportation, Docket Operations, M-30,
West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE,
Washington, DC 20590.
FOR FURTHER INFORMATION CONTACT: Darren Gassetto, Aerospace Engineer,
Mechanical Systems and Administrative Services Section, FAA, New York
ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590;
telephone 516-228-7323; fax 516 794 5531; email <a href="/cdn-cgi/l/email-protection#0a33276b7c792764736b6965276965794a6c6b6b246d657c"><span class="__cf_email__" data-cfemail="437a6e2235306e2d3a22202c6e202c30032522226d242c35">[email protected]</span></a>.
SUPPLEMENTARY INFORMATION:
Discussion
We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR
part 39 by adding an AD that would apply to certain Bombardier, Inc.,
Model BD-100-1A10 airplanes. The NPRM published in the Federal Register
on September 17, 2018 (83 FR 46895). The NPRM was prompted by an
incident of uncommanded NWS in-service; subsequent investigation
revealed that the SSV is susceptible to jamming in the open position
due to particulate contamination of the hydraulic system. The NPRM
proposed to require modifying the left-hand hydraulic system of the NWS
control system and, for certain airplanes, torqueing the fittings on a
certain tube assembly.
We are issuing this AD to address jamming of the SSV after
independent failure of a second component of the NWS control system,
which could result in uncommanded NWS and a possible runway excursion.
Transport Canada Civil Aviation (TCCA), which is the aviation
authority for Canada, has issued Canadian AD CF-2018-11, dated April 5,
2018 (referred to after this as the Mandatory Continuing Airworthiness
Information, or ``the MCAI''), to correct an unsafe condition for
certain Bombardier, Inc., Model BD-100-1A10 airplanes. The MCAI states:
An incident of uncommanded nose wheel steering occurred in-
service. Subsequent investigation revealed that the steering
selector valve (SSV) was vulnerable to jamming in the open position
due to particulate contamination of the hydraulic system. If not
corrected, a jam of the SSV, following the independent failure of a
second component of the nose wheel steering system, could result in
uncommanded nose wheel steering and a risk of runway excursion.
This [Canadian] AD requires the incorporation of a hydraulic
fluid filter in the line supplying pressure from the direct current
motor pump to the nose wheel steering system [and, for certain
airplanes, torqueing the fittings on a certain tube assembly].
You may examine the MCAI in the AD docket on the internet at <a href="http://www.regulations.gov">http://www.regulations.gov</a> by searching for and locating Docket No. FAA-2018-
0792.
Comments
We gave the public the opportunity to participate in developing
this final rule. The following presents the comments received on the
NPRM and the FAA's response to each comment.
Request To Correct a Date for Receipt of Comments
Bombardier requested that we correct a typographical error in the
DATES section of the proposed AD. The proposed AD stated ``We must
receive comments on this proposed AD by November 1, 20181.'' Bombardier
noted that the sentence should state ``We must receive comments on this
proposed AD by November 1, 2018.''
We acknowledge this typographical error. However, the section
containing this statement does not get carried over to this final rule.
Therefore, we have not changed this AD regarding this issue.
Request To Update Contact Information
Bombardier requested that we update their contact information in
the ADDRESSES and Related Information sections of the proposed AD.
Bombardier noted that their email and street addresses changed recently
and updating them in our final rule would allow operators to contact
Bombardier with questions.
We agree with the commenter's request for the reasons stated. We
have updated the contact information for Bombardier in the ADDRESSES
section and paragraph (k)(3) of this AD.
Request To Provide an Exception to Certain Actions
NetJets requested that we provide an exception to paragraph (g) of
the proposed AD for airplanes having serial numbers 20720 and 20722.
NetJets noted that the actions specified in Bombardier Service Bulletin
350-32-007 were incorporated in accordance with Bombardier Service
Bulletin 350-32-007 on those airplanes during production. NetJets added
that the actions required by paragraph (h) of the proposed AD would
still apply to those airplanes.
We agree to clarify. Paragraph (g) of this AD only applies to
airplanes not identified in paragraph (h) of this AD. Any airplane that
has incorporated Bombardier Service Bulletin 350-32-007 dated January
4, 2018; Revision 01, dated January 23, 2018; or Revision 02, dated
March 14, 2018, as of the effective date of this AD must complete the
actions required by paragraph (h) in this AD, but does not have to
complete the actions specified in paragraph (g) of this AD. Therefore,
this AD has not been changed with regard to this request.
