AD 2015-17-12

[Federal Register Volume 80, Number 164 (Tuesday, August 25, 2015)]
[Rules and Regulations]
[Pages 51443-51447]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2015-20692]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2014-1044; Directorate Identifier 2014-NM-148-AD; 
Amendment 39-18245; AD 2015-17-12]
RIN 2120-AA64


Airworthiness Directives; Cessna Aircraft Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for certain 
Cessna Aircraft Company Model 500, 501, 550, 551, S550, 560, and 650 
airplanes. This AD was prompted by reports of smoke and/or fire in the 
tailcone caused by sparking due to excessive wear of the brushes in the 
air conditioning (A/C) motor. This AD requires inspections to determine 
if certain A/C compressor motors are installed and to determine the 
accumulated hours on certain A/C compressor motor assemblies; and 
repetitive replacement of the brushes in the A/C compressor motor 
assembly, or, as an option to the brush replacement, deactivation of 
the A/C system and

[[Page 51444]]

placard installation; and return of replaced brushes to Cessna. We are 
issuing this AD to prevent the brushes in the A/C motor from wearing 
down beyond their limits, which could result in the rivet in the brush 
contacting the commutator, causing sparks and consequent fire and/or 
smoke in the tailcone with no means to detect or extinguish the fire 
and/or smoke.

DATES: This AD is effective September 29, 2015.
    The Director of the Federal Register approved the incorporation by 
reference of certain publications listed in this AD as of September 29, 
2015.

ADDRESSES: For service information identified in this AD, contact 
Cessna Aircraft Co., P.O. Box 7706, Wichita, KS 67277; phone: 316-517-
6215; fax: 316-517-5802; email: <a href="/cdn-cgi/l/email-protection#791a100d180d101617090c1b0a391a1c0a0a1718570d1c010d0b1617571a1614"><span class="__cf_email__" data-cfemail="1b78726f7a6f7274756b6e79685b787e6868757a356f7e636f69747535787476">[email&#160;protected]</span></a>; 
Internet <a href="https://www.cessnasupport.com/newlogin.html">https://www.cessnasupport.com/newlogin.html</a>. You may view this 
referenced service information at the FAA, Transport Airplane 
Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the 
availability of this material at the FAA, call 425-227-1221. It is also 
available on the Internet at <a href="http://www.regulations.gov">http://www.regulations.gov</a> by searching 
for and locating Docket No. FAA-2014-1044.

Examining the AD Docket

    You may examine the AD docket on the Internet at <a href="http://www.regulations.gov">http://www.regulations.gov</a> by searching for and locating Docket No. FAA-2014-
1044; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this AD, the regulatory evaluation, any comments received, and 
other information. The address for the Docket Office (phone: 800-647-
5527) is Docket Management Facility, U.S. Department of Transportation, 
Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 
New Jersey Avenue SE., Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: Craig Henrichsen, Aerospace Engineer, 
Electrical Systems and Avionics Branch, ACE-119W, FAA, Wichita Aircraft 
Certification Office (ACO), 1801 Airport Road, Room 100, Mid-Continent 
Airport, Wichita, KS 67209; phone: 316-946-4110; fax: 316-946-4107; 
email: <a href="/cdn-cgi/l/email-protection#0d4e7f6c646a234568637f646e657e68634d6b6c6c236a627b"><span class="__cf_email__" data-cfemail="abe8d9cac2cc85e3cec5d9c2c8c3d8cec5ebcdcaca85ccc4dd">[email&#160;protected]</span></a>.

