AD 2012-25-01
Applicability
| Type | Manufacturer | Model | Details |
|---|---|---|---|
| aircraft | Airbus Helicopters | AS355E | Airworthiness Directives; Eurocopter France Helicopters |
| aircraft | Airbus Helicopters | AS355F | Airworthiness Directives; Eurocopter France Helicopters |
| aircraft | Airbus Helicopters | AS355F1 | Airworthiness Directives; Eurocopter France Helicopters |
| aircraft | Airbus Helicopters | AS355F2 | Airworthiness Directives; Eurocopter France Helicopters |
| aircraft | Airbus Helicopters | AS355N | Airworthiness Directives; Eurocopter France Helicopters |
| aircraft | Airbus Helicopters | AS355NP | Airworthiness Directives; Eurocopter France Helicopters |
| aircraft | Airbus Helicopters | AS350B | Airworthiness Directives; Eurocopter France Helicopters |
| aircraft | Airbus Helicopters | AS350B1 | Airworthiness Directives; Eurocopter France Helicopters |
| aircraft | Airbus Helicopters | AS350B2 | Airworthiness Directives; Eurocopter France Helicopters |
| aircraft | Airbus Helicopters | AS350B3 | Airworthiness Directives; Eurocopter France Helicopters |
| aircraft | Airbus Helicopters | AS350BA | Airworthiness Directives; Eurocopter France Helicopters |
| aircraft | Airbus Helicopters | AS350C | Airworthiness Directives; Eurocopter France Helicopters |
| aircraft | Airbus Helicopters | AS350D | Airworthiness Directives; Eurocopter France Helicopters |
| aircraft | Airbus Helicopters | AS350D1 | Airworthiness Directives; Eurocopter France Helicopters |
Unsafe Condition
A crack in an attachment bracket of the emergency flotation gear could result in failure of the emergency flotation system and loss of float stability in the event of a water landing.
AI-generated summary from the source AD text. Verify against the official source before acting.
Required Actions
Visually inspect the front and rear emergency flotation gear attachment brackets using a 5X or higher power magnifying glass. If a crack is found, replace the cracked bracket with an airworthy bracket. Perform the initial inspection within 110 hours time-in-service or 3 months, whichever occurs first, and repeat inspections at intervals not to exceed 13 months.
AI-generated summary from the source AD text. Verify against the official source before acting.
Compliance Time
Within 110 hours time-in-service or 3 months, whichever occurs first, and thereafter at intervals not to exceed 13 months.
AI-generated summary from the source AD text. Verify against the official source before acting.
Affected Aircraft
Eurocopter France Model AS350B, AS350BA, AS350B1, AS350B2, AS350B3, AS350C, AS350D, AS350D1, AS355E, AS355F, AS355F1, AS355F2, AS355N, and AS355NP helicopters with an Aerazur emergency flotation gear attachment bracket, part number 158172, 158173, 158288, or 158289, installed.
AI-generated summary from the source AD text. Verify against the official source before acting.
Federal Register Abstract
We are adopting a new airworthiness directive (AD) for Eurocopter France Model AS350B, AS350BA, AS350B1, AS350B2, AS350B3, AS350C, AS350D, AS350D1, AS355E, AS355F, AS355F1, AS355F2, AS355N, and AS355NP helicopters with certain Aerazur emergency flotation gear attachment brackets (brackets) installed. This AD requires an initial and recurring inspection of the brackets for a crack, and if there is a crack, replacing the cracked bracket with an airworthy bracket. This AD was prompted by reports of cracks on the brackets. The actions of this AD are intended to prevent failure of the emergency flotation system and loss of float stability in the event of a water landing.