Conclusion
We reviewed the relevant data, considered the comments received,
and determined that air safety and the public interest require adopting
this final rule with the change described previously and minor
editorial changes. We have determined that these minor changes:
<bullet> Are consistent with the intent that was proposed in the
NPRM for addressing the unsafe condition; and
<bullet> Do not add any additional burden upon the public than was
already proposed in the NPRM.
We also determined that these changes will not increase the
economic burden on any operator or increase the scope of this final
rule.
[[Page 18706]]
Related Service Information Under 1 CFR Part 51
Bombardier has issued Service Bulletin 100-32-31, Revision 03; and
Service Bulletin 350-32-007, Revision 03; both dated March 27, 2018.
This service information describes procedures for modifying the left-
hand hydraulic system of the NWS control system by installing a
hydraulic filter into the hydraulic line between the direct current
motor pump and the SSV and, for certain airplanes, torqueing the
fittings on a certain tube assembly. These documents are distinct since
they apply to different airplane configurations.
This service information is reasonably available because the
interested parties have access to it through their normal course of
business or by the means identified in the ADDRESSES section.
Costs of Compliance
We estimate that this AD affects 534 airplanes of U.S. registry. We
estimate the following costs to comply with this AD:
Estimated Costs
----------------------------------------------------------------------------------------------------------------
Cost per Cost on U.S.
Labor cost Parts cost product operators
----------------------------------------------------------------------------------------------------------------
25 work-hours x $85 per hour = $2,125........................ $13,196 $15,321 $8,181,414
----------------------------------------------------------------------------------------------------------------
According to the manufacturer, some or all of the costs of this AD
may be covered under warranty, thereby reducing the cost impact on
affected individuals. We do not control warranty coverage for affected
individuals. As a result, we have included all known costs in our cost
estimate.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
This AD is issued in accordance with authority delegated by the
Executive Director, Aircraft Certification Service, as authorized by
FAA Order 8000.51C. In accordance with that order, issuance of ADs is
normally a function of the Compliance and Airworthiness Division, but
during this transition period, the Executive Director has delegated the
authority to issue ADs applicable to transport category airplanes and
associated appliances to the Director of the System Oversight Division.
Regulatory Findings
This AD will not have federalism implications under Executive Order
13132. This AD will not have a substantial direct effect on the States,
on the relationship between the national government and the States, or
on the distribution of power and responsibilities among the various
levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979),
(3) Will not affect intrastate aviation in Alaska, and
(4) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive (AD):
2019-03-29 Bombardier, Inc.: Amendment 39-19581; Docket No. FAA-
2018-0792; Product Identifier 2018-NM-090-AD.
(a) Effective Date
This AD is effective June 6, 2019.
(b) Affected ADs
None.
(c) Applicability
This AD applies to Bombardier, Inc., Model BD-100-1A10
airplanes, certificated in any category, serial numbers 20002
through 20744 inclusive.
(d) Subject
Air Transport Association (ATA) of America Code 32, Landing
Gear.
(e) Reason
This AD was prompted by an incident of uncommanded nose wheel
steering (NWS) in-service; subsequent investigation revealed that
the steering selector valve (SSV) is susceptible to jamming in the
open position due to particulate contamination of the hydraulic
system. We are issuing this AD to address jamming of the SSV after
independent failure of a second component of the NWS control system,
which could result in uncommanded NWS and a possible runway
excursion.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Modify Hydraulic System
Except for airplanes identified in paragraph (h) of this AD:
Within 2,000 flight cycles or 60 months after the effective date of
this AD, whichever occurs first, modify the left-hand hydraulic
system of the NWS control system by installing a hydraulic filter
into the hydraulic line between the direct current motor pump and
the SSV, in accordance with the Accomplishment Instructions of
Bombardier Service Bulletin 100-32-31, Revision 03; or Bombardier
Service Bulletin 350-32-007, Revision 03; both dated March 27, 2018;
as applicable.
(h) Additional Action for Certain Airplanes
For airplanes that have incorporated Bombardier Service Bulletin
100-32-31,
[[Page 18707]]
dated January 4, 2018; Bombardier Service Bulletin 100-32-31,
Revision 01, dated January 23, 2018; Bombardier Service Bulletin
100-32-31, Revision 02, dated March 14, 2018; Bombardier Service
Bulletin 350-32-007, dated January 4, 2018; Bombardier Service
Bulletin 350-32-007, Revision 01, dated January 23, 2018; or
Bombardier Service Bulletin 350-32-007, Revision 02, dated March 14,
2018; as applicable, as of the effective date of this AD: Within 50
flight hours after the effective date of this AD, torque the
fittings on any tube assembly having part number K1000070395-401, in
accordance with the ``Retroactive Action'' instructions of
Bombardier Service Bulletin 100-32-31, Revision 03, or Bombardier
Service Bulletin 350-32-007, Revision 03, both dated March 27, 2018,
as applicable.
