AD 2009-20-02
Applicability
| Type | Manufacturer | Model | Details |
|---|---|---|---|
| aircraft | The Boeing Company | 767-200 Series | Airworthiness Directives; Boeing Model 767-200 and -300 Series Airplanes |
| aircraft | The Boeing Company | 767-300 Series | Airworthiness Directives; Boeing Model 767-200 and -300 Series Airplanes |
Unsafe Condition
Escape slides and slide-rafts of the forward and mid-cabin entry and service doors may be too steep for evacuation in the event that the airplane rotates onto the aft fuselage into the extreme tip-back condition, potentially causing injury to passengers and crewmembers during an emergency evacuation.
AI-generated summary from the source AD text. Verify against the official source before acting.
Required Actions
Replace certain door-mounted escape slides and slide-raft assemblies with new slide-raft assemblies. Replace certain escape system latches with new latches. Modify or replace certain counterbalance assemblies with new counterbalance assemblies. Adjust the door counterbalance system as applicable.
AI-generated summary from the source AD text. Verify against the official source before acting.
Compliance Time
Within 96 months of the effective date (November 3, 2009).
AI-generated summary from the source AD text. Verify against the official source before acting.
Affected Aircraft
Boeing Model 767-200 and -300 series airplanes, as identified in Boeing Service Bulletin 767-25A0266, Revision 3, dated July 3, 2008.
AI-generated summary from the source AD text. Verify against the official source before acting.
Federal Register Abstract
This amendment adopts a new airworthiness directive (AD), applicable to certain Boeing Model 767-200 and -300 series airplanes, that requires replacing certain door-mounted escape slides and slide- raft assemblies with new slide-raft assemblies. This AD also requires the following actions, as applicable: replacing certain escape system latches with new latches; modifying or replacing certain counterbalance assemblies with new counterbalance assemblies; and adjusting the door counterbalance system. The actions specified by this AD are intended to prevent the escape slides and slide-rafts of the forward and mid-cabin entry and service doors from being too steep for evacuation in the event that the airplane rotates onto the aft fuselage into the extreme tip-back condition. In the extreme tip-back condition, the forward and mid-cabin exits could result in steeper sliding angles, which could cause injury to passengers and crewmembers during an emergency evacuation. This action is intended to address the identified unsafe condition.
Document Text
Show stored source text (verify against official source)
[Federal Register Volume 74, Number 187 (Tuesday, September 29, 2009)]
[Rules and Regulations]
[Pages 49798-49801]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: E9-22668]
[[Page 49798]]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2008-0682; Directorate Identifier 2001-NM-237-AD;
Amendment 39-16025; AD 2009-20-02]
RIN 2120-AA64
Airworthiness Directives; Boeing Model 767-200 and -300 Series
Airplanes
AGENCY: Federal Aviation Administration, DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: This amendment adopts a new airworthiness directive (AD),
applicable to certain Boeing Model 767-200 and -300 series airplanes,
that requires replacing certain door-mounted escape slides and slide-
raft assemblies with new slide-raft assemblies. This AD also requires
the following actions, as applicable: replacing certain escape system
latches with new latches; modifying or replacing certain counterbalance
assemblies with new counterbalance assemblies; and adjusting the door
counterbalance system. The actions specified by this AD are intended to
prevent the escape slides and slide-rafts of the forward and mid-cabin
entry and service doors from being too steep for evacuation in the
event that the airplane rotates onto the aft fuselage into the extreme
tip-back condition. In the extreme tip-back condition, the forward and
mid-cabin exits could result in steeper sliding angles, which could
cause injury to passengers and crewmembers during an emergency
evacuation. This action is intended to address the identified unsafe
condition.
DATES: Effective November 3, 2009.
The incorporation by reference of a certain publication listed in
the regulations is approved by the Director of the Federal Register as
of November 3, 2009.
ADDRESSES: The service information referenced in this AD may be
obtained from Boeing Commercial Airplanes, Attention: Data & Services
Management, P.O. Box 3707, MC 2H-65, Seattle, Washington 98124-2207;
telephone 206-544-5000, extension 1; fax 206-766-5680; e-mail
<a href="/cdn-cgi/l/email-protection#b3ded69dd1dcd6d0dcdef3d1dcd6daddd49dd0dcde"><span class="__cf_email__" data-cfemail="d8b5bdf6bab7bdbbb7b598bab7bdb1b6bff6bbb7b5">[email protected]</span></a>; Internet <a href="https://www.myboeingfleet.com">https://www.myboeingfleet.com</a>. This
information may be examined at the Federal Aviation Administration
(FAA), Transport Airplane Directorate, Rules Docket, 1601 Lind Avenue,
SW., Renton, Washington. For information on the availability of this
material at the FAA, call 425-227-1221 or 425-227-1152.