SUPPLEMENTARY INFORMATION: 

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 by adding an AD that would apply to certain Cessna Aircraft 
Company Model 500, 501, 550, 551, S550, 560, and 650 airplanes. The 
NPRM published in the Federal Register on January 23, 2015 (80 FR 
3516). The NPRM was prompted by reports of smoke and/or fire in the 
tailcone caused by sparking due to excessive wear of the brushes in the 
A/C motor. The NPRM proposed to require inspections to determine if 
certain A/C compressor motors are installed and to determine the 
accumulated hours on certain A/C compressor motor assemblies; and 
repetitive replacement of the brushes in the A/C compressor motor 
assembly, or, as an option to the brush replacement, deactivation of 
the A/C system and placard installation; and return of replaced brushes 
to Cessna. We are issuing this AD to prevent the brushes in the A/C 
motor from wearing down beyond their limits, which could result in the 
rivet in the brush contacting the commutator, causing sparks and 
consequent fire and/or smoke in the tailcone with no means to detect or 
extinguish the fire and/or smoke.

Comments

    We gave the public the opportunity to participate in developing 
this AD. We received no comments on the NPRM (80 FR 3516, January 23, 
2015) or on the determination of the cost to the public.

Conclusion

    We reviewed the relevant data and determined that air safety and 
the public interest require adopting this AD as proposed except for 
minor editorial changes. We have determined that these minor changes:
    <bullet> Are consistent with the intent that was proposed in the 
NPRM (80 FR 3516, January 23, 2015) for correcting the unsafe 
condition; and
    <bullet> Do not add any additional burden upon the public than was 
already proposed in the NPRM (80 FR 3516, January 23, 2015).

Interim Action

    We consider this AD interim action. The reporting data required by 
this AD will enable us to obtain better insight into brush wear. The 
reporting data will also indicate if the replacement intervals we 
established are adequate. After we analyze the reporting data received, 
we might consider further rulemaking.

Related Service Information Under 1 CFR Part 51

    We reviewed the following service information, which describes 
procedures for replacement of life-limited components, including part 
number FWA1134104-1 or FWA1134104-5 A/C compressor motor brushes.
    <bullet> Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 6, dated June 23, 2014, of the 
Cessna Model 500/501 Maintenance Manual.
    <bullet> Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 10, dated June 23, 2014, of the 
Cessna Model 550/551 Maintenance Manual.
    <bullet> Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 12, dated June 23, 2014, of the 
Cessna Model 550 Bravo Maintenance Manual.
    <bullet> Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 9, dated June 23, 2014, of the 
Cessna Model S550 Maintenance Manual.
    <bullet> Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 22, dated June 23, 2014, of the 
Cessna Model 560 Maintenance Manual.
    <bullet> Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 32, dated June 23, 2014, of the 
Cessna Model 650 Maintenance Manual.
    This service information is reasonably available because the 
interested parties have access to it through their normal course of 
business or by the means identified in the ADDRESSES section of this 
AD.

Costs of Compliance

    We estimate that this AD affects 333 airplanes of U.S. registry.
    We estimate the following costs to comply with this AD:

[[Page 51445]]



                                       Estimated Costs--Brush Replacement
----------------------------------------------------------------------------------------------------------------
                                                                                                 Cost on U.S.
              Action                    Labor cost        Parts cost      Cost per product        operators
----------------------------------------------------------------------------------------------------------------
Inspection and replacement.......  11 work-hours x $85            $252  $1,187 per           $395,271 per
                                    per hour = $935                      replacement cycle.   replacement cycle.
                                    per replacement
                                    cycle.
Reporting/return parts...........  1 work-hour x $85                 0  85.................  $28,305 per return
                                    per hour = $85 per                                        (2 returns
                                    return.                                                   required).
----------------------------------------------------------------------------------------------------------------


                                        Estimated Costs--A/C Deactivation
----------------------------------------------------------------------------------------------------------------
                                                                                                     Cost per
                    Action                                 Labor cost               Parts cost        product
----------------------------------------------------------------------------------------------------------------
Fabrication of placard for A/C deactivation...  1 work-hour x $85 per hour = $85              $0             $85
Deactivation/reactivation of A/C..............  1 work-hour x $85 per hour = $85               0              85
----------------------------------------------------------------------------------------------------------------

