AD 2015-02-25

[Federal Register Volume 80, Number 27 (Tuesday, February 10, 2015)]
[Rules and Regulations]
[Pages 7285-7288]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2015-01663]



========================================================================
Rules and Regulations
                                                Federal Register
________________________________________________________________________

This section of the FEDERAL REGISTER contains regulatory documents 
having general applicability and legal effect, most of which are keyed 
to and codified in the Code of Federal Regulations, which is published 
under 50 titles pursuant to 44 U.S.C. 1510.

The Code of Federal Regulations is sold by the Superintendent of Documents. 
Prices of new books are listed in the first FEDERAL REGISTER issue of each 
week.

========================================================================


Federal Register / Vol. 80, No. 27 / Tuesday, February 10, 2015 / 
Rules and Regulations

[[Page 7285]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2014-0146; Directorate Identifier 2013-NM-243-AD; 
Amendment 39-18094; AD 2015-02-25]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc. Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for certain 
Bombardier, Inc. Model DHC-8-400 series airplanes. This AD was prompted 
by fuel system reviews conducted by the manufacturer. This AD requires 
replacing a fitting that is part of the refuel control solenoid valve 
assembly. We are issuing this AD to prevent the potential of ignition 
sources inside fuel tanks, which, in combination with flammable fuel 
vapors, could result in fuel tank explosions and consequent loss of the 
airplane.

DATES: This AD becomes effective March 17, 2015.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of March 17, 
2015.

ADDRESSES: You may examine the AD docket on the Internet at <a href="http://www.regulations.gov/#!docketDetail">http://www.regulations.gov/#!docketDetail</a>;D=FAA-2014-0146; or in person at the 
Docket Management Facility, U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC.
    For service information identified in this AD, contact Bombardier, 
Inc., Q-Series Technical Help Desk, 123 Garratt Boulevard, Toronto, 
Ontario M3K 1Y5, Canada; telephone 416-375-4000; fax 416-375-4539; 
email <a href="/cdn-cgi/l/email-protection#3c485458124d4f594e55594f7c5d594e53125e53515e5d4e5855594e125f5351"><span class="__cf_email__" data-cfemail="9eeaf6fab0efedfbecf7fbeddefffbecf1b0fcf1f3fcffecfaf7fbecb0fdf1f3">[email&#160;protected]</span></a>; Internet <a href="http://www.bombardier.com">http://www.bombardier.com</a>. You may view this referenced service information at 
the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, 
WA. For information on the availability of this material at the FAA, 
call 425-227-1221. It is also available on the Internet at <a href="http://www.regulations.gov">http://www.regulations.gov</a> by searching for and locating Docket No. FAA-2014-
0146.

FOR FURTHER INFORMATION CONTACT: Mazdak Hobbi, Aerospace Engineer, 
Propulsion and Services Branch, ANE-173, FAA, New York Aircraft 
Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, NY 
11590; telephone 516-228 7330; fax 516-794 5531.

SUPPLEMENTARY INFORMATION:

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 by adding an AD that would apply to certain Bombardier, Inc. 
Model DHC-8-400 series airplanes. The NPRM published in the Federal 
Register on March 28, 2014 (79 FR 17459). The NPRM was prompted by fuel 
system reviews conducted by the manufacturer. The NPRM proposed to 
require replacing a fitting that is part of the refuel control solenoid 
valve assembly. We are issuing this AD to prevent the potential of 
ignition sources inside fuel tanks, which, in combination with 
flammable fuel vapors, could result in fuel tank explosions and 
consequent loss of the airplane.
    Transport Canada Civil Aviation (TCCA), which is the aviation 
authority for Canada, has issued Canadian Airworthiness Directive CF-
2013-32, dated October 8, 2013 (referred to after this as the Mandatory 
Continuing Airworthiness Information, or ``the MCAI''), to correct an 
unsafe condition certain Bombardier, Inc. Model DHC-8-400 series 
airplanes. The MCAI states:

    During the incorporation of Modsum 4-126630, mandated by 
[Canadian] AD CF-2010-31 [<a href="http://wwwapps3.tc.gc.ca/Saf-Sec-Sur/2/cawis-swimn/images/doc-acrobat16x16.gif">http://wwwapps3.tc.gc.ca/Saf-Sec-Sur/2/cawis-swimn/images/doc-acrobat16x16.gif</a>; corresponding FAA AD 2011-
13-06, Amendment 39-16729 (76 FR 37258, June 27, 2011)], it has been 
reported that fitting part number (P/N) 82822074-951 has been 
installed through the rear spar instead of fitting P/N 82822074-005 
or 82822074-007. Fitting P/N 82822074-951 does not comply with the 
fuel tank safety standards introduced in Chapter 525 of the 
Airworthiness Manual through [a certain] Notice of Proposed 
Amendment (NPA) * * *. Therefore, this fitting shall be replaced to 
mitigate unsafe conditions that could result in a potential ignition 
source within the fuel system.
    This [Canadian] AD mandates the replacement of the above-
mentioned fittings with compliant fittings P/N 82822074-009.

