AD 2014-05-04
Applicability
| Type | Manufacturer | Model | Details |
|---|---|---|---|
| aircraft | Airbus Helicopters Deutschland GmbH | MBB-BK 117 C-2 | Airworthiness Directives; Eurocopter Deutschland GmbH Helicopters |
Unsafe Condition
The door detaching uncommanded from the fuselage, which could result in the in-flight loss of the door, damaging the helicopter or causing injury or damage on the ground.
AI-generated summary from the source AD text. Verify against the official source before acting.
Required Actions
Visually inspect each door lock release assembly for frayed cables, stripped threads, pitting, and correct installation. Replace damaged parts with airworthy parts. Inspect middle and upper lever locking bolts for correct installation. Install the aft cover and aft inner handle.
AI-generated summary from the source AD text. Verify against the official source before acting.
Compliance Time
Within 50 hours time-in-service
AI-generated summary from the source AD text. Verify against the official source before acting.
Affected Aircraft
Eurocopter Deutschland GmbH Model MBB-BK 117 C-2 helicopters with a jettisonable sliding door installed.
AI-generated summary from the source AD text. Verify against the official source before acting.
Federal Register Abstract
We are adopting a new airworthiness directive (AD) for Eurocopter Deutschland GmbH (Eurocopter) Model MBB-BK 117 C-2 helicopters with a jettisonable sliding door (door) installed. This AD requires inspecting the lock release assembly and the middle and upper lever locking bolts of each door, replacing any damaged parts with airworthy parts, and ensuring the door is correctly installed. This AD was prompted by the uncommanded detaching of a door from an MBB-BK 117 C-2 fuselage. The actions of this AD are intended to prevent the in- flight loss of the door, which could damage the helicopter and injure persons on the ground.
Document Text
Show stored source text (verify against official source)
[Federal Register Volume 79, Number 46 (Monday, March 10, 2014)]
[Rules and Regulations]
[Pages 13204-13206]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2014-04571]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2013-0642; Directorate Identifier 2011-SW-035-AD;
Amendment 39-17777; AD 2014-05-04]
RIN 2120-AA64
Airworthiness Directives; Eurocopter Deutschland GmbH Helicopters
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: We are adopting a new airworthiness directive (AD) for
Eurocopter Deutschland GmbH (Eurocopter) Model MBB-BK 117 C-2
helicopters with a jettisonable sliding door (door) installed. This AD
requires inspecting the lock release assembly and the middle and upper
lever locking bolts of each door, replacing any damaged parts with
airworthy parts, and ensuring the door is correctly installed. This AD
was prompted by the uncommanded detaching of a door from an MBB-BK 117
C-2 fuselage. The actions of this AD are intended to prevent the in-
flight loss of the door, which could damage the helicopter and injure
persons on the ground.
DATES: This AD is effective April 14, 2014.
The Director of the Federal Register approved the incorporation by
reference of a certain document listed in this AD as of April 14, 2014.
ADDRESSES: For service information identified in this AD, contact
American Eurocopter Corporation, 2701 N. Forum Drive, Grand Prairie, TX
75052; telephone (972) 641-0000 or (800) 232-0323; fax (972) 641-3775;
or at <a href="http://www.eurocopter.com/techpub">http://www.eurocopter.com/techpub</a>. You may review the referenced
service information at the FAA, Office of the Regional Counsel,
Southwest Region, 2601 Meacham Blvd., Room 663, Fort Worth, Texas
76137.
Examining the AD Docket
You may examine the AD docket on the Internet at <a href="http://www.regulations.gov">http://www.regulations.gov</a> or in person at the Docket Operations Office
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains this AD, the foreign authority's AD,
any incorporated-by-reference service information, the economic
evaluation, any comments received, and other information. The street
address for the Docket Operations Office (phone: 800-647-5527) is U.S.
Department of Transportation, Docket Operations Office, M-30, West
Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE.,
Washington, DC 20590.
FOR FURTHER INFORMATION CONTACT: Matt Fuller, Senior Aviation Safety
Engineer, Safety Management Group, Rotorcraft Directorate, FAA, 2601
Meacham Blvd., Fort Worth, Texas 76137; telephone (817) 222-5110; email
<a href="/cdn-cgi/l/email-protection#365b5742425e53411850435a5a53447650575718515940"><span class="__cf_email__" data-cfemail="c7aaa6b3b3afa2b0e9a1b2ababa2b587a1a6a6e9a0a8b1">[email protected]</span></a>.
