AD 2007-17-10
Applicability
| Type | Manufacturer | Model | Details |
|---|---|---|---|
| aircraft | Embraer S.A. | EMB-135BJ (Legacy 600) | Airworthiness Directives; Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-135BJ Airplanes |
Unsafe Condition
The drain mast of the water and waste system does not meet the SFAR-88 requirements. In case of fuel leakage or fuel vapor release, the proximity of this mast with the fuel tank may cause fuel ignition, leading to a possible tank explosion.
AI-generated summary from the source AD text. Verify against the official source before acting.
Required Actions
Replace the water and waste system drain masts with P/N 9402.369.00674 by new ones bearing a P/N 9402.369.00675, according to the detailed instructions and procedures described in EMBRAER Service Bulletin 145LEG-38-0013. Alternatively, the accomplishment of the detailed instructions and procedures described in EMBRAER Service Bulletin 145LEG-38-0015 or 145LEG-38-0020 is acceptable for compliance.
AI-generated summary from the source AD text. Verify against the official source before acting.
Compliance Time
Within 5,000 flight hours or 4 years after the effective date of this AD, whichever occurs first.
AI-generated summary from the source AD text. Verify against the official source before acting.
Affected Aircraft
EMBRAER Model EMB-135BJ airplanes, as identified in EMBRAER Service Bulletin 145LEG-38-0013, dated March 24, 2006, certificated in any category; except those that have previously accomplished EMBRAER Service Bulletin 145LEG-38-0015 or 145LEG-38-0020.
AI-generated summary from the source AD text. Verify against the official source before acting.
Federal Register Abstract
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Document Text
Show stored source text (verify against official source)
[Federal Register Volume 72, Number 166 (Tuesday, August 28, 2007)]
[Rules and Regulations]
[Pages 49173-49175]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: E7-16427]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2007-28158; Directorate Identifier 2007-NM-018-AD;
Amendment 39-15168; AD 2007-17-10]
RIN 2120-AA64
Airworthiness Directives; Empresa Brasileira de Aeronautica S.A.
(EMBRAER) Model EMB-135BJ Airplanes
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: We are adopting a new airworthiness directive (AD) for the
products listed above. This AD results from mandatory continuing
airworthiness information (MCAI) originated by an aviation authority of
another country to identify and correct an unsafe condition on an
aviation product. The MCAI describes the unsafe condition as:
It has been found cases in which the drain mast of the water and
waste system does not meet the SFAR-88 (Special Federal Aviation
Regulation No. 88) requirements. In case of fuel leakage or fuel
vapor release, the proximity of this mast with the fuel tank may
cause fuel ignition, leading to a possible tank explosion.
We are issuing this AD to require actions to correct the unsafe
condition on these products.
DATES: This AD becomes effective October 2, 2007.
The Director of the Federal Register approved the incorporation by
reference of certain publications listed in this AD as of October 2,
2007.
ADDRESSES: You may examine the AD docket on the Internet at <a href="http://dms.dot.gov">http://dms.dot.gov</a> or in person at the U.S. Department of Transportation,
Docket Operations, M-30, West Building, Ground Floor, Room W12-140,
1200 New Jersey Avenue, SE., Washington, DC.
FOR FURTHER INFORMATION CONTACT: Todd Thompson, Aerospace Engineer,
International Branch, ANM-116, FAA, Transport Airplane Directorate,
1601
[[Page 49174]]
Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 227-
1175; fax (425) 227-1149.
SUPPLEMENTARY INFORMATION:
Discussion
We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR
part 39 to include an AD that would apply to the specified products.
That NPRM was published in the Federal Register on May 16, 2007 (72 FR
27491). That NPRM proposed to correct an unsafe condition for the
specified products. The MCAI states:
It has been found cases in which the drain mast of the water and
waste system does not meet the SFAR-88 (Special Federal Aviation
Regulation No. 88) requirements. In case of fuel leakage or fuel
vapor release, the proximity of this mast with the fuel tank may
cause fuel ignition, leading to a possible tank explosion.
The MCAI requires replacement of the water and waste system drain masts
by new ones bearing a new part number (P/N). You may obtain further
information by examining the MCAI in the AD docket.
Comments
We gave the public the opportunity to participate in developing
this AD. We considered the comment received.