You may examine the MCAI in the AD docket on the Internet at <a href="http://www.regulations.gov/#!documentDetail">http://www.regulations.gov/#!documentDetail</a>;D=FAA-2014-0146-0002.

Comments

    We gave the public the opportunity to participate in developing 
this AD. The following presents the comment received on the NPRM (79 FR 
17459, March 28, 2014) and the FAA's response to each comment.

Request To Mandate Only Certain Sections of the Service Information

    Horizon Air requested that we revise the NPRM (79 FR 17459, March 
28, 2014), to mandate only the section of the Accomplishment 
Instructions that corrects the unsafe condition (i.e., paragraph 3.B., 
``Procedure''). Horizon Air reasoned that paragraph (g) of the NPRM 
mandates the entire Accomplishment Instructions of Bombardier Service 
Bulletin 84-28-12, Revision A, dated June 20, 2013, and that the ``Job 
Set-Up'' and ``Close Out'' sections of the Accomplishment Instructions 
do not directly correct the unsafe condition. Horizon Air explained 
that requiring the ``Job Set-Up'' and ``Close Out'' sections restricts 
an operator's ability to perform other maintenance in conjunction with 
the incorporation of the service bulletin. As an example, Horizon Air 
suggested that an operator might need or want to have the gear pins 
out, but that would not be allowed because the NPRM mandates the 
installation of the gear pins through the work steps in the ``Job Set-
Up'' section, and they cannot be removed until the ``Job Close Out'' 
section is accomplished.
    For the reasons stated by Horizon Air, we agree to mandate only the 
section of the Accomplishment Instructions of Bombardier Service 
Bulletin 84-28-12,

[[Page 7286]]

Revision A, dated June 20, 2013, that corrects the unsafe condition in 
this AD. We have revised paragraph (g) of this AD accordingly.