Paperwork Reduction Act

    A federal agency may not conduct or sponsor, and a person is not 
required to respond to, nor shall a person be subject to penalty for 
failure to comply with a collection of information subject to the 
requirements of the Paperwork Reduction Act unless that collection of 
information displays a current valid OMB control number. The control 
number for the collection of information required by this AD is 2120-
0056. The paperwork cost associated with this AD has been detailed in 
the Costs of Compliance section of this document and includes time for 
reviewing instructions, as well as completing and reviewing the 
collection of information. Therefore, all reporting associated with 
this AD is mandatory. Comments concerning the accuracy of this burden 
and suggestions for reducing the burden should be directed to the FAA 
at 800 Independence Ave. SW., Washington, DC 20591. ATTN: Information 
Collection Clearance Officer, AES-200.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2015-17-12 Cessna Aircraft Company: Amendment 39-18245; Docket No. 
FAA-2014-1044; Directorate Identifier 2014-NM-148-AD.

(a) Effective Date

    This AD is effective September 29, 2015.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to the Cessna Aircraft Company airplanes, 
certificated in any category, identified in table 1 to paragraph (c) 
of this AD, that have an air conditioning (A/C) system installed via 
a Cessna Aircraft Company supplemental type certificate (STC) 
identified in paragraph (c)(1), (c)(2), (c)(3), or (c)(4) of this 
AD.
    (1) SA3849SW (<a href="http://rgl.faa.gov/Regulatory_and_Guidance_Library/rgstc.nsf/0/029C5719AD18E79C86257C1A0069742C?OpenDocument&Highlight=sa3849sw">http://rgl.faa.gov/Regulatory_and_Guidance_Library/rgstc.nsf/0/029C5719AD18E79C86257C1A0069742C?OpenDocument&Highlight=sa3849sw</a>).
    (2) SA7580SW (<a href="http://rgl.faa.gov/Regulatory_and_Guidance_Library/rgstc.nsf/0/7C9B0FB7D5923D4986257C1A0069E2C0?OpenDocument&Highlight=sa7580sw">http://rgl.faa.gov/Regulatory_and_Guidance_Library/rgstc.nsf/0/7C9B0FB7D5923D4986257C1A0069E2C0?OpenDocument&Highlight=sa7580sw</a>).
    (3) SA7753SW (<a href="http://rgl.faa.gov/Regulatory_and_Guidance_Library/rgstc.nsf/0/A78233CBB3314BAF86257C1A0069D128?OpenDocument&Highlight=sa7753sw">http://rgl.faa.gov/Regulatory_and_Guidance_Library/rgstc.nsf/0/A78233CBB3314BAF86257C1A0069D128?OpenDocument&Highlight=sa7753sw</a>).
    (4) SA8918SW (<a href="http://rgl.faa.gov/Regulatory_and_Guidance_Library/rgstc.nsf/0/5FAD7ABA3EAA464C86257C1A0069F239?OpenDocument&Highlight=sa8918sw">http://rgl.faa.gov/Regulatory_and_Guidance_Library/rgstc.nsf/0/5FAD7ABA3EAA464C86257C1A0069F239?OpenDocument&Highlight=sa8918sw</a>).

[[Page 51446]]



Table 1 to Paragraph (c) of this AD--Affected Airplane Models and Serial
                             Numbers (S/Ns)
------------------------------------------------------------------------
Cessna aircraft company airplane models                S/Ns
------------------------------------------------------------------------
Model 500 and 501 airplanes............  0001 through 0689 inclusive.
Model 550 and 551 airplanes............  0002 through 0733 inclusive,
                                          and 0801 through 1136
                                          inclusive.
Model S550 airplanes...................  0001 through 0160 inclusive.
Model 560 airplanes....................  0001 through 0707 inclusive,
                                          and 0751 through 0815
                                          inclusive.
Model 650 airplanes....................  0200 through 0241 inclusive,
                                          and 7001 through 7119
                                          inclusive.
------------------------------------------------------------------------

(d) Subject

    Air Transport Association (ATA) of America Code 21, Air 
Conditioning.