You may examine the AD docket on the Internet at <a href="http://www.regulations.gov">http://www.regulations.gov</a>; or in person at the Docket Management Facility
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains this AD, the regulatory evaluation,
any comments received, and other information. The address for the
Docket Office (telephone 800-647-5527) is the Document Management
Facility, U.S. Department of Transportation, Docket Operations, M-30,
West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE.,
Washington, DC 20590.
FOR FURTHER INFORMATION CONTACT: Andrew Guion, Aerospace Engineer,
Cabin Safety and Environmental Systems Branch, ANM-150S, FAA, Seattle
Aircraft Certification Office, 1601 Lind Avenue, SW., Renton,
Washington 98057-3356; telephone (425) 917-6428; fax (425) 917-6590.
SUPPLEMENTARY INFORMATION: A proposal to amend part 39 of the Federal
Aviation Regulations (14 CFR part 39) to include an airworthiness
directive (AD) that is applicable to certain Boeing Model 767-200 and -
300 series airplanes was published as a supplemental notice of proposed
rulemaking (NPRM) in the Federal Register on June 17, 2008 (73 FR
34233). That action proposed to require replacing certain door-mounted
escape slides and slide-raft assemblies with new slide-raft assemblies;
replacing certain escape system latches with new latches; and modifying
or replacing certain counterbalance assemblies with new counterbalance
assemblies; as applicable. The supplemental NPRM also proposed to
extend the compliance time, add requirements to install a longer firing
cable and test the valve of the inflation trigger system of the slide-
raft and, for certain airplanes, add procedures to adjust the door
counterbalance systems.
Explanation of Revised Service Information
Since we issued the supplemental NPRM, we have reviewed Boeing
Service Bulletin 767-25A0266, Revision 3, dated July 3, 2008. We
referred to Boeing Service Bulletin 767-25A0266, Revision 2, dated
September 27, 2007, in the supplemental NPRM as the appropriate source
of service information for replacing the slide-rafts. The procedures in
Revision 2 and Revision 3 are essentially the same; however, Revision 3
corrects certain typographical errors, including certain part numbers
for the slide-rafts.
We have revised paragraph (a) of this AD to refer to Boeing Service
Bulletin 767-25A0266, Revision 3, dated July 3, 2008, as the
appropriate source of service information. We have also included Boeing
Service Bulletin 767-25A0266, Revision 2, dated September 27, 2007, in
Table 1 of this AD to state that actions done before the effective date
of this AD in accordance with Revision 2 are acceptable for compliance
with the requirements of paragraph (a) of this AD.
Comments
Interested persons have been afforded an opportunity to participate
in the making of this amendment. Due consideration has been given to
the comments received.
Requests To Withdraw Supplemental NPRM or Extend Compliance Time
Air Transport Association (ATA), American Airlines, and Delta
Airlines request that we either withdraw the supplemental NPRM or
extend the compliance time for replacing the slide-rafts. All Nippon
Airways requests a compliance time of 8 years (96 months), and ATA
requests a compliance time of 10 years (120 months) rather than the 72
months proposed in the supplemental NPRM.
ATA also cites information to show the improbability of the unsafe
condition, and maintains that we should withdraw the NPRM due to its
lack of potential to add safety benefit, its significantly
disproportional costs, its unjustified compliance period, and the fact
that the intent of the proposal is already being accomplished on an
attrition basis. ATA also states that if the FAA disagrees with its
justifications and proceeds with the final rule, it recommends a 10-
year compliance period for better correlation with risk-management
methods.
American Airlines and ATA further object to the requirement to
replace the slide-rafts. They agree with the manufacturer that the
unsafe condition specified in the supplemental NPRM is not a safety
issue. American Airlines and ATA state that the likelihood that the
scenario described in the supplemental NPRM would result in a time-
limited evacuation is extremely improbable.
We partially agree with the commenters. We do not agree with the
requests to withdraw the supplemental NPRM. We have determined that an
unsafe condition exists. Although the specific conditions addressed in
the supplemental NPRM have not been
[[Page 49799]]
encountered in service, we have received reports of partial tip-back
during accidents/incidents that could have resulted in extreme tip-back
given slightly different conditions, making this type of event
foreseeable. During at least one of these partial tip-back events, the
slides were deployed to facilitate evacuation. We do not agree that the
low probability of encountering such a foreseeable event is
justification to withdraw the supplemental NPRM. We have also
determined that an interval based on the ``useful service life'' of the
slides, which is 15 years, would not address the unsafe condition in a
timely manner.