``Contacting the Manufacturer'' Paragraph in This AD

    Since late 2006, we have included a standard paragraph titled 
``Airworthy Product'' in all MCAI ADs in which the FAA develops an AD 
based on a foreign authority's AD.
    The MCAI or referenced service information in an FAA AD often 
directs the owner/operator to contact the manufacturer for corrective 
actions, such as a repair. Briefly, the Airworthy Product paragraph 
allowed owners/operators to use corrective actions provided by the 
manufacturer if those actions were FAA-approved. In addition, the 
paragraph stated that any actions approved by the State of Design 
Authority (or its delegated agent) are considered to be FAA-approved.
    In the NPRM (79 FR 17459, March 28, 2014), we proposed to prevent 
the use of repairs that were not specifically developed to correct the 
unsafe condition, by requiring that the repair approval provided by the 
State of Design Authority or its delegated agent specifically refer to 
this FAA AD. This change was intended to clarify the method of 
compliance and to provide operators with better visibility of repairs 
that are specifically developed and approved to correct the unsafe 
condition. In addition, we proposed to change the phrase ``its 
delegated agent'' to include a design approval holder (DAH) with State 
of Design Authority design organization approval (DOA), as applicable, 
to refer to a DAH authorized to approve required repairs for the 
proposed AD.
    No comments were provided to the NPRM (79 FR 17459, March 28, 2014) 
about these proposed changes. However, a comment was provided for an 
NPRM having Directorate Identifier 2012-NM-101 AD (78 FR 78285, 
December 26, 2013). The commenter stated the following: ``The proposed 
wording, being specific to repairs, eliminates the interpretation that 
Airbus messages are acceptable for approving minor deviations 
(corrective actions) needed during accomplishment of an AD mandated 
Airbus service bulletin.''
    This comment has made the FAA aware that some operators have 
misunderstood or misinterpreted the Airworthy Product paragraph to 
allow the owner/operator to use messages provided by the manufacturer 
as approval of deviations during the accomplishment of an AD-mandated 
action. The Airworthy Product paragraph does not approve messages or 
other information provided by the manufacturer for deviations to the 
requirements of the AD-mandated actions. The Airworthy Product 
paragraph only addresses the requirement to contact the manufacturer 
for corrective actions for the identified unsafe condition and does not 
cover deviations from other AD requirements. However, deviations to AD-
required actions are addressed in 14 CFR 39.17, and anyone may request 
the approval for an alternative method of compliance to the AD-required 
actions using the procedures found in 14 CFR 39.19.
    To address this misunderstanding and misinterpretation of the 
Airworthy Product paragraph, we have changed the paragraph and retitled 
it ``Contacting the Manufacturer.'' This paragraph now clarifies that 
for any requirement in this AD to obtain corrective actions from a 
manufacturer, the actions must be accomplished using a method approved 
by the FAA, the TCCA, or Bombardier, Inc.'s TCCA Design Approval 
Organization (DAO).
    The Contacting the Manufacturer paragraph also clarifies that, if 
approved by the DAO, the approval must include the DAO-authorized 
signature. The DAO Designee signature indicates that the data and 
information contained in the document are TCCA-approved, which is also 
FAA-approved. Messages and other information provided by the 
manufacturer that do not contain the DAO-authorized signature approval 
are not TCCA-approved, unless TCCA directly approves the manufacturer's 
message or other information.
    This clarification does not remove flexibility previously afforded 
by the Airworthy Product paragraph. Consistent with long-standing FAA 
policy, such flexibility was never intended for required actions. This 
is also consistent with the recommendation of the Airworthiness 
Directive Implementation Aviation Rulemaking Committee to increase 
flexibility in complying with ADs by identifying those actions in 
manufacturers' service instructions that are ``Required for 
Compliance'' with ADs. We continue to work with manufacturers to 
implement this recommendation. But once we determine that an action is 
required, any deviation from the requirement must be approved as an 
alternative method of compliance.
    Other commenters to the NPRM having Directorate Identifier 2012-NM-
101 AD (78 FR 78285, December 26, 2013) pointed out that in many cases 
the foreign manufacturer's service bulletin and the foreign authority's 
MCAI might have been issued some time before the FAA AD. Therefore, the 
DOA might have provided U.S. operators with an approved repair, 
developed with full awareness of the unsafe condition, before the FAA 
AD is issued. Under these circumstances, to comply with the FAA AD, the 
operator would be required to go back to the manufacturer's DOA and 
obtain a new approval document, adding time and expense to the 
compliance process with no safety benefit.
    Based on these comments, we removed the requirement that the DAH-
provided repair specifically refer to this AD. Before adopting such a 
requirement, the FAA will coordinate with affected DAHs and verify they 
are prepared to implement means to ensure that their repair approvals 
consider the unsafe condition addressed in this AD. Any such 
requirements will be adopted through the normal AD rulemaking process, 
including notice-and-comment procedures, when appropriate.
    We also have decided not to include a generic reference to either 
the ``delegated agent'' or ``DAH with State of Design Authority design 
organization approval,'' but instead we have provided the specific 
delegation approval granted by the State of Design Authority for the 
DAH.

Conclusion

    We reviewed the relevant data, considered the comments received, 
and determined that air safety and the public interest require adopting 
this AD with the changes described previously and minor editorial 
changes. We have determined that these minor changes:
    <bullet> Are consistent with the intent that was proposed in the 
NPRM (79 FR 17459, March 28, 2014) for correcting the unsafe condition; 
and
    <bullet> Do not add any additional burden upon the public than was 
already proposed in the NPRM (79 FR 17459, March 28, 2014).
    We also determined that these changes will not increase the 
economic burden on any operator or increase the scope of this AD.

Related Service Information Under 1 CFR Part 51

    Bombardier has issued Bombardier Service Bulletin 84-28-12, 
Revision A, dated June 20, 2013. The service information describes 
procedures for replacing a fitting that is part of the refuel control 
solenoid valve assembly. This service information is reasonably 
available; see ADDRESSES for ways to access this service information.