(e) Unsafe Condition

    This AD was prompted by reports of smoke and/or fire in the 
tailcone caused by sparking due to excessive wear of the brushes in 
the A/C motor. We are issuing this AD to prevent the brushes in the 
A/C motor from wearing down beyond their limits, which could result 
in the rivet in the brush contacting the commutator, causing sparks 
and consequent fire and/or smoke in the tailcone with no means to 
detect or extinguish the fire and/or smoke.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Inspection for Part Number (P/N)

    Within 30 days or 10 flight hours after the effective date of 
this AD, whichever occurs first: Inspect the A/C compressor motor to 
determine whether P/N FWA1134104-1 or P/N FWA1134104-5 is installed. 
A review of airplane maintenance records is acceptable in lieu of 
this inspection if the part number of the A/C compressor motor can 
be conclusively determined from that review.

(h) Inspection of Compressor Hour Meter and Maintenance Records

    If, during the inspection required by paragraph (g) of this AD, 
any A/C compressor motor having P/N FWA1134104-1 or P/N FWA1134104-5 
is found: Within 30 days or 10 flight hours after the effective date 
of this AD, whichever occurs first, determine the hour reading on 
the A/C compressor hour meter as specified in paragraphs (h)(1) and 
(h)(2) of this AD.
    (1) Inspect the number of hours accumulated on the A/C 
compressor hour meter.
    (2) Check the airplane logbook for any entry for replacing the 
A/C compressor motor brushes with new brushes, or for replacing the 
compressor motor or compressor condenser module assembly (pallet) 
with a motor or assembly that has new brushes.
    (i) If the logbook contains an entry for replacement of parts, 
as specified in paragraph (h)(2) of this AD, determine the number of 
hours accumulated on the A/C compressor motor brushes by comparing 
the number of hours on the compressor motor since replacement and 
use this number in lieu of the number determined in paragraph (h)(1) 
of this AD.
    (ii) If, through the logbook check, a determination cannot be 
made regarding the number of hours accumulated on the A/C compressor 
motor brushes, as specified in paragraph (h)(2) of this AD, use the 
number of hours accumulated on the A/C compressor hour meter 
determined in paragraph (h)(1) of this AD, or presume the brushes 
have over 500 hours time-in-service.

(i) Replacement

    Using the hour reading on the A/C compressor hour meter 
determined in paragraph (h) of this AD, replace the A/C compressor 
motor brushes with new brushes at the later of the times specified 
in paragraphs (i)(1) and (i)(2) of this AD. Thereafter, repeat the 
replacement of the A/C compressor motor brushes at intervals not to 
exceed 500 hours time-in-service on the A/C compressor motor. Do the 
replacement in accordance with the applicable Cessna maintenance 
manual subject specified in paragraphs (j)(1) through (j)(6) of this 
AD.
    (1) Before the accumulation of 500 total hours time-in-service 
on the A/C compressor motor.
    (2) Before further flight after doing the inspection required in 
paragraph (h) of this AD.

(j) Maintenance Manual Information for Replacement

    Use the instructions in the applicable Cessna maintenance manual 
subject specified in paragraphs (j)(1) through (j)(6) of this AD to 
do the replacement required by paragraph (i) of this AD.
    (1) Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 6, dated June 23, 2014, of the 
Cessna Model 500/501 Maintenance Manual.
    (2) Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 10, dated June 23, 2014, of the 
Cessna Model 550/551 Maintenance Manual.
    (3) Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 12, dated June 23, 2014, of the 
Cessna Model 550 Bravo Maintenance Manual.
    (4) Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 9, dated June 23, 2014, of the 
Cessna Model S550 Maintenance Manual.
    (5) Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 22, dated June 23, 2014, of the 
Cessna Model 560 Maintenance Manual.
    (6) Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 32, dated June 23, 2014, of the 
Cessna Model 650 Maintenance Manual.

