AD 2015-17-05

[Federal Register Volume 80, Number 164 (Tuesday, August 25, 2015)]
[Rules and Regulations]
[Pages 51461-51463]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2015-20581]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2015-0676; Directorate Identifier 2014-NM-164-AD; 
Amendment 39-18238; AD 2015-17-05]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc. Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for certain 
Bombardier, Inc. Model BD-700-1A10 and BD-700-1A11 airplanes. This AD 
was prompted by a report of several events where pilots experienced 
difficulty in lateral control of the airplane after doing a climb 
through heavy rain conditions and a determination that the cause was 
water ingress in the aileron control pulley assembly. This AD requires, 
for certain airplanes, inspecting for correct clearance and rework if 
necessary, and, for certain other airplanes, installing a cover for the 
aileron pulley assembly. We are issuing this AD to prevent water 
ingress in the aileron control pulley assembly, which could freeze in 
cold conditions and result in reduced control of the airplane.

DATES: This AD becomes effective September 29, 2015.
    The Director of the Federal Register approved the incorporation by 
reference of certain publications listed in this AD as of September 29, 
2015.

ADDRESSES: You may examine the AD docket on the Internet at <a href="http://www.regulations.gov/#!docketDetail">http://www.regulations.gov/#!docketDetail</a>;D=FAA-2015-0676 or in person at the 
Docket Management Facility, U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC.
    For service information identified in this AD, contact Bombardier, 
Inc., 400 C[ocirc]te-Vertu Road West, Dorval, Qu[eacute]bec H4S 1Y9, 
Canada; telephone 514-855-5000; fax 514-855-7401; email 
<a href="/cdn-cgi/l/email-protection#bfcbd7db91dccdd5ffdedacdd091ddd0d2dddecddbd6dacd91dcd0d2"><span class="__cf_email__" data-cfemail="25514d410b46574f654440574a0b474a48474457414c40570b464a48">[email&#160;protected]</span></a>; Internet <a href="http://www.bombardier.com">http://www.bombardier.com</a>. You 
may view this referenced service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information 
on the availability of this material at the FAA, call 425-227-1221. It 
is also available on the Internet at <a href="http://www.regulations.gov">http://www.regulations.gov</a> by 
searching for and locating Docket No. FAA-2015-0676.

FOR FURTHER INFORMATION CONTACT: Fabio Buttitta, Aerospace Engineer, 
Airframe and Mechanical Systems Branch, ANE-171, FAA, New York Aircraft 
Certification Office (ACO), 1600 Stewart Avenue, Suite 410, Westbury, 
NY 11590; telephone 516-228-7303; fax 516-794-5531.

SUPPLEMENTARY INFORMATION: 

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 by adding an AD that would apply to certain Bombardier, Inc. 
Model BD-700-1A10 and BD-700-1A11 airplanes. The NPRM published in the 
Federal Register on March 30, 2015 (80 FR 16608).
    Transport Canada Civil Aviation (TCCA), which is the aviation 
authority for Canada, has issued Canadian Airworthiness Directive CF-
2014-23, dated July 18, 2014 (referred to after this as the Mandatory 
Continuing Airworthiness Information, or ``the MCAI''), to correct an 
unsafe condition for certain Bombardier, Inc. Model BD-700-1A10 and BD-
700-1A11 airplanes. The MCAI states:

    There have been several reports whereby pilots have experienced 
difficulty in lateral control following climb through heavy rain 
conditions. In each event, the pilots were able to overcome this 
difficulty without disconnecting the aileron control. An 
investigation has determined that the root cause of the restricted 
movement of the aileron was due to water ingress into the wing root 
aileron control pulley assembly through a gap on the wing-to-
fuselage fairing resulting in freezing of the aileron control 
system.

[[Page 51462]]

    If not corrected, this condition could result in reduced lateral 
control of the aeroplane.
    This [Canadian] AD mandates [for certain airplanes] the 
incorporation of a cover for the aileron pulley assembly [and 
inspection and rework if necessary] to prevent water ingress in the 
aileron control pulley assembly [and for certain other airplanes, 
mandates an inspection and rework if necessary].

    The inspection involves doing a general visual inspection for 
correct clearance. You may examine the MCAI in the AD docket on the 
Internet at <a href="http://www.regulations.gov/#!documentDetail">http://www.regulations.gov/#!documentDetail</a>;D=FAA-2015-
0676-0002.

Comments

    We gave the public the opportunity to participate in developing 
this AD. We received no comments on the NPRM (80 FR 16608, March 30, 
2015) or on the determination of the cost to the public.

Conclusion

    We reviewed the relevant data and determined that air safety and 
the public interest require adopting this AD as proposed except for 
minor editorial changes. We have determined that these minor changes:
    <bullet> Are consistent with the intent that was proposed in the 
NPRM (80 FR 16608, March 30, 2015) for correcting the unsafe condition; 
and
    <bullet> Do not add any additional burden upon the public than was 
already proposed in the NPRM (80 FR 16608, March 30, 2015).