Document Text
Show stored source text (verify against official source)
[Federal Register Volume 78, Number 84 (Wednesday, May 1, 2013)]
[Rules and Regulations]
[Pages 25367-25369]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2013-09437]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2012-0631; Directorate Identifier 2011-SW-021-AD;
Amendment 39-17282; AD 2012-25-01]
RIN 2120-AA64
Airworthiness Directives; Eurocopter France Helicopters
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: We are adopting a new airworthiness directive (AD) for
Eurocopter France Model AS350B, AS350BA, AS350B1, AS350B2, AS350B3,
AS350C, AS350D, AS350D1, AS355E, AS355F, AS355F1, AS355F2, AS355N, and
AS355NP helicopters with certain Aerazur emergency flotation gear
attachment brackets (brackets) installed. This AD requires an initial
and recurring inspection of the brackets for a crack, and if there is a
crack, replacing the cracked bracket with an airworthy bracket. This AD
was prompted by reports of cracks on the brackets. The actions of this
AD are intended to prevent failure of the emergency flotation system
and loss of float stability in the event of a water landing.
DATES: This AD is effective June 5, 2013.
The Director of the Federal Register approved the incorporation by
reference of certain documents listed in this AD as of June 5, 2013.
ADDRESSES: For service information identified in this AD, contact
American Eurocopter Corporation, 2701 N. Forum
[[Page 25368]]
Drive, Grand Prairie, TX 75052; telephone (972) 641-0000 or (800) 232-
0323; fax (972) 641-3775; or at <a href="http://www.eurocopter.com/techpub">http://www.eurocopter.com/techpub</a>. You
may review the referenced service information at the FAA, Office of the
Regional Counsel, Southwest Region, 2601 Meacham Blvd., Room 663, Fort
Worth, Texas 76137.
Examining the AD Docket
You may examine the AD docket on the Internet at <a href="http://www.regulations.gov">http://www.regulations.gov</a> or in person at the Docket Operations Office
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains this AD, any incorporated-by-reference
service information, the economic evaluation, any comments received,
and other information. The street address for the Docket Operations
Office (phone: 800-647-5527) is U.S. Department of Transportation,
Docket Operations Office, M-30, West Building Ground Floor, Room W12-
140, 1200 New Jersey Avenue SE., Washington, DC 20590.
FOR FURTHER INFORMATION CONTACT: Robert Grant, Aviation Safety
Engineer, Safety Management Group, FAA, 2601 Meacham Blvd., Fort Worth,
Texas 76137; telephone (817) 222-5110; email <a href="/cdn-cgi/l/email-protection#0c7e636e697e78226b7e6d62784c6a6d6d226b637a"><span class="__cf_email__" data-cfemail="cdbfa2afa8bfb9e3aabfaca3b98dabacace3aaa2bb">[email protected]</span></a>.
SUPPLEMENTARY INFORMATION:
Discussion
On June 18, 2012, at 77 FR 36216, the Federal Register published
our notice of proposed rulemaking (NPRM), which proposed to amend 14
CFR part 39 to include an AD that would apply to Eurocopter France
Model AS350B, AS350BA, AS350B1, AS350B2, AS350B3, AS350C, AS350D,
AS350D1, AS355E, AS355F, AS355F1, AS355F2, AS355N, and AS355NP
helicopters with a bracket, part number (P/N) 158172, 158173, 158288,
or 158289, installed. That NPRM proposed to require an initial and
recurring inspection of the brackets for a crack, and if there was a
crack, replacing the cracked bracket with an airworthy bracket. The
proposed requirements were intended to prevent failure of the emergency
flotation system and loss of float stability in the event of a water
landing.
The European Aviation Safety Agency (EASA), which is the Technical
Agent for the Member States of the European Union, issued EASA AD No.
2011-0072, dated April 20, 2011 (AD 2011-0072), to correct an unsafe
condition for the Eurocopter AS350B, AS350BA, AS350BB, AS350B1,
AS350B2, AS350B3, AS350D, AS355E, AS355F, AS355F1, AS355F2, AS355N, and
AS355NP helicopters with Aerazur emergency flotation gear attachments
installed. EASA stated it received several reports of cracks being
found on the brackets which appear to be caused by stress corrosion.
This condition, if not corrected, could result in ``rupture of the
emergency flotation gear attachment brackets'' during a water landing.
The helicopter's float stability could no longer be ensured, possibly
resulting in damage to the helicopter and injury to the occupants.