(k) Deactivation of the A/C System

    In lieu of replacing the A/C compressor motor brushes as 
required by this AD, deactivate the A/C system as specified in 
paragraph (k)(1) or (k)(2) of this AD, as applicable.
    (1) For all airplanes except Model 650 airplanes: Pull the vapor 
cycle A/C circuit breaker labeled ``AIR COND,'' do the actions 
specified in paragraphs (k)(1)(i) and (k)(1)(ii) of this AD, and 
document deactivation of the system in the airplane logbook, 
referring to this AD as the reason for deactivation.
    (i) Fabricate a placard that states: ``A/C DISABLED'' with 1/8-
inch black lettering on a white background.
    (ii) Install the placard on the airplane instrument panel within 
6 inches of the A/C selection switch.
    (2) For Model 650 airplanes: Pull the vapor cycle A/C circuit 
breaker labeled ``FWD EVAP FAN,'' do the actions specified in 
paragraphs (k)(1)(i) and (k)(1)(ii) of this AD, and document 
deactivation of the system in the airplane logbook, referring to 
this AD as the reason for deactivation.

    Note 1 to paragraph (k) of this AD:  While the A/C system is 
deactivated, it is recommended that airplane operators remain aware 
of the operating temperature limitations specified in the applicable 
airplane flight manual.

(l) Reactivation of the A/C System

    If the A/C system is deactivated, as specified in paragraph (k) 
of this AD, prior to the A/C system being reactivated: Perform the 
inspection specified in paragraph (h) of this AD, and do the 
replacements specified in paragraph (i) of this AD, at the times 
specified in paragraph (i) of this AD. Return the A/C system to 
service by doing the actions specified in paragraph (l)(1) or (l)(2) 
of this AD, as applicable.
    (1) For all airplanes except Model 650 airplanes: Push in the 
vapor cycle A/C circuit breaker labeled ``AIR COND,'' remove the 
placard by the A/C selection switch that states ``A/C DISABLED,'' 
and document reactivation of the system in the airplane logbook.
    (2) For Model 650 airplanes: Push in the vapor cycle A/C circuit 
breaker labeled ``FWD EVAP FAN,'' remove the placard by the A/C 
selection switch that states ``A/C DISABLED,'' and document 
reactivation of the system in the airplane logbook.

(m) Parts Return and Reporting Requirements

    For the first two A/C compressor motor brush replacement cycles 
on each airplane, send the removed brushes to Cessna Aircraft 
Company, Cessna Service Parts and

[[Page 51447]]

Programs, 7121 Southwest Boulevard, Wichita, KS 67215. Provide the 
brushes and the information specified in paragraphs (m)(1) through 
(m)(6) of this AD within 30 days after the replacement if the 
replacement was done on or after the effective date of this AD, or 
within 30 days after the effective date of this AD if the 
replacement was done before the effective date of this AD.
    (1) The model and serial number of the airplane.
    (2) The part number of the motor.
    (3) The part number of the brushes, if known.
    (4) The elapsed time, in motor hours, since the last brush/motor 
replacement, if known.
    (5) If motor hours are unknown, report the elapsed airplane 
flight hours since the last brush/motor replacement, and indicate 
that motor hours are unknown.
    (6) The number of motor hours currently displayed on the pallet 
hour meter, if installed.

(n) Parts Installation Limitation

    As of the effective date of this AD, no person may install an A/
C compressor motor having P/N FWA1134104-1 or P/N FWA1134104-5, 
unless the inspection specified in paragraph (h) of this AD is done 
before installation, and the replacements specified in paragraph (i) 
of this AD are subsequently done in accordance with the applicable 
service information identified in paragraphs (j)(1) through (j)(6) 
of this AD at the times specified in paragraph (i) of this AD.

