AD 2018-03-21
Applicability
| Type | Manufacturer | Model | Details |
|---|---|---|---|
| aircraft | Airbus SAS | A330-202 | Airworthiness Directives; Airbus Airplanes |
| aircraft | Airbus SAS | A330-203 | Airworthiness Directives; Airbus Airplanes |
| aircraft | Airbus SAS | A330-223 | Airworthiness Directives; Airbus Airplanes |
| aircraft | Airbus SAS | A330-243 | Airworthiness Directives; Airbus Airplanes |
Unsafe Condition
The air cooling rack is installed too close to the supply hose of a high rate fire extinguishing bottle, which could lead to chafing and loss of the Fire Extinguishing System for the Lower Deck Cargo Compartment.
AI-generated summary from the source AD text. Verify against the official source before acting.
Required Actions
Contact the FAA to obtain instructions for addressing the unsafe condition, and do the actions specified in those instructions, which include replacing the affected flexible hose assembly.
AI-generated summary from the source AD text. Verify against the official source before acting.
Compliance Time
Before further flight
AI-generated summary from the source AD text. Verify against the official source before acting.
Affected Aircraft
Airbus Model A330-202, -203, -223, and -243 airplanes, all manufacturer serial numbers which incorporate the Airbus modifications specified in paragraphs (c)(1), (c)(2), or (c)(3) of this AD; except those airplanes which incorporate Airbus modification 200195, or Airbus modification 40487 (in production modification for installation of Pacific-Scientific fire extinguisher bottles), or Airbus Service Bulletin A330-26-3013 (in-service modification for installation of Pacific-Scientific fire extinguisher bottles).
AI-generated summary from the source AD text. Verify against the official source before acting.
Federal Register Abstract
We are adopting a new airworthiness directive (AD) for certain Airbus Model A330-202, -203, -223, and -243 airplanes. This AD requires contacting the FAA to obtain instructions for addressing the unsafe condition on these products, and doing the actions specified in those instructions. This AD was prompted by a design review of the airplane configuration incorporating certain fire extinguisher bottles and an optional galley cooling rack installation, which revealed that the air cooling rack is installed too close to the supply hose of a high rate fire extinguishing bottle. We are issuing this AD to address the unsafe condition on these products.
Applicability Source Text
Show captured applicability text from the source AD
(c) Applicability
This AD applies to Airbus Model A330-202, -203, -223, and -243
airplanes, certificated in any category, all manufacturer serial
numbers which incorporate the Airbus modifications specified in
paragraphs (c)(1), (c)(2), or (c)(3) of this AD; except those
airplanes which incorporate Airbus modification 200195, or Airbus
modification 40487 (in production modification for installation of
Pacific-Scientific fire extinguisher bottles), or Airbus Service
Bulletin A330-26-3013 (in-service modification for installation of
Pacific-Scientific fire extinguisher bottles).
(1) Airbus modification 45785.
(2) Airbus modification 45883.
(3) Airbus modification 46616.
Document Text
Show stored source text (verify against official source)
[Federal Register Volume 83, Number 29 (Monday, February 12, 2018)]
[Rules and Regulations]
[Pages 5902-5904]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2018-02750]
[[Page 5902]]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2018-0076; Product Identifier 2013-NM-227-AD; Amendment
39-19194; AD 2018-03-21]
RIN 2120-AA64
Airworthiness Directives; Airbus Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule; request for comments.
-----------------------------------------------------------------------
SUMMARY: We are adopting a new airworthiness directive (AD) for certain
Airbus Model A330-202, -203, -223, and -243 airplanes. This AD requires
contacting the FAA to obtain instructions for addressing the unsafe
condition on these products, and doing the actions specified in those
instructions. This AD was prompted by a design review of the airplane
configuration incorporating certain fire extinguisher bottles and an
optional galley cooling rack installation, which revealed that the air
cooling rack is installed too close to the supply hose of a high rate
fire extinguishing bottle. We are issuing this AD to address the unsafe
condition on these products.
DATES: This AD becomes effective February 27, 2018.
We must receive comments on this AD by March 29, 2018.
ADDRESSES: You may send comments, using the procedures found in 14 CFR
11.43 and 11.45, by any of the following methods:
<bullet> Federal eRulemaking Portal: Go to <a href="http://www.regulations.gov">http://www.regulations.gov</a>. Follow the instructions for submitting comments.
<bullet> Fax: 202-493-2251.
<bullet> Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE, Washington, DC 20590.
<bullet> Hand Delivery: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE, Washington, DC, between 9 a.m. and 5 p.m., Monday
through Friday, except Federal holidays.
