AD 2014-16-26

[Federal Register Volume 79, Number 166 (Wednesday, August 27, 2014)]
[Rules and Regulations]
[Pages 51077-51080]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2014-19678]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2014-0258; Directorate Identifier 2013-NM-065-AD; 
Amendment 39-17950; AD 2014-16-26]
RIN 2120-AA64


Airworthiness Directives; Dassault Aviation Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for certain 
Dassault Aviation Model FALCON 900EX airplanes. This AD was prompted by 
our determination to introduce a corrosion prevention control program, 
among other changes, to the maintenance requirements and airworthiness 
limitations. This AD requires revising the maintenance or inspection 
program, as applicable, to include the maintenance tasks and 
airworthiness limitations specified in the Airworthiness Limitations 
section of the airplane maintenance manual. We are issuing this AD to 
prevent reduced structural integrity and reduced controllability of the 
airplane.

DATES: This AD becomes effective October 1, 2014.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of October 1, 
2014.

ADDRESSES: You may examine the AD docket on the Internet at <a href="http://www.regulations.gov/#!docketDetail">http://www.regulations.gov/#!docketDetail</a>;D=FAA-2014-0258 or in person at the 
Docket Management Facility, U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC.
    For service information identified in this AD, contact Dassault 
Falcon Jet, P.O. Box 2000, South Hackensack, NJ 07606; telephone 201-
440-6700; Internet <a href="http://www.dassaultfalcon.com">http://www.dassaultfalcon.com</a>. You may view this 
referenced service information at the FAA, Transport Airplane 
Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the 
availability of this material at the FAA, call 425-227-1221.

FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue SW., Renton, WA 98057-3356; telephone 425-227-1137; 
fax 425-227-1149.

SUPPLEMENTARY INFORMATION:

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 by adding an AD that would apply to certain Dassault Aviation 
Model FALCON 900EX airplanes. The NPRM published in the Federal 
Register on May 2, 2014 (79 FR 25033). The NPRM was prompted by our 
determination to introduce a corrosion prevention control program, 
among other changes, to the maintenance requirements and airworthiness 
limitations. The NPRM proposed to require revising the maintenance or 
inspection program, as applicable, to include the maintenance tasks and 
airworthiness limitations specified in the Airworthiness Limitations 
section of the airplane maintenance manual. We are issuing this AD to 
prevent reduced structural integrity and reduced controllability of the 
airplane.
    The European Aviation Safety Agency (EASA), which is the Technical 
Agent for the Member States of the European Community, has issued EASA 
Airworthiness Directive 2013-0051, dated March 4, 2013 (referred to 
after this as the Mandatory Continuing Airworthiness Information, or 
``the MCAI''), to correct an unsafe condition for Dassault Aviation 
Model FALCON 900EX airplanes. The MCAI states:

    The airworthiness limitations and maintenance requirements for 
the Falcon 900EX type design are included in Dassault Aviation 
Aircraft Maintenance Manual (AMM) chapter 5-40 and are approved by 
the European Aviation Safety Agency (EASA).
    EASA issued AD 2008-0221 [<a href="http://ad.easa.europa.eu/blob/easa_ad_2008_0221_Corrected.pdf/AD_2008_0221_1">http://ad.easa.europa.eu/blob/easa_ad_2008_0221_Corrected.pdf/AD_2008_0221_1</a>] to require accomplishment of 
the maintenance

[[Page 51078]]

tasks, and implementation of the airworthiness limitations, as 
specified in Dassault Aviation F900EX AMM chapter 5-40 referenced 
DGT 113874 at revision 8.
    Since that [EASA] AD was issued, Dassault Aviation issued 
revision 12 of F900EX AMM chapter 5-40 which contains new or more 
restrictive maintenance requirements and/or airworthiness 
limitations and introduces, among others, the following changes:

--Tasks renumbering,
--Introduction of a Corrosion Prevention Control Program (CPCP),
--Upgrade of screwjack of flap actuators from the older to the 
latest -3 version;
--Revised Time Between Overhaul for screwjack of flap actuators -3 
version;
--Revised interval for checking the screw/nut play on screwjack of 
flap actuators -3 version;
--Removal of service life limit for screwjack of flap actuators;
--Test of flap asymmetry protection system. Compliance with this 
test is required by [a certain French AD ***, which corresponds to 
FAA AD 2002-23-20, Amendment 39-12964 (67 FR 71098, November 29, 
2002)], but F900EX AMM chapter 5-40 at revision 12 introduces an 
extended inspection interval;
--Inspection procedures of fuselage and wings;
--Check of overpressure tightness on pressurization control 
regulating valves. Compliance with this check is required by EASA AD 
2008-0072 [<a href="http://ad.easa.europa.eu/blob/easa_ad_2008_0072.pdf/AD_2008-0072_1">http://ad.easa.europa.eu/blob/easa_ad_2008_0072.pdf/AD_2008-0072_1</a>, which corresponds to FAA AD 2010-26-05, Amendment 
39-16544 (75 FR 79952, December 21, 2010)], but F900EX AMM chapter 
5-40 at revision 12 introduces an extended inspection interval;
--Check of overpressure relief valve vacuum supply lines.
    The maintenance tasks and airworthiness limitations, as 
specified in the F900EX AMM chapter 5-40, have been identified as 
mandatory actions for continued airworthiness of the F900EX type 
design. Failure to comply with AMM chapter 5-40 at revision 12 may 
result in an unsafe condition [e.g., reduced structural integrity 
and reduced controllability of the airplane].