(i) Other FAA AD Provisions
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, New
York ACO Branch, FAA, has the authority to approve AMOCs for this
AD, if requested using the procedures found in 14 CFR 39.19. In
accordance with 14 CFR 39.19, send your request to your principal
inspector or local Flight Standards District Office, as appropriate.
If sending information directly to the manager of the certification
office, send it to ATTN: Program Manager, Continuing Operational
Safety, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410,
Westbury, NY 11590; telephone 516-228-7300; fax 516-794-5531. Before
using any approved AMOC, notify your appropriate principal
inspector, or lacking a principal inspector, the manager of the
local flight standards district office/certificate holding district
office.
(2) Contacting the Manufacturer: For any requirement in this AD
to obtain corrective actions from a manufacturer, the action must be
accomplished using a method approved by the Manager, New York ACO
Branch, FAA; or Transport Canada Civil Aviation (TCCA); or
Bombardier, Inc.'s TCCA Design Approval Organization (DAO). If
approved by the DAO, the approval must include the DAO-authorized
signature.
(j) Related Information
(1) Refer to Mandatory Continuing Airworthiness Information
(MCAI) Canadian AD CF-2018-11, dated April 5, 2018, for related
information. This MCAI may be found in the AD docket on the internet
at <a href="http://www.regulations.gov">http://www.regulations.gov</a> by searching for and locating Docket
No. FAA-2018-0792.
(2) For more information about this AD, contact Darren Gassetto,
Aerospace Engineer, Mechanical Systems and Administrative Services
Section, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410,
Westbury, NY 11590; telephone 516-228-7323; fax 516-794-5531; email
<a href="/cdn-cgi/l/email-protection#2e17034f585d0340574f4d41034d415d6e484f4f00494158"><span class="__cf_email__" data-cfemail="043d29657277296a7d65676b29676b77446265652a636b72">[email protected]</span></a>.
(k) Material Incorporated by Reference
(1) The Director of the Federal Register approved the
incorporation by reference (IBR) of the service information listed
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this service information as applicable to do
the actions required by this AD, unless this AD specifies otherwise.
(i) Bombardier Service Bulletin 100-32-31, Revision 03, dated
March 27, 2018.
(ii) Bombardier Service Bulletin 350-32-007, Revision 03, dated
March 27, 2018.
(3) For service information identified in this AD, contact
Bombardier, Inc., 200 C[ocirc]te-Vertu Road West, Dorval,
Qu[eacute]bec H4S 2A3, Canada; North America toll-free telephone 1-
866-538-1247 or direct-dial telephone 1-514-855-2999; email
<a href="/cdn-cgi/l/email-protection#caaba9e4b3bfa68aabafb8a5e4a8a5a7a8abb8aea3afb8e4a9a5a7"><span class="__cf_email__" data-cfemail="375654194e425b77565245581955585a555645535e52451954585a">[email protected]</span></a>; internet <a href="http://www.bombardier.com">http://www.bombardier.com</a>.
(4) You may view this service information at the FAA, Transport
Standards Branch, 2200 South 216th St., Des Moines, WA. For
information on the availability of this material at the FAA, call
206-231-3195.
(5) You may view this service information that is incorporated
by reference at the National Archives and Records Administration
(NARA). For information on the availability of this material at
NARA, call 202-741-6030, or go to: <a href="http://www.archives.gov/federal-register/cfr/ibr-locations.html">http://www.archives.gov/federal-register/cfr/ibr-locations.html</a>.
Issued in Des Moines, Washington, on February 22, 2019.
Michael Kaszycki,
Acting Director, System Oversight Division, Aircraft Certification
Service.
[FR Doc. 2019-08915 Filed 5-1-19; 8:45 am]
BILLING CODE 4910-13-P
Source: Official FAA Source ↗
Retrieved: Apr 6, 2026
Rights: U.S. Government Public Domain
This site is not affiliated with or endorsed by the FAA. Always verify with official sources.