However, we do agree that it is appropriate to extend the
compliance time. We have determined that a compliance time of 96 months
represents an appropriate interval of time in which the required
actions can be performed, while still maintaining an adequate level of
safety. In developing an appropriate compliance time, we considered the
safety implications, parts availability, and normal maintenance
schedules for timely accomplishment of the modifications. We also
considered the costs to comply with the actions (see updated cost
information in the Costs of Compliance section). The revised compliance
time will allow operators to offset the costs of complying with this AD
with the costs associated with normal slide replacement. Therefore, we
have revised paragraph (a) of this AD to extend the compliance time for
replacing the slide-rafts from 72 months to 96 months.
Requests To Remove Firing Cable Requirement From the Supplemental NPRM
Continental Airlines, Goodrich, and Boeing ask that we remove
paragraph (b), ``Modification of the Firing Cable,'' from the
supplemental NPRM. Delta points out that the requirement to modify the
firing cable is proposed in Docket FAA-2008-0302 (and is now required
by AD 2008-21-05, amendment 39-15689 (73 FR 59486, October 9, 2008)) at
a compliance time of 36 months rather than the 72 months proposed in
the supplemental NPRM. Boeing states that we should also remove the
reference to Boeing Alert Service Bulletin 767-25A0395, dated August
31, 2006, from Table 1 ``Previous Revisions of Service Bulletins,''
because that service bulletin relates to the modification specified in
paragraph (b) of the supplemental NPRM.
We agree with the commenters' requests to remove paragraph (b) of
the supplemental NPRM and the reference to Boeing Alert Service
Bulletin 767-25A0395, dated August 31, 2006. The requirement to modify
the firing cable is already included in AD 2008-21-05. Therefore, we
have revised this AD as requested. The requirement to modify the firing
cable will remain part of AD 2008-21-05, which also includes other
tasks related to the firing cable.
Requests To Revise Cost Impact
Goodrich, and ATA, on behalf of its member American Airlines,
request that we revise the ``Cost Impact'' paragraph. American Airlines
states that we did not include the cost of the slide-rafts in the
original NPRM; as the slide-rafts are the dominant cost of the
modification, ATA and American Airlines state that the cost estimate is
both incomplete and inaccurate. Goodrich points out that the costs in
the supplemental NPRM reflect prices for 2004 and requests that we
revise the cost of the slide-rafts to 2008 prices.
We agree with Goodrich to revise the cost of the slide-rafts to
reflect 2008 prices. The ``Cost Impact'' paragraph below includes the
current price of the slide-rafts. We acknowledge American Airlines'
request, but point out that although the original NPRM did not include
the cost of the slide-rafts, the supplemental NPRM did include those
costs.
Request To Change Applicability
Boeing requests that we change the applicability of the
supplemental NPRM to refer to airplanes identified in Boeing Service
Bulletin 767-25A0266, Revision 3, dated July 3, 2008, rather than
referring only to those Model 767-200 and -300 series airplanes that
have line numbers 1 through 793 inclusive, equipped with door-mounted
escape slide systems. Boeing states that the applicability, as written
in the supplemental NPRM, might make an alternative method of
compliance (AMOC) request necessary for Model 767 door-mounted escape
system part numbers that are not addressed by the proposed AD.
We agree with Boeing for the reasons stated, and have revised the
applicability statement of this AD to include a reference to Boeing
Service Bulletin 767-25A0266, Revision 3, dated July 3, 2008, which
includes specific details about which airplanes are affected by this
AD.
Requests To Extend Comment Period
Delta Airlines and ATA request additional time to review the
supplemental NPRM. Delta requests that we extend the comment period for
an additional 60 days because of the complex nature of the supplemental
NPRM, the inclusion of multiple service bulletins, the extensive
background and significant number of comments in response to the
original NPRM, the hugely significant costs, and the fact that the
original NPRM was thought to have been withdrawn. ATA also requests an
extension of 60 days to the comment period, citing costs and the need
to assess the complex requirements.
We disagree with the requests to provide additional time to comment
on the supplemental NPRM. As Delta points out in their comment, there
was a period of 4.5 years between the release of the original NPRM and
the supplemental NPRM, which gave operators sufficient time to consider
the requirements. We have not changed the AD in this regard.