    For the reasons described above, this [EASA] AD requires the 
implementation of the maintenance tasks and airworthiness 
limitations, as specified in the Dassault Aviation F900EX AMM 
chapter 5-40 DGT 113874 at revision 12.

You may examine the MCAI in the AD docket on the Internet at <a href="http://www.regulations.gov/#!documentDetail">http://www.regulations.gov/#!documentDetail</a>;D=FAA-2014-0258-0002.

Comments

    We gave the public the opportunity to participate in developing 
this AD. We received no comments on the NPRM (79 FR 25033, May 2, 2014) 
or on the determination of the cost to the public.

``Contacting the Manufacturer'' Paragraph in This AD

    Since late 2006, we have included a standard paragraph titled 
``Airworthy Product'' in all MCAI ADs in which the FAA develops an AD 
based on a foreign authority's AD.
    We have become aware that some operators have misunderstood or 
misinterpreted the Airworthy Product paragraph to allow the owner/
operator to use messages provided by the manufacturer as approval of 
deviations during the accomplishment of an AD-mandated action. The 
Airworthy Product paragraph does not approve messages or other 
information provided by the manufacturer for deviations to the 
requirements of the AD-mandated actions. The Airworthy Product 
paragraph only addresses the requirement to contact the manufacturer 
for corrective actions for the identified unsafe condition and does not 
cover deviations from other AD requirements. However, deviations to AD-
required actions are addressed in 14 CFR 39.17, and anyone may request 
the approval for an alternative method of compliance to the AD-required 
actions using the procedures found in 14 CFR 39.19.
    To address this misunderstanding and misinterpretation of the 
Airworthy Product paragraph, we have changed the paragraph and retitled 
it ``Contacting the Manufacturer.'' This paragraph now clarifies that 
for any requirement in this AD to obtain corrective actions from a 
manufacturer, the actions must be accomplished using a method approved 
by the FAA, the European Aviation Safety Agency (EASA), or Dassault 
Aviation's EASA Design Organization Approval (DOA).
    The Contacting the Manufacturer paragraph also clarifies that, if 
approved by the DOA, the approval must include the DOA-authorized 
signature. The DOA signature indicates that the data and information 
contained in the document are EASA-approved, which is also FAA-
approved. Messages and other information provided by the manufacturer 
that do not contain DOA-authorized signature approval are not EASA-
approved, unless EASA directly approves the manufacturer's message or 
other information.
    This clarification does not remove flexibility previously afforded 
by the Airworthy Product paragraph. Consistent with long-standing FAA 
policy, such flexibility was never intended for required actions. This 
is also consistent with the recommendation of the Airworthiness 
Directive Implementation Aviation Rulemaking Committee to increase 
flexibility in complying with ADs by identifying those actions in 
manufacturers' service instructions that are ``Required for 
Compliance'' with ADs. We continue to work with manufacturers to 
implement this recommendation. But once we determine that an action is 
required, any deviation from the requirement must be approved as an 
alternative method of compliance.

Conclusion

    We reviewed the relevant data and determined that air safety and 
the public interest require adopting this AD with the changes described 
previously and minor editorial changes. We have determined that these 
minor changes:
    <bullet> Are consistent with the intent that was proposed in the 
NPRM (79 FR 25033, May 2, 2014) for correcting the unsafe condition; 
and
    <bullet> Do not add any additional burden upon the public than was 
already proposed in the NPRM (79 FR 25033, May 2, 2014).
    We also determined that these changes will not increase the 
economic burden on any operator or increase the scope of this AD.

Costs of Compliance

    We estimate that this AD affects 72 airplanes of U.S. registry.
    We also estimate that it will take about 1 work-hour per product to 
comply with the basic requirements of this AD. The average labor rate 
is $85 per work-hour. Required parts will cost about $0 per product. 
Based on these figures, we estimate the cost of this AD on U.S. 
operators to be $6,120, or $85 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

[[Page 51079]]

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

Examining the AD Docket

    You may examine the AD docket on the Internet at <a href="http://www.regulations.gov/#!docketDetail">http://www.regulations.gov/#!docketDetail</a>;D=FAA-2014-0258; or in person at the 
Docket Management Facility between 9 a.m. and 5 p.m., Monday through 
Friday, except Federal holidays. The AD docket contains this AD, the 
regulatory evaluation, any comments received, and other information. 
The street address for the Docket Operations office (telephone 800-647-
5527) is in the ADDRESSES section.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S. C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2014-16-26 Dassault Aviation: Amendment 39-17950. Docket No. FAA-
2014-0258; Directorate Identifier 2013-NM-065-AD.

(a) Effective Date

    This AD becomes effective October 1, 2014.