Request To Revise Applicability Statement
The airplane manufacturer, EMBRAER, requests that we change the
proposed applicability statement from ``This AD applies to EMBRAER
Model EMB-135BJ airplanes, certificated in any category; except those
that have previously accomplished EMBRAER Service Bulletin 145LEG-38-
0015 or 145LEG-38-0020'' to ``This AD applies to EMBRAER Model EMB-
135BJ airplanes, certificated in any category as listed in Embraer
Service Bulletin 145LEG-38-0013, original issue, dated 24/Mar/2006;
except those that have previously accomplished EMBRAER Service Bulletin
145LEG-38-0015 or 145LEG-38-0020.'' We infer that the manufacturer
wants us to restrict our applicability statement to those airplanes
with an affected drain mast installed.
We agree to revise the applicability statement of this AD. The
service bulletin identifies only those airplanes that have an affected
drain mast installed. We have revised paragraph (c) of this AD to
clarify which airplanes are affected by this AD. We have coordinated
this change with Ag[ecirc]ncia Nacional de Avia[ccedil][atilde]o Civil
(ANAC).
Conclusion
We reviewed the available data, including the comment received, and
determined that air safety and the public interest require adopting the
AD with the change described previously. We determined that this change
will not increase the economic burden on any operator or increase the
scope of the AD.
Differences Between This AD and the MCAI or Service Information
We have reviewed the MCAI and related service information and, in
general, agree with their substance. But we might have found it
necessary to use different words from those in the MCAI to ensure the
AD is clear for U.S. operators and is enforceable. In making these
changes, we do not intend to differ substantively from the information
provided in the MCAI and related service information.
We might also have required different actions in this AD from those
in the MCAI in order to follow our FAA policies. Any such differences
are highlighted in a NOTE within the AD.
Costs of Compliance
We estimate that this AD will affect 41 products of U.S. registry.
We also estimate that it will take about 20 work-hours per product to
comply with the basic requirements of this AD. The average labor rate
is $80 per work-hour. Required parts will cost about $9,633 per
product. Where the service information lists required parts costs that
are covered under warranty, we have assumed that there will be no
charge for these parts. As we do not control warranty coverage for
affected parties, some parties may incur costs higher than estimated
here. Based on these figures, we estimate the cost of this AD to the
U.S. operators to be $460,553, or $11,233 per product.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. ``Subtitle VII: Aviation
Programs,'' describes in more detail the scope of the Agency's
authority.
We are issuing this rulemaking under the authority described in
``Subtitle VII, Part A, Subpart III, Section 44701: General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We determined that this AD will not have federalism implications
under Executive Order 13132. This AD will not have a substantial direct
effect on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government.
For the reasons discussed above, I certify this AD:
1. Is not a ``significant regulatory action'' under Executive Order
12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this AD and placed it in the AD docket.
Examining the AD Docket
You may examine the AD docket on the Internet at <a href="http://dms.dot.gov">http://dms.dot.gov</a>; or in person at the Docket Operations office between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD
docket contains the NPRM, the regulatory evaluation, any comments
received, and other information. The street address for the Docket
Operations office (telephone (800) 647-5527) is in the ADDRESSES
section. Comments will be available in the AD docket shortly after
receipt.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
0
Accordingly, under the authority delegated to me by the Administrator,
the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new AD:
2007-17-10 Empresa Brasileira de Aeronautica S.A. (EMBRAER):
[[Page 49175]]
Amendment 39-15168. Docket No. FAA-2007-28158; Directorate
Identifier 2007-NM-018-AD.
Effective Date
(a) This airworthiness directive (AD) becomes effective October
2, 2007.
Affected ADs
(b) None.
Applicability
(c) This AD applies to EMBRAER Model EMB-135BJ airplanes, as
identified in EMBRAER Service Bulletin 145LEG-38-0013, dated March
24, 2006, certificated in any category; except those that have
previously accomplished EMBRAER Service Bulletin 145LEG-38-0015 or
145LEG-38-0020.
Subject
(d) Air Transport Association (ATA) of America Code 38: Water/
Waste.