Related Service Information Under 1 CFR Part 51

    Bombardier has issued the following service information:
    <bullet> Service Bulletin 700-1A11-27-034, Revision 04, dated 
September 4, 2014;
    <bullet> Service Bulletin 700-27-076, Revision 04, dated September 
4, 2014;
    <bullet> Service Bulletin 700-27-5004, Revision 04, dated September 
4, 2014; and
    <bullet> Service Bulletin 700-27-6004, Revision 04, dated September 
4, 2014.
    This service information describes procedures, for certain 
airplanes, for installing a cover for the No. 1 aileron pulley, 
including an inspection for correct clearance and rework, and for 
certain other airplanes, for an inspection for correct clearance and 
rework. This service information is reasonably available because the 
interested parties have access to it through their normal course of 
business or by the means identified in the ADDRESSES section of this 
AD.

Costs of Compliance

    We estimate that this AD affects 60 airplanes of U.S. registry.
    We also estimate that it will take about 9 work-hours per product 
to comply with the basic requirements of this AD. The average labor 
rate is $85 per work-hour. Based on these figures, we estimate the cost 
of this AD on U.S. operators to be $45,900, or $765 per product.
    According to the manufacturer, some of the costs of this AD may be 
covered under warranty, thereby reducing the cost impact on affected 
individuals. We do not control warranty coverage for affected 
individuals. As a result, we have included all costs in our cost 
estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

Examining the AD Docket

    You may examine the AD docket on the Internet at <a href="http://www.regulations.gov/#!docketDetail">http://www.regulations.gov/#!docketDetail</a>;D=FAA-2015-0676; or in person at the 
Docket Management Facility between 9 a.m. and 5 p.m., Monday through 
Friday, except Federal holidays. The AD docket contains this AD, the 
regulatory evaluation, any comments received, and other information. 
The street address for the Docket Operations office (telephone 800-647-
5527) is in the ADDRESSES section.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2015-17-05 Bombardier, Inc.: Amendment 39-18238. Docket No. FAA-
2015-0676; Directorate Identifier 2014-NM-164-AD.

(a) Effective Date

    This AD becomes effective September 29, 2015.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Bombardier, Inc. Model BD-700-1A10 and BD-
700-1A11 airplanes, certificated in any category, having serial 
numbers 9002 through 9520 inclusive and 9998.

(d) Subject

    Air Transport Association (ATA) of America Code 27, Flight 
Controls.

(e) Reason

    This AD was prompted by a report of several events where pilots 
experienced difficulty in lateral control of the airplane after 
doing a climb through heavy rain conditions and a determination that 
the cause was water ingress in the aileron control pulley assembly. 
We are issuing this AD to prevent water ingress in the aileron 
control pulley assembly, which could freeze in cold conditions and 
result in reduced control of the airplane.

[[Page 51463]]

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Installation of Cover for the Aileron Pulley Assembly

    Except as provided by paragraph (j) of this AD, for airplanes on 
which a cover for the No. 1 aileron pulley has not been installed as 
of the effective date of this AD: Within 150 flight cycles after the 
effective date of this AD, install a cover for the No. 1 aileron 
pulley, including doing a general visual inspection for correct 
clearance and rework as applicable, in accordance with paragraph C., 
``PART B--Modification,'' of the Accomplishment Instructions of the 
applicable service bulletins identified in paragraphs (g)(1) and 
(g)(2) for this AD.
    (1) For Model BD-700-1A10 airplanes: Bombardier Service Bulletin 
700-27-076, Revision 04, dated September 4, 2014; or 700-27-6004, 
Revision 04, dated September 4, 2014.
    (2) For Model BD-700-1A11 airplanes: Bombardier Service Bulletin 
700-1A11-27-034, Revision 04, dated September 4, 2014; or 700-27-
5004, Revision 04, dated September 4, 2014.

(h) Inspection and Rework

    Except as provided by paragraph (j) of this AD, for airplanes on 
which a cover for the No. 1 aileron pulley has been incorporated 
using the applicable service information identified in paragraphs 
(h)(1) and (h)(2) of this AD as of the effective date of this AD: 
Within 150 flight cycles after the effective date of this AD, do a 
general visual inspection for correct clearance and, before further 
flight, rework, as applicable, in accordance with paragraph B., 
``PART A--Inspection and Rework,'' of the Accomplishment 
Instructions of the applicable service information identified in 
paragraphs (g)(1) and (g)(2) of this AD.
    (1) For Model BD-700-1A10 airplanes: Bombardier Service Bulletin 
700-27-076, dated March 5, 2012; or 700-27-6004, dated March 5, 
2012.
    (2) For Model BD-700-1A11 airplanes: Bombardier Service Bulletin 
700-1A11-27-034, dated March 5, 2012; or 700-27-5004, dated March 5, 
2012.