EASA's AD requires an initial inspection of the brackets, replacement
of any brackets found with cracks, and re-inspection of the brackets
every 13 months.
Comments
We gave the public the opportunity to participate in developing
this AD, but we received no comments on the NPRM (77 FR 36216, June 18,
2012).
FAA's Determination
These helicopters have been approved by the aviation authority of
France and are approved for operation in the United States. Pursuant to
our bilateral agreement with France, EASA, its technical
representative, has notified us of the unsafe condition described in
the EASA AD. We are issuing this AD because we evaluated all
information provided by EASA and determined the unsafe condition exists
and is likely to exist or develop on other helicopters of these same
type designs and that air safety and the public interest require
adopting the AD requirements as proposed except we are incorporating a
figure by reference instead of including it in our AD to meet current
publication requirements. This change is consistent with the intent of
the proposals in the NPRM (77 FR 36216, June 18, 2012) and will not
increase the economic burden on any operator nor increase the scope of
the AD.
Interim Action
We consider this AD interim action. Eurocopter is developing a
modification that will address the unsafe condition identified in this
AD. Once this modification is developed, approved, and available, we
might consider additional rulemaking.
Differences Between This AD and the EASA AD
Differences between this AD and the EASA AD include:
<bullet> The EASA AD applies to Eurocopter Model AS 350 BB
helicopters. This AD does not as this model is not type certificated by
the FAA. Additionally, the EASA AD excludes Eurocopter Models AS350C
and AS350D1, whereas this AD includes them.
<bullet> The EASA AD mandates different compliance times depending
on the manufacture date of the helicopter. We mandate inspecting all
helicopters within 110 hours TIS or 3 months, whichever occurs first,
regardless of date of manufacture.
<bullet> This AD does not require returning cracked brackets to the
manufacturer.
Related Service Information
Eurocopter issued Alert Service Bulletin (ASB) No. AS350-05.00.63,
Revision 1, dated April 18, 2011, and ASB No. AS355-05.00.58, Revision
1, dated April 18, 2011. These ASBs specify procedures to inspect the
front and rear brackets at regular intervals. EASA classified these
ASBs as mandatory and issued EASA AD 2011-0072 to ensure the continued
airworthiness of these helicopters.
Costs of Compliance
We estimate that this AD will affect 733 helicopters of U.S.
Registry and that labor rates will average $85 an hour. Inspecting the
brackets will take about 4 work-hours per inspection cycle for a labor
cost of $340 per helicopter and $249,220 for the U.S. fleet. Replacing
the bracket, if needed, will require about 1 work-hour and about $1,130
for the parts. Thus, the total cost to replace one bracket will be
about $1,215.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on helicopters identified in this
rulemaking action.
Regulatory Findings
This AD will not have federalism implications under Executive Order
13132. This AD will not have a substantial direct effect on the States,
on the relationship between the national
[[Page 25369]]
government and the States, or on the distribution of power and
responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866;
(2) Is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979);
(3) Will not affect intrastate aviation in Alaska to the extent
that it justifies making a regulatory distinction; and
(4) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared an economic evaluation of the estimated costs to comply
with this AD and placed it in the AD docket.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive (AD):
2012-25-01 Eurocopter France: Amendment 39-17282; Docket No. FAA-
2012-0631; Directorate Identifier 2011-SW-021-AD.
(a) Applicability
This AD applies to Eurocopter France Model AS350B, AS350BA,
AS350B1, AS350B2, AS350B3, AS350C, AS350D, AS350D1, AS355E, AS355F,
AS355F1, AS355F2, AS355N, and AS355NP helicopters with an Aerazur
emergency flotation gear attachment bracket, part number 158172,
158173, 158288, or 158289, installed, certificated in any category.
(b) Unsafe Condition
This AD defines the unsafe condition as a crack in an attachment
bracket of the emergency flotation gear. This condition could result
in failure of the emergency flotation system and loss of float
stability in the event of a water landing.
(c) Effective Date
This AD becomes effective June 5, 2013.
