AD 2014-21-07

[Federal Register Volume 79, Number 208 (Tuesday, October 28, 2014)]
[Rules and Regulations]
[Pages 64086-64088]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2014-25022]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2014-0287; Directorate Identifier 2013-NM-247-AD; 
Amendment 39-18000; AD 2014-21-07]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc. Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for certain 
Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 701, & 
702) airplanes, Model CL-600-2D24 (Regional Jet Series 900) airplanes, 
and Model CL-600-2E25 (Regional Jet Series 1000) airplanes. This AD was 
prompted by a report that certain parts of the aft baggage door did not 
conform to the design specifications and were of degraded strength. 
This AD requires repetitive inspections for cracking and deformations 
of certain stop fittings and striker plates of the aft baggage bay 
door; and replacement, which would terminate the repetitive 
inspections. We are issuing this AD to prevent cracking and 
deformations of certain stop fittings and striker plates, which could 
result in the opening of the aft baggage bay door and rapid 
decompression or reduced controllability of the airplane.

DATES: This AD becomes effective December 2, 2014.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of December 2, 
2014.

ADDRESSES: You may examine the AD docket on the Internet at <a href="http://www.regulations.gov/#!docketDetail">http://www.regulations.gov/#!docketDetail</a>;D=FAA-2014-0287; or in person at the 
Docket Management Facility, U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC.
    For service information identified in this AD, contact Bombardier, 
Inc., 400 C[ocirc]te-Vertu Road West, Dorval, Qu[eacute]bec H4S 1Y9, 
Canada; telephone 514-855-5000; fax 514-855-7401; email 
<a href="/cdn-cgi/l/email-protection#37435f531954455d77565245581955585a555645535e52451954585a"><span class="__cf_email__" data-cfemail="88fce0eca6ebfae2c8e9edfae7a6eae7e5eae9faece1edfaa6ebe7e5">[email&#160;protected]</span></a>; Internet <a href="http://www.bombardier.com">http://www.bombardier.com</a>. You 
may view this referenced service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information 
on the availability of this material at the FAA, call 425-227-1221.

FOR FURTHER INFORMATION CONTACT: Ricardo Garcia, Aerospace Engineer, 
Airframe and Mechanical Systems Branch, ANE-171, FAA, New York Aircraft 
Certification Office (ACO), 1600 Stewart Avenue, Suite 410, Westbury, 
NY 11590; telephone 516-228-7331; fax 516-794-5531.

SUPPLEMENTARY INFORMATION:

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 by adding an AD that would apply to certain Bombardier, Inc. 
Model CL-600-2C10 (Regional Jet Series 700, 701, & 702) airplanes, 
Model CL-600-2D24 (Regional Jet Series 900) airplanes, and Model CL-
600-2E25 (Regional Jet Series 1000) airplanes. The NPRM published in 
the Federal Register on May 29, 2014 (79 FR 30751).
    Transport Canada Civil Aviation (TCCA), which is the aviation 
authority for Canada, has issued Canadian Airworthiness Directive CF-
2013-37, dated November 28, 2013 (referred to after this as the 
Mandatory Continuing Airworthiness Information, or ``the MCAI''), to 
correct an unsafe condition on certain Bombardier, Inc. Model CL-600-
2C10 (Regional Jet Series 700, 701, & 702) airplanes, Model CL-600-2D24 
(Regional Jet Series 900) airplanes, and Model CL-600-2E25 (Regional 
Jet Series 1000) airplanes. The MCAI states:

    During the manufacturing process, it was found that certain aft 
baggage bay door stop fittings and striker plates did not conform to 
the design specifications due to a quality control problem. This 
quality escape could degrade the strength of the affected aft 
baggage bay door stop fittings and striker plates. Failure of the 
aft baggage bay door stop fittings or striker plates may result in 
the opening of the aft baggage bay door and consequent rapid 
decompression of the aeroplane during flight.
    This [Canadian] AD mandates the initial and repetitive 
inspections of each aft baggage bay door stop fitting and striker 
plate until the terminating action [stop fitting/striker plate 
replacement] is accomplished.

    You may examine the MCAI in the AD docket on the Internet at <a href="http://www.regulations.gov/#!documentDetail">http://www.regulations.gov/#!documentDetail</a>;D=FAA-2014-0287-0002.

Comments

    We gave the public the opportunity to participate in developing 
this AD. We received no comments on the NPRM (79 FR 30751, May 29, 
2014) or on the determination of the cost to the public.