(i) Re-Identification of Overwing Panels

    Except as provided by paragraph (j) of this AD, for airplanes on 
which the Service Non-Incorporated Engineering Orders (SNIEO) or 
Service Requests for Product Support Action (SRPSA) that are listed 
in table 2 of paragraph 1.A., ``Effectivity,'' in the applicable 
service information identified in paragraphs (i)(1), (i)(2), and 
(i)(3) of this AD have been incorporated: Within 150 flight cycles 
from the effective date of this AD, do the re-identification of the 
overwing panels, in accordance with paragraph 2.B(2)(g) of the 
Accomplishment Instructions of the applicable service information 
identified in paragraphs (g)(1) and (g)(2) of this AD.
    (1) Bombardier Service Bulletin 700-27-076, Revision 04, dated 
September 4, 2014.
    (2) Bombardier Service Bulletin 700-27-6004, Revision 04, dated 
September 4, 2014.
    (3) Bombardier Service Bulletin 700-1A11-27-034, Revision 04, 
dated September 4, 2014.

(j) Exception to the Requirements of Paragraphs (g), (h), and (i) of 
This AD

    Airplanes on which the applicable SRPSA, as identified in table 
1 of paragraph 1.A., ``Effectivity,'' in the applicable service 
information identified in paragraph (j)(1), (j)(2), or (j)(3) of 
this AD has been accomplished as of the effective date of this AD, 
meet the intent of paragraphs (g), (h), and (i) of this AD, and no 
further action is required.
    (1) Bombardier Service Bulletin 700-27-076, Revision 04, dated 
September 4, 2014.
    (2) Bombardier Service Bulletin 700-27-6004, Revision 04, dated 
September 4, 2014.
    (3) Bombardier Service Bulletin 700-1A11-27-034, Revision 04, 
dated September 4, 2014.

(k) Credit for Previous Actions

    This paragraph provides credit for actions required by 
paragraphs (g), (h), and (i) of this AD, if those actions were 
performed before the effective date of this AD using the applicable 
service information identified in paragraphs (k)(1) through (k)(8) 
of this AD, which are not incorporated by reference in this AD.
    (1) Bombardier Service Bulletin 700-1A11-27-034, Revision 01, 
dated July 16, 2012.
    (2) Bombardier Service Bulletin 700-1A11-27-034, Revision 02, 
dated June 17, 2014.
    (3) Bombardier Service Bulletin 700-27-076, Revision 01, dated 
July 16, 2012.
    (4) Bombardier Service Bulletin 700-27-076, Revision 02, dated 
June 17, 2014.
    (5) Bombardier Service Bulletin 700-27-5004, Revision 01, dated 
July 16, 2012.
    (6) Bombardier Service Bulletin 700-27-5004, Revision 02, dated 
June 17, 2014.
    (7) Bombardier Service Bulletin 700-27-6004, Revision 01, dated 
July 16, 2012.
    (8) Bombardier Service Bulletin 700-27-6004, Revision 02, dated 
June 17, 2014.

(l) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York Aircraft Certification Office (ACO), ANE-170, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the ACO, send it to ATTN: Program Manager, Continuing 
Operational Safety, FAA, New York ACO, 1600 Stewart Avenue, Suite 
410, Westbury, NY 11590; telephone 516-228-7300; fax 516-794-5531. 
Before using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
local flight standards district office/certificate holding district 
office. The AMOC approval letter must specifically reference this 
AD.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, New York ACO, 
ANE-170, FAA; or Transport Canada Civil Aviation (TCCA); or 
Bombardier, Inc.'s TCCA Design Approval Organization (DAO). If 
approved by the DAO, the approval must include the DAO-authorized 
signature.

 (m) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) Canadian Airworthiness Directive CF-2014-23, dated July 18, 
2014, for related information. This MCAI may be found in the AD 
docket on the Internet at <a href="http://www.regulations.gov/#!documentDetail">http://www.regulations.gov/#!documentDetail</a>;D=FAA-2015-0676-0002.
    (2) Service information identified in this AD that is not 
incorporated by reference is available at the addresses specified in 
paragraphs (n)(3) and (n)(4) of this AD.

(n) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) Bombardier Service Bulletin 700-1A11-27-034, Revision 04, 
dated September 4, 2014.
    (ii) Bombardier Service Bulletin 700-27-076, Revision 04, dated 
September 4, 2014.
    (iii) Bombardier Service Bulletin 700-27-5004, Revision 04, 
dated September 4, 2014.
    (iv) Bombardier Service Bulletin 700-27-6004, Revision 04, dated 
September 4, 2014.
    (3) For service information identified in this AD, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, 
Qu[eacute]bec H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-
7401; email <a href="/cdn-cgi/l/email-protection#44302c206a27362e042521362b6a262b29262536202d21366a272b29"><span class="__cf_email__" data-cfemail="b2c6dad69cd1c0d8f2d3d7c0dd9cd0dddfd0d3c0d6dbd7c09cd1dddf">[email&#160;protected]</span></a>; Internet <a href="http://www.bombardier.com">http://www.bombardier.com</a>.
    (4) You may view this service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For 
information on the availability of this material at the FAA, call 
425-227-1221.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: <a href="http://www.archives.gov/federal-register/cfr/ibr-locations.html">http://www.archives.gov/federal-register/cfr/ibr-locations.html</a>.

    Issued in Renton, Washington, on August 10, 2015.
Michael Kaszycki,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2015-20581 Filed 8-24-15; 8:45 am]
 BILLING CODE 4910-13-P