Examining the AD Docket
You may examine the AD docket on the internet at <a href="http://www.regulations.gov">http://www.regulations.gov</a> by searching for and locating Docket No. FAA-2018-
0076; or in person at the Docket Operations office between 9 a.m. and 5
p.m., Monday through Friday, except Federal holidays. The AD docket
contains this AD, the regulatory evaluation, any comments received, and
other information. The street address for the Docket Operations office
(telephone: 800-647-5527) is in the ADDRESSES section. Comments will be
available in the AD docket shortly after receipt.
FOR FURTHER INFORMATION CONTACT: Vladimir Ulyanov, Aerospace Engineer,
International Section, Transport Standards Branch, FAA, 1601 Lind
Avenue SW, Renton, WA 98057-3356; telephone: 425-227-1138; fax: 425-
227-1149.
SUPPLEMENTARY INFORMATION:
Discussion
The European Aviation Safety Agency (EASA), which is the Technical
Agent for the Member States of the European Union, has issued EASA AD
2014-0248, dated November 19, 2014 (referred to after this as the
Mandatory Continuing Airworthiness Information, or ``the MCAI''), to
correct an unsafe condition for certain Airbus Model A330-202, -203, -
223, and -243 airplanes. The MCAI states:
During a design review of aeroplane configuration incorporating
Kidde fire extinguisher bottles and optional galley cooling rack
installation, it was identified that the air cooling rack is
installed too close to the supply hose of the high rated fire
extinguishing bottle in the area of frame (FR)34. Inadequate
physical separation between the flexible hose and the air cooling
rack could lead to chafing, likely resulting in loss of the Fire
Extinguishing System for the Lower Deck Cargo Compartment.
This condition, if not corrected, could lead, in case of fire,
to an uncontrolled fire in the cargo compartment, which could
ultimately jeopardise the aeroplane's safe flight.
To address this unsafe condition, Airbus developed an improved
flexible hose assembly (Airbus mod 200195, available for in-service
aeroplanes through Airbus SB A330-26-3046) and EASA issued AD 2013-
0250 (later revised) to require replacement of Part Number (P/N) P/N
A2627045200000 flexible hose assembly of the Fire Extinguisher
System at FR34.
Since EASA AD 2013-0250R1 was issued, it was discovered that
another flexible hose assembly, P/N A2627045400200, is also affected
by this chafing issue.
Prompted by this finding, Airbus issued SB A330-26-3046 Revision
02 to incorporate this additional affected P/N and to provide
additional work instructions for aeroplanes which accomplished the
SB at a previous revision.
For the reasons described above, this [EASA] AD retains the
requirements of EASA AD 2013-0250R1, which is superseded, and
requires additional work on aeroplanes that have already been
modified in accordance with the instructions of the original issue
or Revision 01 of the SB.
You may examine the MCAI on the internet at <a href="http://www.regulations.gov">http://www.regulations.gov</a> by searching for and locating Docket No. FAA-2018-
0076.
FAA's Determination and Requirements of This AD
This product has been approved by the aviation authority of another
country, and is approved for operation in the United States. Pursuant
to our bilateral agreement with the State of Design Authority, we have
been notified of the unsafe condition described in the MCAI. We are
issuing this AD because we evaluated all pertinent information and
determined the unsafe condition exists and is likely to exist or
develop on other products of the same type design.
FAA's Determination of the Effective Date
Since there are currently no domestic operators of this product, we
find good cause that notice and opportunity for prior public comment
are unnecessary. In addition, for the reason(s) stated above, we find
that good cause exists for making this amendment effective in less than
30 days.
Comments Invited
This AD is a final rule that involves requirements affecting flight
safety, and we did not precede it by notice and opportunity for public
comment. We invite you to send any written relevant data, views, or
arguments about this AD. Send your comments to an address listed under
the ADDRESSES section. Include ``Docket No. FAA-2018-0076; Product
Identifier 2013-NM-227-AD'' at the beginning of your comments. We
specifically invite comments on the overall regulatory, economic,
environmental, and energy aspects of this AD. We will consider all
comments received by the closing date and may amend this AD based on
those comments.
We will post all comments we receive, without change, to <a href="http://www.regulations.gov">http://www.regulations.gov</a>, including any personal information you provide. We
will also post a report summarizing each substantive verbal contact we
receive about this AD.
Costs of Compliance
Currently, there are no affected U.S.-registered airplanes. This AD
requires contacting the FAA to obtain instructions for addressing the
unsafe condition, and doing the actions specified in those
instructions. Based on the actions specified in the MCAI AD, we are
providing the following cost
[[Page 5903]]
estimates for an affected airplane that is placed on the U.S. Register
in the future:
Estimated Costs
----------------------------------------------------------------------------------------------------------------
Cost per
Action Labor cost Parts cost product
----------------------------------------------------------------------------------------------------------------
Modification............................... 6 work-hours x $85 per hour = $510. $399 $909
----------------------------------------------------------------------------------------------------------------
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. ``Subtitle VII: Aviation
Programs,'' describes in more detail the scope of the Agency's
authority.