[[Page 64087]]

``Contacting the Manufacturer'' Paragraph in This AD

    Since late 2006, we have included a standard paragraph titled 
``Airworthy Product'' in all MCAI ADs in which the FAA develops an AD 
based on a foreign authority's AD.
    We have become aware that some operators have misunderstood or 
misinterpreted the Airworthy Product paragraph to allow the owner/
operator to use messages provided by the manufacturer as approval of 
deviations during the accomplishment of an AD-mandated action. The 
Airworthy Product paragraph does not approve messages or other 
information provided by the manufacturer for deviations to the 
requirements of the AD-mandated actions. The Airworthy Product 
paragraph only addresses the requirement to contact the manufacturer 
for corrective actions for the identified unsafe condition and does not 
cover deviations from other AD requirements. However, deviations to AD-
required actions are addressed in 14 CFR 39.17, and anyone may request 
the approval for an alternative method of compliance to the AD-required 
actions using the procedures found in 14 CFR 39.19.
    To address this misunderstanding and misinterpretation of the 
Airworthy Product paragraph, we have changed the paragraph and retitled 
it ``Contacting the Manufacturer.'' This paragraph now clarifies that 
for any requirement in this AD to obtain corrective actions from a 
manufacturer, the actions must be accomplished using a method approved 
by the FAA, TCCA, or Bombardier, Inc.'s TCCA Design Approval 
Organization (DAO).
    The Contacting the Manufacturer paragraph also clarifies that, if 
approved by the DAO, the approval must include the DAO-authorized 
signature. The DAO signature indicates that the data and information 
contained in the document are TCCA-approved, which is also FAA-
approved. Messages and other information provided by the manufacturer 
that do not contain the DAO-authorized signature approval are not TCCA-
approved, unless TCCA directly approves the manufacturer's message or 
other information.
    This clarification does not remove flexibility previously afforded 
by the Airworthy Product paragraph. Consistent with long-standing FAA 
policy, such flexibility was never intended for required actions. This 
is also consistent with the recommendation of the Airworthiness 
Directive Implementation Aviation Rulemaking Committee to increase 
flexibility in complying with ADs by identifying those actions in 
manufacturers' service instructions that are ``Required for 
Compliance'' with ADs. We continue to work with manufacturers to 
implement this recommendation. But once we determine that an action is 
required, any deviation from the requirement must be approved as an 
alternative method of compliance.
    We also have decided not to include a generic reference to either 
the ``delegated agent'' or ``design approval holder (DAH) with State of 
Design Authority design organization approval,'' but instead we have 
provided the specific delegation approval granted by the State of 
Design Authority for the DAH.

Conclusion

    We reviewed the relevant data and determined that air safety and 
the public interest require adopting this AD with the changes described 
previously and minor editorial changes. We have determined that these 
minor changes:
    <bullet> Are consistent with the intent that was proposed in the 
NPRM (79 FR 30751, May 29, 2014) for correcting the unsafe condition; 
and
    <bullet> Do not add any additional burden upon the public than was 
already proposed in the NPRM (79 FR 30751, May 29, 2014).
    We also determined that these changes will not increase the 
economic burden on any operator or increase the scope of this AD.

Costs of Compliance

    We estimate that this AD affects 73 airplanes of U.S. registry.
    We also estimate that it will take about 1 work-hour per product to 
comply with the basic requirements of this AD. The average labor rate 
is $85 per work-hour. Required parts will cost $0 per product. Based on 
these figures, we estimate the cost of this AD on U.S. operators to be 
$6,205, or $85 per product.
    In addition, we estimate that any necessary follow-on actions will 
take about 22 work-hours and require parts costing $0, for a cost of 
$1,870 per product. We have no way of determining the number of 
aircraft that might need this action.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

Examining the AD Docket

    You may examine the AD docket on the Internet at <a href="http://www.regulations.gov/#!docketDetail">http://www.regulations.gov/#!docketDetail</a>;D=FAA-2014-0287; or in person at the 
Docket Management Facility between 9 a.m. and 5 p.m., Monday through 
Friday, except Federal holidays. The AD docket contains this AD, the 
regulatory evaluation, any comments received, and other information. 
The street address for the Docket Operations office (telephone 800-647-
5527) is in the ADDRESSES section.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

[[Page 64088]]

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2014-21-07 Bombardier, Inc.: Amendment 39-18000. Docket No. FAA-
2014-0287; Directorate Identifier 2013-NM-247-AD.