Reason
(e) The mandatory continuing airworthiness information (MCAI)
states:
It has been found cases in which the drain mast of the water and
waste system does not meet the SFAR-88 (Special Federal Aviation
Regulation No. 88) requirements. In case of fuel leakage or fuel
vapor release, the proximity of this mast with the fuel tank may
cause fuel ignition, leading to a possible tank explosion.
The MCAI requires replacement of the water and waste system drain
masts by new ones bearing a new part number (P/N).
Actions and Compliance
(f) Unless already done, do the following actions.
(1) Within 5,000 flight hours or 4 years after the effective
date of this AD, whichever occurs first, replace the water and waste
system drain masts with P/N 9402.369.00674 by new ones bearing a P/N
9402.369.00675, according to the detailed instructions and
procedures described in EMBRAER Service Bulletin 145LEG-38-0013,
dated March 24, 2006.
(2) The accomplishment of the detailed instructions and
procedures described in EMBRAER Service Bulletin 145LEG-38-0015,
dated November 25, 2005; or 145LEG-38-0020, dated February 3, 2006;
are acceptable for compliance with the requirements of this AD.
FAA AD Differences
Note: This AD differs from the MCAI and/or service information
as follows: No differences.
Other FAA AD Provisions
(g) The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager,
International Branch, ANM-116, Transport Airplane Directorate, FAA,
has the authority to approve AMOCs for this AD, if requested using
the procedures found in 14 CFR 39.19. Send information to ATTN: Todd
Thompson, Aerospace Engineer, International Branch, ANM-116,
Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton,
Washington 98057-3356; telephone (425) 227-1175; fax (425) 227-1149.
Before using any approved AMOC on any airplane to which the AMOC
applies, notify your appropriate principal inspector (PI) in the FAA
Flight Standards District Office (FSDO), or lacking a PI, your local
FSDO.
(2) Airworthy Product: For any requirement in this AD to obtain
corrective actions from a manufacturer or other source, use these
actions if they are FAA-approved. Corrective actions are considered
FAA-approved if they are approved by the State of Design Authority
(or their delegated agent). You are required to assure the product
is airworthy before it is returned to service.
(3) Reporting Requirements: For any reporting requirement in
this AD, under the provisions of the Paperwork Reduction Act, the
Office of Management and Budget (OMB) has approved the information
collection requirements and has assigned OMB Control Number 2120-
0056.
Related Information
(h) Refer to MCAI Brazilian Airworthiness Directive 2007-01-04,
effective January 29, 2007, and the service bulletins listed in
Table 1 of this AD, for related information.
Table 1.--Sources of Related Information
------------------------------------------------------------------------
Revision
EMBRAER Service Bulletin-- level-- Dated--
------------------------------------------------------------------------
145LEG-38-0005............... 02........... November 20, 2003.
145LEG-38-0013............... Original..... March 24, 2006.
145LEG-38-0015............... Original..... November 25, 2005.
145LEG-38-0020............... Original..... February 3, 2006.
------------------------------------------------------------------------
Material Incorporated by Reference
(i) You must use EMBRAER Service Bulletin 145LEG-38-0013, dated
March 24, 2006; and EMBRAER Service Bulletin 145LEG-38-0005,
Revision 02, dated November 20, 2003; as applicable; to do the
actions required by this AD, unless the AD specifies otherwise.
(1) The Director of the Federal Register approved the
incorporation by reference of this service information under 5
U.S.C. 552(a) and 1 CFR part 51.
(2) For service information identified in this AD, contact
Empresa Brasileira de Aeronautica S.A. (EMBRAER), P.O. Box 343--CEP
12.225, Sao Jose dos Campos--SP, Brazil.
(3) You may review copies at the FAA, Transport Airplane
Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the
National Archives and Records Administration (NARA). For information
on the availability of this material at NARA, call (202) 741-6030,
or go to: <a href="http://www.archives.gov/federal-register/cfr/ibr-locations.html">http://www.archives.gov/federal-register/cfr/ibr-locations.html</a>.
Issued in Renton, Washington, on August 14, 2007.
Stephen P. Boyd,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. E7-16427 Filed 8-27-07; 8:45 am]
BILLING CODE 4910-13-P
Source: Official FAA Source ↗
Retrieved: Apr 4, 2026
Rights: U.S. Government Public Domain
This site is not affiliated with or endorsed by the FAA. Always verify with official sources.