(o) Special Flight Permit Limitation

    Special flight permits may be issued in accordance with sections 
21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 
and 21.199) with the following limitation: Operation of the A/C 
system is prohibited.

(p) Paperwork Reduction Act Burden Statement

    A federal agency may not conduct or sponsor, and a person is not 
required to respond to, nor shall a person be subject to a penalty 
for failure to comply with a collection of information subject to 
the requirements of the Paperwork Reduction Act unless that 
collection of information displays a current valid OMB Control 
Number. The OMB Control Number for this information collection is 
2120-0056. Public reporting for this collection of information is 
estimated to be approximately 5 minutes per response, including the 
time for reviewing instructions, completing and reviewing the 
collection of information. All responses to this collection of 
information are mandatory. Comments concerning the accuracy of this 
burden and suggestions for reducing the burden should be directed to 
the FAA at: 800 Independence Ave. SW., Washington, DC 20591, Attn: 
Information Collection Clearance Officer, AES-200.

(q) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Wichita Aircraft Certification Office (ACO), 
FAA, has the authority to approve AMOCs for this AD, if requested 
using the procedures found in 14 CFR 39.19. In accordance with 14 
CFR 39.19, send your request to your principal inspector or local 
Flight Standards District Office, as appropriate. If sending 
information directly to the manager of the ACO, send it to the 
attention of the person identified in paragraph (r) of this AD.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.

(r) Related Information

    For more information about this AD, contact Craig Henrichsen, 
Aerospace Engineer, Electrical Systems and Avionics Branch, ACE-
119W, FAA, Wichita ACO, 1801 Airport Road, Room 100, Mid-Continent 
Airport, Wichita, KS 67209; phone: 316-946-4110; fax: 316-946-4107; 
email: <a href="/cdn-cgi/l/email-protection#571425363e30791f3239253e343f2432391731363679303821"><span class="__cf_email__" data-cfemail="2063524149470e68454e5249434853454e604641410e474f56">[email&#160;protected]</span></a>.

(s) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless the AD specifies otherwise.
    (i) Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 6, dated June 23, 2014, of the 
Cessna Model 500/501 Maintenance Manual.
    (ii) Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 10, dated June 23, 2014, of the 
Cessna Model 550/551 Maintenance Manual.
    (iii) Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 12, dated June 23, 2014, of the 
Cessna Model 550 Bravo Maintenance Manual.
    (iv) Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 9, dated June 23, 2014, of the 
Cessna Model S550 Maintenance Manual.
    (v) Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 22, dated June 23, 2014, of the 
Cessna Model 560 Maintenance Manual.
    (vi) Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 32, dated June 23, 2014, of the 
Cessna Model 650 Maintenance Manual.
    (3) For service information identified in this AD, contact 
Cessna Aircraft Co., P.O. Box 7706, Wichita, KS 67277; phone: 316-
517-6215; fax: 316-517-5802; email: <a href="/cdn-cgi/l/email-protection#b8dbd1ccd9ccd1d7d6c8cddacbf8dbddcbcbd6d996ccddc0cccad7d696dbd7d5"><span class="__cf_email__" data-cfemail="a6c5cfd2c7d2cfc9c8d6d3c4d5e6c5c3d5d5c8c788d2c3ded2d4c9c888c5c9cb">[email&#160;protected]</span></a>; 
Internet <a href="https://www.cessnasupport.com/newlogin.html">https://www.cessnasupport.com/newlogin.html</a>.
    (4) You may view this service information at FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For 
information on the availability of this material at the FAA, call 
425-227-1221.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: <a href="http://www.archives.gov/federal-register/cfr/ibr-locations.html">http://www.archives.gov/federal-register/cfr/ibr-locations.html</a>.

    Issued in Renton, Washington, on August 10, 2015.
Michael Kaszycki,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2015-20692 Filed 8-24-15; 8:45 am]
BILLING CODE 4910-13-P