(a) Effective Date

    This AD becomes effective December 2, 2014.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to the Bombardier, Inc. airplanes specified in 
paragraphs (c)(1), (c)(2), and (c)(3) of this AD, certificated in 
any category.
    (1) Model CL-600-2C10 (Regional Jet Series 700, 701, & 702) 
airplanes, serial numbers 10303 through 10333 inclusive.
    (2) Model CL-600-2D24 (Regional Jet Series 900) airplanes, 
serial numbers 15257 through 15284 inclusive.
    (3) Model CL-600-2E25 (Regional Jet Series 1000) airplanes, 
serial numbers 19011 through 19024 inclusive.

(d) Subject

    Air Transport Association (ATA) of America Code 52, Doors.

(e) Reason

    This AD was prompted by a report that certain parts of the aft 
baggage door did not conform to the design specifications and were 
of degraded strength. We are issuing this AD to prevent cracking and 
deformations of stop fittings and striker plates, which could result 
in the opening of the aft baggage bay door and rapid decompression 
or reduced controllability of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Inspections of the Aft Baggage Bay Door Stop Fittings and Striker 
Plates

    Within 600 flight hours or 6 months after the effective date of 
this AD, whichever occurs first: Do a detailed visual inspection for 
cracking and deformations of the stop fittings and striker plates of 
the aft baggage bay door, in accordance with the Accomplishment 
Instructions of Bombardier Service Bulletin 670BA-52-037, Revision 
B, dated September 16, 2013. Repeat the inspection thereafter at 
intervals not to exceed 2,000 flight hours or 12 months, whichever 
occurs first, until the terminating action specified in paragraph 
(h) of this AD has been accomplished. If a crack or deformation is 
found on a stop fitting or striker plate, before further flight, 
replace the affected fittings and striker plates, in accordance with 
the Accomplishment Instructions of Bombardier Service Bulletin 
670BA-52-037, Revision B, dated September 16, 2013.

(h) Terminating Action--Replacement of the Aft Baggage Bay Door Stop 
Fittings and Striker Plates

    Within 6,000 flight hours or 36 months, whichever occurs first, 
after the effective date of this AD: Replace the affected stop 
fittings and striker plates, in accordance with the Accomplishment 
Instructions of Bombardier Service Bulletin 670BA-52-037, Revision 
B, dated September 16, 2013. Replacement of the affected stop 
fittings and striker plates of the aft baggage bay door constitutes 
terminating action for the repetitive inspections required by 
paragraph (g) of this AD.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York Aircraft Certification Office (ACO), ANE-170, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the ACO, send it to ATTN: Program Manager, Continuing 
Operational Safety, FAA, New York ACO, 1600 Stewart Avenue, Suite 
410, Westbury, NY 11590; telephone 516-228-7300; fax 516-794-5531. 
Before using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
local flight standards district office/certificate holding district 
office. The AMOC approval letter must specifically reference this 
AD.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, New York ACO, 
ANE-170, Engine and Propeller Directorate, FAA; or Transport Canada 
Civil Aviation (TCCA); or Bombardier, Inc.'s TCCA Design Approval 
Organization (DAO). If approved by the DAO, the approval must 
include the DAO-authorized signature.

(j) Related Information

    Refer to Mandatory Continuing Airworthiness Information (MCAI) 
Canadian Airworthiness Directive CF-2013-37, dated November 28, 
2013, for related information. This MCAI may be found in the AD 
docket on the Internet at <a href="http://www.regulations.gov/#!documentDetail">http://www.regulations.gov/#!documentDetail</a>;D=FAA-2014-0287-0002.

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) Bombardier Service Bulletin 670BA-52-037, Revision B, dated 
September 16, 2013.
    (ii) Reserved.
    (3) For service information identified in this AD, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, 
Qu[eacute]bec H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-
7401; email <a href="/cdn-cgi/l/email-protection#e99d818dc78a9b83a9888c9b86c78b86848b889b8d808c9bc78a8684"><span class="__cf_email__" data-cfemail="196d717d377a6b7359787c6b76377b76747b786b7d707c6b377a7674">[email&#160;protected]</span></a>; Internet <a href="http://www.bombardier.com">http://www.bombardier.com</a>.
    (4) You may view this service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For 
information on the availability of this material at the FAA, call 
425-227-1221.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: <a href="http://www.archives.gov/federal-register/cfr/ibr-locations.html">http://www.archives.gov/federal-register/cfr/ibr-locations.html</a>.

    Issued in Renton, Washington, on October 13, 2014.
Michael Kaszycki,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2014-25022 Filed 10-27-14; 8:45 am]
BILLING CODE 4910-13-P