(b) Affected ADs

    This AD affects AD 2002-23-20, Amendment 39-12964 (67 FR 71098, 
November 29, 2002); and AD 2010-26-05, Amendment 39-16544 (75 FR 
79952, December 21, 2010).

(c) Applicability

    This AD applies to Dassault Aviation Model FALCON 900EX 
airplanes, certificated in any category, serial numbers 1 through 96 
inclusive, and serial numbers 98 through 119 inclusive.

(d) Subject

    Air Transport Association (ATA) of America Code 05, Time Limits/
Maintenance Checks.

(e) Reason

    This AD was prompted by our determination to introduce a 
corrosion prevention control program, among other changes, to the 
maintenance requirements and airworthiness limitations. We are 
issuing this AD to prevent reduced structural integrity and reduced 
controllability of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Revision of Maintenance or Inspection Program

    Within 30 days after the effective date of this AD, revise the 
maintenance or inspection program, as applicable, to incorporate the 
information specified in Chapter 5-40, Airworthiness Limitations, 
DGT 113874, Revision 12, dated September 2012, of the Falcon 900EX 
Maintenance Manual. The initial compliance time for accomplishing 
the actions specified in Chapter 5-40, Airworthiness Limitations, 
DGT 113874, Revision 12, dated September 2012, of the Falcon 900EX 
Maintenance Manual, is within the applicable times specified in the 
maintenance manual, or 30 days after the effective date of this AD, 
whichever occurs later, except as provided by paragraphs (g)(1) 
through (g)(4) of this AD.
    (1) The term ``LDG'' in the ``First Inspection'' column of any 
table in the service information means total airplane landings.
    (2) The term ``FH'' in the ``First Inspection'' column of any 
table in the service information means total flight hours.
    (3) The term ``FC'' in the ``First Inspection'' column of any 
table in the service information means total flight cycles.
    (4) The term ``M'' in the ``First Inspection'' column of any 
table in the service information means months.

(h) Terminating Action

    Accomplishing paragraph (g) of this AD terminates the 
requirements of AD 2002-23-20, Amendment 39-12964 (67 FR 71098, 
November 29, 2002); and paragraph (g)(1) of AD 2010-26-05, Amendment 
39-16544 (75 FR 79952, December 21, 2010); for Dassault Aviation 
Model FALCON 900EX airplanes, serial numbers 1 through 96 inclusive, 
and serial numbers 98 through 119 inclusive.

(i) No Alternative Actions and Intervals

    After accomplishing the revision required by paragraph (g) of 
this AD, no alternative actions (e.g., inspections) or intervals may 
be used unless the actions or intervals are approved as an 
alternative method of compliance (AMOC) in accordance with the 
procedures specified in paragraph (j)(1) of this AD.

(j) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
has the authority to approve AMOCs for this AD, if requested using 
the procedures found in 14 CFR 39.19. In accordance with 14 CFR 
39.19, send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Branch, send it to ATTN: Tom 
Rodriguez, Aerospace Engineer, International Branch, ANM-116, 
Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, 
WA 98057-3356; telephone 425-227-1137; fax 425-227-1149. Information 
may be emailed to: <a href="/cdn-cgi/l/email-protection#a1988ce0efec8c9090978ce0eceee28cf3e4f0f4e4f2f5f2e1c7c0c08fc6ced7"><span class="__cf_email__" data-cfemail="053c28444b48283434332844484a46285740545040565156456364642b626a73">[email&#160;protected]</span></a>. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager of the local flight 
standards district office/certificate holding district office. The 
AMOC approval letter must specifically reference this AD.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, International 
Branch, ANM-116, Transport Airplane Directorate, FAA; or the 
European Aviation Safety Agency (EASA); or Dassault Aviation's EASA 
Design Organization Approval (DOA). If approved by the DOA, the 
approval must include the DOA-authorized signature.

(k) Related Information

    Refer to Mandatory Continuing Airworthiness Information (MCAI) 
EASA Airworthiness Directive 2013-0051, dated March 4, 2013, for 
related information. This MCAI may be found in the AD docket on the 
Internet at <a href="http://www.regulations.gov/#!documentDetail">http://www.regulations.gov/#!documentDetail</a>;D=FAA-2014-
0258-0002.

(l) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) Chapter 5-40, Airworthiness Limitations, DGT 113874, 
Revision 12, dated September 2012, of the Falcon 900EX Maintenance 
Manual. The document revision level is identified only on the title 
page and page 2.
    (ii) Reserved.
    (3) For service information identified in this AD, contact 
Dassault Falcon Jet, P.O. Box

[[Page 51080]]

2000, South Hackensack, NJ 07606; telephone 201-440-6700; Internet 
<a href="http://www.dassaultfalcon.com">http://www.dassaultfalcon.com</a>.
    (4) You may view this service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For 
information on the availability of this material at the FAA, call 
425-227-1221.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: <a href="http://www.archives.gov/federal-register/cfr/ibr-locations.html">http://www.archives.gov/federal-register/cfr/ibr-locations.html</a>.

    Issued in Renton, Washington, on August 7, 2014.
Victor Wicklund,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2014-19678 Filed 8-26-14; 8:45 am]
BILLING CODE 4910-13-P