(d) Compliance
You are responsible for performing each action required by this
AD within the specified compliance time unless accomplished
previously.
(e) Required Actions
Within 110 hours time-in-service or 3 months, whichever occurs
first, and thereafter at intervals not to exceed 13 months:
(1) Using a 5X or higher power magnifying glass, visually
inspect the front emergency floatation gear attachment bracket,
section B-B, item (e) in Areas F, G, and H of Figure 1 of Eurocopter
Alert Service Bulletin No. AS350-05.00.63 or No. AS355-05.00.58,
both Revision 1, and both dated April 18, 2011, as applicable to
your model helicopter (ASB); and the rear emergency flotation gear
attachment bracket, section A-A, item (a) in Areas D and E of Figure
1 of the ASB, for a crack.
(2) If there is a crack, replace the cracked emergency
floatation gear attachment bracket with an airworthy emergency
floatation gear attachment bracket prior to reinstallation of the
emergency flotation equipment.
(f) Alternative Methods of Compliance (AMOCs)
(1) The Manager, Safety Management Group, FAA, may approve AMOCs
for this AD. Send your proposal to: Robert Grant, Aviation Safety
Engineer, Safety Management Group, FAA, 2601 Meacham Blvd., Fort
Worth, Texas 76137; telephone (817) 222-5110; email
<a href="/cdn-cgi/l/email-protection#8ffde0edeafdfba1e8fdeee1fbcfe9eeeea1e8e0f9"><span class="__cf_email__" data-cfemail="c5b7aaa7a0b7b1eba2b7a4abb185a3a4a4eba2aab3">[email protected]</span></a>.
(2) For operations conducted under a 14 CFR part 119 operating
certificate or under 14 CFR part 91, subpart K, we suggest that you
notify your principal inspector, or lacking a principal inspector,
the manager of the local flight standards district office or
certificate holding district office, before operating any aircraft
complying with this AD through an AMOC.
(g) Additional Information
The subject of this AD is addressed in European Aviation Safety
Agency AD No. 2011-0072, dated April 20, 2011.
(h) Subject
Joint Aircraft Service Component (JASC) Code: 2560, Emergency
Equipment.
(i) Material Incorporated by Reference
(1) The Director of the Federal Register approved the
incorporation by reference (IBR) of the service information listed
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this service information as applicable to do
the actions required by this AD, unless the AD specifies otherwise.
(i) Eurocopter Alert Service Bulletin (ASB) No. AS350-05.00.63,
Revision 1, dated April 18, 2011.
(ii) Eurocopter ASB No. AS355-05.00.58, Revision 1, dated April
18, 2011.
(3) For Eurocopter service information identified in this AD,
contact American Eurocopter Corporation, 2701 N. Forum Drive, Grand
Prairie, Texas 75052; telephone (972) 641-0000 or (800) 232-0323;
fax (972) 641-3775; or at <a href="http://www.eurocopter.com/techpub">http://www.eurocopter.com/techpub</a>.
(4) You may view this service information at FAA, Office of the
Regional Counsel, Southwest Region, 2601 Meacham Blvd., Room 663,
Fort Worth, Texas 76137. For information on the availability of this
material at the FAA, call (817) 222-5110.
(5) You may view this service information that is incorporated
by reference at the National Archives and Records Administration
(NARA). For information on the availability of this material at
NARA, call (202) 741-6030, or go to: <a href="http://www.archives.gov/federal-register/cfr/ibr-locations.html">http://www.archives.gov/federal-register/cfr/ibr-locations.html</a>.
Issued in Fort Worth, Texas, on April 12, 2013.
Lance T. Gant,
Acting Directorate Manager, Rotorcraft Directorate, Aircraft
Certification Service.
[FR Doc. 2013-09437 Filed 4-30-13; 8:45 am]
BILLING CODE 4910-13-P
Source: Official FAA Source ↗
Retrieved: Apr 6, 2026
Rights: U.S. Government Public Domain
This site is not affiliated with or endorsed by the FAA. Always verify with official sources.