We are issuing this rulemaking under the authority described in
``Subtitle VII, Part A, Subpart III, Section 44701: General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
This AD is issued in accordance with authority delegated by the
Executive Director, Aircraft Certification Service, as authorized by
FAA Order 8000.51C. In accordance with that order, issuance of ADs is
normally a function of the Compliance and Airworthiness Division, but
during this transition period, the Executive Director has delegated the
authority to issue ADs applicable to transport category airplanes to
the Director of the System Oversight Division.
Regulatory Findings
We determined that this AD will not have federalism implications
under Executive Order 13132. This AD will not have a substantial direct
effect on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
1. Is not a ``significant regulatory action'' under Executive Order
12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979);
3. Will not affect intrastate aviation in Alaska; and
4. Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive (AD):
2018-03-21 Airbus: Amendment 39-19194; Docket No. FAA-2018-0076;
Product Identifier 2013-NM-227-AD.
(a) Effective Date
This AD becomes effective February 27, 2018.
(b) Affected ADs
None.
(c) Applicability
This AD applies to Airbus Model A330-202, -203, -223, and -243
airplanes, certificated in any category, all manufacturer serial
numbers which incorporate the Airbus modifications specified in
paragraphs (c)(1), (c)(2), or (c)(3) of this AD; except those
airplanes which incorporate Airbus modification 200195, or Airbus
modification 40487 (in production modification for installation of
Pacific-Scientific fire extinguisher bottles), or Airbus Service
Bulletin A330-26-3013 (in-service modification for installation of
Pacific-Scientific fire extinguisher bottles).
(1) Airbus modification 45785.
(2) Airbus modification 45883.
(3) Airbus modification 46616.
(d) Subject
Air Transport Association (ATA) of America Code 26, Fire
protection.
(e) Reason
This AD was prompted by a design review of the airplane
configuration incorporating Kidde fire extinguisher bottles and an
optional galley cooling rack installation, which revealed that the
air cooling rack is installed too close to the supply hose of the
high rate fire extinguishing bottle in the area of frame (FR) 34. We
are issuing this AD to detect and correct inadequate physical
separation between the flexible supply hose and the air cooling rack
and consequent chafing and possible loss of the fire extinguishing
system for the lower deck cargo compartment. Such a condition could
result in an uncontrolled fire in the cargo compartment.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Required Action(s)
Within 30 days after the effective date of this AD, request
instructions from the Manager, International Section, Transport
Standards Branch, FAA, to address the unsafe condition specified in
paragraph (e) of this AD; and accomplish the actions at the times
specified in, and in accordance with, those instructions. Guidance
can be found in Mandatory Continuing Airworthiness Information
(MCAI) European Aviation Safety Agency (EASA) AD 2014-0248, dated
November 19, 2014.
(h) Alternative Methods of Compliance (AMOCs)
The Manager, International Section, Transport Standards Branch,
FAA, has the authority to approve AMOCs for this AD, if requested
using the procedures found in 14 CFR 39.19. In accordance with 14
CFR 39.19, send your request to your principal inspector or local
Flight Standards District Office, as appropriate. If sending
information directly to the International Section, send it to the
attention of the person identified in paragraph (i)(2) of this AD.
Information may be emailed to: <a href="/cdn-cgi/l/email-protection#8cb5a1cdc2c1a1bdbdbaa1cdc1c3cfa1dec9ddd9c9dfd8dfcceaededa2ebe3fa"><span class="__cf_email__" data-cfemail="2d14006c6360001c1c1b006c60626e007f687c78687e797e6d4b4c4c034a425b">[email protected]</span></a>.
Before using any approved AMOC, notify your appropriate principal
inspector, or lacking a principal inspector, the manager of the
local flight standards district office/certificate holding district
office.
(i) Related Information
(1) Refer to MCAI EASA AD 2014-0248, dated November 19, 2014,
for related information. You may examine the MCAI on the internet at
<a href="http://www.regulations.gov">http://www.regulations.gov</a> by searching for and locating Docket No.
FAA-2018-0076.
[[Page 5904]]
(2) For more information about this AD, contact Vladimir
Ulyanov, Aerospace Engineer, International Section, Transport
Standards Branch, FAA, 1601 Lind Avenue SW, Renton, WA 98057-3356;
telephone: 425-227-1138; fax: 425-227-1149.
(j) Material Incorporated by Reference
None.
Issued in Renton, Washington, on February 2, 2018.
Michael Kaszycki,
Acting Director, System Oversight Division, Aircraft Certification
Service.
[FR Doc. 2018-02750 Filed 2-9-18; 8:45 am]
BILLING CODE 4910-13-P
Source: Official FAA Source ↗
Retrieved: Apr 6, 2026
Rights: U.S. Government Public Domain
This site is not affiliated with or endorsed by the FAA. Always verify with official sources.