Request for Industry-Wide Response
Delta Airlines requests that ATA coordinate an industry-wide
response to the supplemental NPRM with the goal of gathering enough
technical information to support its cancellation. Delta states that,
given previous discussions with Boeing regarding risk and probability,
the supplemental NPRM does not appear to have adequate merit. Also,
given the significant cost impact, the industry would be well-served by
opening the time to conduct a coordinated effort to ensure that the
action proposed in the supplemental NPRM is not mandated.
We neither agree nor disagree with the request for ATA to
coordinate an industry-wide response. This comment is directed to ATA
and is beyond the scope of the AD action. We disagree that the
supplemental NPRM does not have adequate merit. We consider the
proposed actions to be an adequate response to an unsafe condition. As
stated previously, although the specific conditions addressed in the
supplemental NPRM have not been encountered, there have been accidents/
incidents that make this type of event foreseeable. We do not agree
that the low probability of encountering such a foreseeable event is
justification for withdrawing the supplemental NPRM. Therefore, we have
not changed the AD in this regard.
As explained previously, we also considered the costs to comply
with the actions proposed in the supplemental NPRM. While we determined
that a compliance time based on the ``useful service life'' of the
slides would not address the unsafe condition in a timely manner, we
did agree to extend the compliance time for replacing the slide-rafts
from 72 months to 96 months. The revised compliance time will allow
[[Page 49800]]
operators to offset the costs of complying with this AD with the costs
associated with normal slide replacement. We have revised paragraph (a)
of this AD to extend the compliance time for replacing the slide-rafts
from 72 months to 96 months.
Conclusion
After careful review of the available data, including the comments
noted above, the FAA has determined that air safety and the public
interest require the adoption of the rule with the changes previously
described. The FAA has determined that these changes will neither
increase the economic burden on any operator nor increase the scope of
the AD.
Cost Impact
There are approximately 745 airplanes of the affected design in the
worldwide fleet. The FAA estimates that 261 airplanes of U.S. registry
are affected by this AD. The work hours and required parts per airplane
vary according to the configuration group to which the affected
airplane belongs. The average labor rate is $80 per work hour. The
``Cost Impact per Airplane Configuration Group'' table shows the
estimated costs.
Cost Impact per Airplane Configuration Group
--------------------------------------------------------------------------------------------------------------------------------------------------------
Fleet cost, by
Airplane configuration group U.S.-registered Work hours Kit cost Slide cost Cost per airplane configuration
airplanes group
--------------------------------------------------------------------------------------------------------------------------------------------------------
1..................................... 208 6 $1,236 $222,002 $223,718 $46,533,334
2..................................... 12 12 2,472 448,502 451,934 5,423,208
3..................................... 41 11 98,858 222,002 321,740 13,191,340
4..................................... 0 11 34,012 222,002 256,894 0
5..................................... 0 17 35,248 448,502 485,110 0
--------------------------------------------------------------------------------------------------------------------------------------------------------
Based on the figures in the ``Cost Impact per Airplane
Configuration Group'' table, the cost impact of this AD on U.S.
operators is estimated to be $65,147,882.
The cost impact figures discussed above are based on assumptions
that no operator has yet accomplished any of the proposed requirements
of this AD action, and that no operator would accomplish those actions
in the future if this AD were not adopted. The cost impact figures
discussed in AD rulemaking actions represent only the time necessary to
perform the specific actions actually required by the AD. These figures
typically do not include incidental costs, such as the time required to
gain access and close up, planning time, or time necessitated by other
administrative actions.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, Section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701, ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Impact
The regulations adopted herein will not have a substantial direct
effect on the States, on the relationship between the national
Government and the States, or on the distribution of power and
responsibilities among the various levels of government. Therefore, it
is determined that this final rule does not have federalism
implications under Executive Order 13132.
For the reasons discussed above, I certify that this action (1) Is
not a ``significant regulatory action'' under Executive Order 12866;
(2) is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979); and (3) will not have a
significant economic impact, positive or negative, on a substantial
number of small entities under the criteria of the Regulatory
Flexibility Act. A final evaluation has been prepared for this action
and it is contained in the Rules Docket. A copy of it may be obtained
from the Rules Docket at the location provided under the caption
ADDRESSES.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
0
Accordingly, pursuant to the authority delegated to me by the
Administrator, the Federal Aviation Administration amends part 39 of
the Federal Aviation Regulations (14 CFR part 39) as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. Section 39.13 is amended by adding the following new airworthiness
directive:
2009-20-02 Boeing: Amendment 39-16025. Docket No. FAA-2008-0682;
Directorate Identifier 2001-NM-237-AD.