[[Page 7287]]

Costs of Compliance

    We estimate that this AD affects 55 airplanes of U.S. registry.
    We also estimate that it will take about 9 work-hours per product 
to comply with the basic requirements of this AD. The average labor 
rate is $85 per work-hour. Required parts costs are negligible. Based 
on these figures, we estimate the cost of this AD on U.S. operators to 
be $42,075, or $765 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

Examining the AD Docket

    You may examine the AD docket on the Internet at <a href="http://www.regulations.gov/#!docketDetail">http://www.regulations.gov/#!docketDetail</a>;D=FAA-2014-0146; or in person at the 
Docket Management Facility between 9 a.m. and 5 p.m., Monday through 
Friday, except Federal holidays. The AD docket contains this AD, the 
regulatory evaluation, any comments received, and other information. 
The street address for the Docket Operations office (telephone 800-647-
5527) is in the ADDRESSES section.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2015-02-25 Bombardier, Inc.: Amendment 39-18094. Docket No. FAA-
2014-0146; Directorate Identifier 2013-NM-243-AD.

(a) Effective Date

    This AD becomes effective March 17, 2015.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Bombardier, Inc. Model DHC-8-400, -401, and -
402 airplanes, certificated in any category, serial numbers 4063 
through 4118 inclusive.

(d) Subject

    Air Transport Association (ATA) of America Code 28, Fuel.

(e) Reason

    This AD was prompted by fuel system reviews conducted by the 
manufacturer. We are issuing this AD to prevent the potential of 
ignition sources inside fuel tanks, which, in combination with 
flammable fuel vapors, could result in fuel tank explosions and 
consequent loss of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Replacement

    Within 6,000 flight hours or 36 months after the effective date 
of this AD, whichever occurs first: Replace fitting part number (P/
N) 82822074-951 with new P/N 82822074-009, in accordance with 
paragraph 3.B., ``Procedure,'' of the Accomplishment Instructions of 
Bombardier Service Bulletin 84-28-12, Revision A, dated June 20, 
2013.

(h) Credit for Previous Actions

    This paragraph provides credit for actions required by paragraph 
(g) of this AD, if those actions were performed before the effective 
date of this AD using Bombardier Service Bulletin 84-28-12, dated 
July 23, 2012, which is not incorporated by reference in this AD.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York Aircraft Certification Office (ACO), ANE-170, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the ACO, send it to ATTN: Program Manager, Continuing 
Operational Safety, FAA, New York ACO, 1600 Stewart Avenue, Suite 
410, Westbury, NY 11590; telephone 516-228-7300; fax 516-794-5531. 
Before using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
local flight standards district office/certificate holding district 
office. The AMOC approval letter must specifically reference this 
AD.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, New York ACO, 
ANE-170, FAA; or Transport Canada Civil Aviation (TCCA); or 
Bombardier, Inc.'s TCCA Design Approval Organization (DAO). If 
approved by the DAO, the approval must include the DAO-authorized 
signature.

(j) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) Canadian Airworthiness Directive CF-2013-32, dated October 8, 
2013, for related information. This MCAI may be found in the AD 
docket on the Internet at <a href="http://www.regulations.gov/#!documentDetail">http://www.regulations.gov/#!documentDetail</a>;D=FAA-2014-00146-0002.
    (2) Service information identified in this AD that is not 
incorporated by reference is available at the addresses specified in 
paragraphs (k)(3) and (k)(4) of this AD.

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) Bombardier Service Bulletin 84-28-12, Revision A, dated June 
20, 2013.
    (ii) Reserved.
    (3) For service information identified in this AD, contact 
Bombardier, Inc., Q-Series Technical Help Desk, 123 Garratt 
Boulevard, Toronto, Ontario M3K 1Y5, Canada; telephone 416-375-4000; 
fax 416-375-4539;

[[Page 7288]]

email <a href="/cdn-cgi/l/email-protection#f88c909cd6898b9d8a919d8bb8999d8a97d69a97959a998a9c919d8ad69b9795"><span class="__cf_email__" data-cfemail="83f7ebe7adf2f0e6f1eae6f0c3e2e6f1ecade1eceee1e2f1e7eae6f1ade0ecee">[email&#160;protected]</span></a>; Internet <a href="http://www.bombardier.com">http://www.bombardier.com</a>.
    (4) You may view this service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For 
information on the availability of this material at the FAA, call 
425-227-1221.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: <a href="http://www.archives.gov/federal-register/cfr/ibr-locations.html">http://www.archives.gov/federal-register/cfr/ibr-locations.html</a>.

    Issued in Renton, Washington, on January 21, 2015.
Jeffrey E. Duven,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2015-01663 Filed 2-9-15; 8:45 am]
BILLING CODE 4910-13-P