SUPPLEMENTARY INFORMATION:
Discussion
On July 23, 2013, at 78 FR 44039, the Federal Register published
our notice of proposed rulemaking (NPRM), which proposed to amend 14
CFR part 39 by adding an AD that would apply to Model MBB-BK 117 C-2
helicopters with a jettisonable door installed. The NPRM proposed to
require inspecting the lock release assembly and the middle and upper
lever locking bolts of each door, replacing any damaged parts with
airworthy parts, and ensuring the door is correctly installed. The
proposed requirements were intended to prevent the in-flight loss of
the door, which could damage the helicopter and injure persons on the
ground.
The NPRM was prompted by AD No. 2011-0107, dated June 7, 2011,
issued by the European Aviation Safety Agency (EASA), which is the
Technical Agent for the Member States of the European Union. AD No.
2011-0107 was issued to correct an unsafe condition for Eurocopter
Model MBB-BK 117 C-2 helicopters with jettisonable sliding doors
installed. EASA states that in early 2010 it received a report that the
door guides of the jettison mechanism on an MBB-BK 117 C-2 helicopter
released uncommanded while the door was being opened, resulting in the
door detaching from the fuselage. EASA has determined that ``this
condition, if not detected and corrected, could result in cases of in-
flight loss of the jettisonable door, possibly resulting in damage to,
or loss of control of, the helicopter, or injury to persons on the
ground.'' As a result, EASA requires repetitive inspections for the
correct installation of the doors, door guides, and release cables.
Comments
We gave the public the opportunity to participate in developing
this AD, but we received no comments on the NPRM (78 FR 44039, July 23,
2013).
FAA's Determination
These helicopters have been approved by the aviation authority of
Germany and are approved for operation in the United States. Pursuant
to our bilateral agreement with Germany, EASA, its technical
representative, has notified us of the unsafe condition described in
the EASA AD. We are issuing this AD because we evaluated all
information provided by EASA and determined the unsafe condition exists
and is likely to exist or develop on other helicopters of these same
type designs and that air safety and the public interest require
adopting the AD requirements as proposed.
Differences Between This AD and the EASA AD
This AD requires that the inspections be conducted within 50 hours
time-in-service (TIS). The EASA AD requires that the inspections be
conducted within 50 hours TIS or 60 days, whichever occurs first after
the effective date of the EASA AD.
The EASA AD requires that you contact Eurocopter to determine
corrective action, and this AD does not.
The EASA AD requires a repetitive inspection, each time when the
installation of the door guides for the jettisonable sliding doors is
accomplished. This AD does not require this repetitive inspection
because that is considered normal maintenance.
Related Service Information
We reviewed Eurocopter Alert Service Bulletin MBB-BK117 C-2-52A-
015, Revision 0, dated April 26, 2011 (ASB), for Model MBB-BK 117 C-2
helicopters with jettisonable sliding doors installed. The ASB calls
for inspecting the lock release assembly for damage and correct
installation and inspecting the middle lever and upper lever locking
bolts for correct installation. The ASBs require the inspections to be
conducted within 50 hours TIS or two months, whichever occurs first,
and thereafter after every door guide installation.
[[Page 13205]]
Costs of Compliance
We estimate that this AD affects 108 helicopters of U.S. Registry
and that labor costs average $85 a work-hour. Based on these estimates,
we expect the following costs:
<bullet> Visually inspecting the door's lock release assembly and
the middle and upper levers requires 4 work-hours for a labor cost of
$340 per helicopter. No parts are needed, so that the total cost for
the U.S. fleet is $36,720.
<bullet> Visually inspecting all hardware, guides and door
attachment points for misaligned or bent fittings requires 4 work-hours
for a labor cost of $340 per helicopter. Parts may be needed but on an
individual basis, so that the total cost for the U.S. fleet is at least
$36,720.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on helicopters identified in this
rulemaking action.
Regulatory Findings
This AD will not have federalism implications under Executive Order
13132. This AD will not have a substantial direct effect on the States,
on the relationship between the national government and the States, or
on the distribution of power and responsibilities among the various
levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866;
(2) Is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979);
(3) Will not affect intrastate aviation in Alaska to the extent
that it justifies making a regulatory distinction; and
(4) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared an economic evaluation of the estimated costs to comply
with this AD and placed it in the AD docket.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive (AD):
2014-05-04 Eurocopter Deutschland GmbH (Eurocopter): Amendment 39-
17777; Docket No. FAA-2013-0642; Directorate Identifier 2011-SW-035-
AD.
(a) Applicability
This AD applies to Model MBB-BK 117 C-2 helicopters with a
jettisonable main cabin sliding door (door) installed, certificated
in any category.
(b) Unsafe Condition
This AD defines the unsafe condition as the door detaching
uncommanded from the fuselage. This condition could result in the
in-flight loss of the door, which could damage the helicopter or
cause injury or damage on the ground.