Applicability: Model 767-200 and -300 series airplanes, line
numbers 1 through 793 inclusive; certificated in any category;
equipped with door-mounted escape slide systems; as identified in
Boeing Service Bulletin 767-25A0266, Revision 3, dated July 3, 2008.
Compliance: Required as indicated, unless accomplished
previously.
To prevent the escape slides and slide-rafts of the forward and
mid-cabin entry and service doors from being too steep for
evacuation in the event that the airplane rotates onto the aft
fuselage into the extreme tip-back condition, accomplish the
following:
Replacement of Slide-Rafts
(a) Within 96 months after the effective date of this AD,
replace the applicable slide-rafts at the applicable door or doors,
and do all other applicable actions including, but not limited to,
changing the latches, and replacing or modifying the counterbalance
assemblies, by accomplishing all applicable actions specified in the
Accomplishment Instructions in Boeing Service Bulletin 767-25A0266,
Revision 3, dated July 3, 2008.
Credit for Actions Accomplished Previously
(b) Actions done before the effective date of this AD in
accordance with the service bulletins listed in Table 1 of this AD
are
[[Page 49801]]
acceptable for compliance with the corresponding requirements of
this AD.
------------------------------------------------------------------------
Boeing Service Bulletin Revision level Date
------------------------------------------------------------------------
Alert Service Bulletin 767- 1 December 4, 2006.
25A0266.
Alert Service Bulletin 767- 2 September 27, 2007.
25A0266.
------------------------------------------------------------------------
Alternative Methods of Compliance
(c)(1) The Manager, Seattle Aircraft Certification Office, FAA,
has the authority to approve AMOCs for this AD, if requested using
the procedures found in 14 CFR 39.19. Send information to ATTN:
Andrew Guion, Aerospace Engineer, Cabin Safety and Environmental
Systems Branch, ANM-150S, FAA, Seattle Aircraft Certification
Office, 1601 Lind Avenue, SW., Renton, Washington 98057-3356;
telephone (425) 917-6428; fax (425) 917-6590. Or, e-mail information
to <a href="/cdn-cgi/l/email-protection#40796d010e0d6d13252134342c256d01030f6d010d0f036d1225313525333433002621216e272f36"><span class="__cf_email__" data-cfemail="10293d515e5d3d43757164647c753d51535f3d515d5f533d4275616575636463507671713e777f66">[email protected]</span></a>.
(2) To request a different method of compliance or a different
compliance time for this AD, follow the procedures in 14 CFR 39.19.
Before using any approved AMOC on any airplane to which the AMOC
applies, notify your principal maintenance inspector (PMI) or
principal avionics inspector (PAI), as appropriate, or lacking a
principal inspector, your local Flight Standards District Office.
The AMOC approval letter must specifically reference this AD.
Incorporation by Reference
(d) You must use Boeing Service Bulletin 767-25A0266, Revision
3, dated July 3, 2008, to do the actions required by this AD, unless
the AD specifies otherwise.
(1) The Director of the Federal Register approved the
incorporation by reference of this service information under 5
U.S.C. 552(a) and 1 CFR part 51.
(2) For service information identified in this AD, contact
Boeing Commercial Airplanes, Attention: Data & Services Management,
P.O. Box 3707, MC 2H-65, Seattle, Washington 98124-2207; telephone
206-544-5000, extension 1; fax 206-766-5680; e-mail
<a href="/cdn-cgi/l/email-protection#b2dfd79cd0ddd7d1dddff2d0ddd7dbdcd59cd1dddf"><span class="__cf_email__" data-cfemail="563b337834393335393b163439333f38317835393b">[email protected]</span></a>; Internet <a href="https://www.myboeingfleet.com">https://www.myboeingfleet.com</a>.
(3) You may review copies of the service information at the FAA,
Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton,
Washington. For information on the availability of this material at
the FAA, call 425-227-1221 or 425-227-1152.
(4) You may also review copies of the service information that
is incorporated by reference at the National Archives and Records
Administration (NARA). For information on the availability of this
material at NARA, call 202-741-6030, or go to: <a href="http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html">http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html</a>.
Effective Date
(e) This amendment becomes effective on November 3, 2009.
Issued in Renton, Washington, on September 11, 2009.
Stephen P. Boyd,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. E9-22668 Filed 9-28-09; 8:45 am]
BILLING CODE 4910-13-P
Source: Official FAA Source ↗
Retrieved: Apr 4, 2026
Rights: U.S. Government Public Domain
This site is not affiliated with or endorsed by the FAA. Always verify with official sources.