(c) Effective Date
This AD becomes effective April 14, 2014.
(d) Compliance
You are responsible for performing each action required by this
AD within the specified compliance time unless it has already been
accomplished prior to that time.
(e) Required Actions
Within 50 hours time-in-service:
(1) Visually inspect each door lock release assembly for a
frayed cable, a stripped thread on a screw joint, pitting on a door
guide, release cable, or associated hardware, and for correct
installation by following the Accomplishment Instructions, paragraph
3.B.1. (a) through (c), except (c)(1) and (c)(2), of Eurocopter
Alert Service Bulletin MBB-BK117 C-2-52A-015, Revision 0, dated
April 26, 2011 (ASB).
(i) Replace with an airworthy part any frayed cables, screw
joints with stripped threads, or any door guides, release cables,
and associated hardware with pitting. Allow for a minimum of one
millimeter clearance at each end of the release cables.
(ii) Install the aft cover and aft inner handle.
(2) Inspect each middle lever and upper lever locking bolt for
correct installation by following the Accomplishment Instructions,
paragraphs 3.B.2 and 3.B.3, of the ASB, except that we do not
require you to contact Eurocopter.
(3) If the door cannot be correctly rigged after performing the
actions required by paragraph (e)(2) of this AD, inspect all
hardware, guides, and door attachment points for misalignment or
bent fittings. Replace misaligned or bent parts with airworthy parts
before you operate the door in-flight and re-inspect according to
the requirements in paragraph (e)(2) of this AD.
(f) Special Flight Permits
A one-time flight to a maintenance facility is permitted
provided that the door is not opened in flight.
(g) Alternative Methods of Compliance (AMOCs)
(1) The Manager, Safety Management Group, FAA, may approve AMOCs
for this AD. Send your proposal to: Matt Fuller, Senior Aviation
Safety Engineer, Safety Management Group, Rotorcraft Directorate,
FAA, 2601 Meacham Blvd., Fort Worth, Texas 76137; telephone (817)
222-5110; email <a href="/cdn-cgi/l/email-protection#04696570706c61732a627168686176446265652a636b72"><span class="__cf_email__" data-cfemail="066b6772726e63712860736a6a63744660676728616970">[email protected]</span></a>.
(2) For operations conducted under a 14 CFR part 119 operating
certificate or under 14 CFR part 91, subpart K, we suggest that you
notify your principal inspector, or lacking a principal inspector,
the manager of the local flight standards district office or
certificate holding district office, before operating any aircraft
complying with this AD through an AMOC.
(h) Additional Information
The subject of this AD is addressed in European Aviation Safety
Agency (EASA) AD No. 2011-0107, dated June 7, 2011. You may view the
EASA AD on the Internet at <a href="http://www.regulations.gov">http://www.regulations.gov</a> in Docket No.
FAA-2013-0642.
(i) Subject
Joint Aircraft Service Component (JASC) Code: 5200, Doors.
(j) Material Incorporated by Reference
(1) The Director of the Federal Register approved the
incorporation by reference (IBR) of the service information listed
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this service information as applicable to do
the actions required by this AD, unless the AD specifies otherwise.
(i) Eurocopter Alert Service Bulletin MBB-BK117 C-2-52A-015,
Revision 0, dated April 26, 2011.
(ii) Reserved.
(3) For Eurocopter service information identified in this AD,
contact American Eurocopter Corporation, 2701 N. Forum Drive, Grand
Prairie, TX 75052; telephone (972) 641-0000 or (800) 232-0323; fax
(972) 641-3775; or at <a href="http://www.eurocopter.com/techpub">http://www.eurocopter.com/techpub</a>.
(4) You may view this service information at FAA, Office of the
Regional Counsel,
[[Page 13206]]
Southwest Region, 2601 Meacham Blvd., Room 663, Fort Worth, Texas
76137. For information on the availability of this material at the
FAA, call (817) 222-5110.
(5) You may view this service information that is incorporated
by reference at the National Archives and Records Administration
(NARA). For information on the availability of this material at
NARA, call (202) 741-6030, or go to: <a href="http://www.archives.gov/federal-register/cfr/ibr-locations.html">http://www.archives.gov/federal-register/cfr/ibr-locations.html</a>.
Issued in Fort Worth, Texas, on February 20, 2014.
Lance T. Gant,
Acting Directorate Manager, Rotorcraft Directorate, Aircraft
Certification Service.
[FR Doc. 2014-04571 Filed 3-7-14; 8:45 am]
BILLING CODE 4910-13-P
Source: Official FAA Source ↗
Retrieved: Apr 4, 2026
Rights: U.S. Government Public Domain
This site is not affiliated with or endorsed by the FAA. Always verify with official sources.