AD 2005-13-31

[Federal Register Volume 70, Number 123 (Tuesday, June 28, 2005)]
[Rules and Regulations]
[Pages 37020-37022]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 05-12508]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. 2003-NM-127-AD; Amendment 39-14168; AD 2005-13-31]
RIN 2120-AA64


Airworthiness Directives; Short Brothers Model SD3-60 Airplanes

AGENCY: Federal Aviation Administration, Department of Transportation.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: This amendment adopts a new airworthiness directive (AD), 
applicable to all Short Brothers Model SD3-60 airplanes, that requires 
performing repetitive inspections of the shear attachment fittings of 
the vertical stabilizer for corrosion, and performing corrective 
actions if necessary. The actions specified by this AD are intended to 
detect and correct corrosion in the area of the main spar web fittings 
of the vertical stabilizer, which could

[[Page 37021]]

result in reduced structural integrity of the vertical stabilizer. This 
action is intended to address the identified unsafe condition.

DATES: Effective August 2, 2005.
    The incorporation by reference of a certain publication listed in 
the regulations is approved by the Director of the Federal Register as 
of August 2, 2005.

ADDRESSES: The service information referenced in this AD may be 
obtained from Short Brothers, Airworthiness & Engineering Quality, P.O. 
Box 241, Airport Road, Belfast BT3 9DZ, Northern Ireland. This 
information may be examined at the Federal Aviation Administration 
(FAA), Transport Airplane Directorate, Rules Docket, 1601 Lind Avenue, 
SW., Renton, Washington.

FOR FURTHER INFORMATION CONTACT: Todd Thompson, Aerospace Engineer, 
International Branch, ANM-116, FAA, Transport Airplane Directorate, 
1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425) 
227-1175; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION: A proposal to amend part 39 of the Federal 
Aviation Regulations (14 CFR part 39) to include an airworthiness 
directive (AD) that is applicable to all Short Brothers Model SD3-60 
airplanes was published as a supplemental notice of proposed rulemaking 
(NPRM) in the Federal Register on April 1, 2005 (70 FR 16764). That 
action proposed to require performing repetitive inspections of the 
shear attachment fittings of the vertical stabilizer for corrosion, and 
performing corrective actions if necessary. The actions specified by 
this AD are intended to detect and correct corrosion in the area of the 
main spar web fittings of the vertical stabilizer, which could result 
in reduced structural integrity of the vertical stabilizer.

Comments

    We provided the public the opportunity to participate in the 
development of this AD. No comments have been submitted on the proposed 
AD or on the determination of the cost to the public.

Explanation of Change to Applicability

    We have revised the applicability of the proposed AD to identify 
model designations as published in the most recent type certificate 
data sheet for the affected models.

Explanation of Change to Final Rule

    The proposed AD had an incorrectly numbered ``Note'' paragraph. We 
have corrected the number of that Note in the final rule.

Conclusion

    We have carefully reviewed the available data and determined that 
air safety and the public interest require adopting the AD with the 
changes described previously. We have determined that these changes 
will neither increase the economic burden on any operator nor increase 
the scope of the AD.

Cost Impact

    The following table provides the estimated costs for U.S. operators 
to comply with this AD.

                                                                                         Estimated Costs
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
                                                                                                                           Number of U.S.-
                 Action                      Work hours     Average labor               Parts                 Cost per        registered                         Fleet cost
                                                            rate per hour                                     airplane        airplanes
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Inspection, per inspection cycle........               4              $65   None........................            $260               46   $11,960, per inspection cycle.
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

    The cost impact figure discussed above is based on assumptions that 
no operator has yet accomplished any of the requirements of this AD 
action, and that no operator would accomplish those actions in the 
future if this AD were not adopted. The cost impact figures discussed 
in AD rulemaking actions represent only the time necessary to perform 
the specific actions actually required by the AD. These figures 
typically do not include incidental costs, such as the time required to 
gain access and close up, planning time, or time necessitated by other 
administrative actions.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, Section 106, describes the 
authority of the FAA Administrator. Subtitle VII, Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701, ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Impact

    The regulations adopted herein will not have a substantial direct 
effect on the States, on the relationship between the National 
Government and the States, or on the distribution of power and 
responsibilities among the various levels of government. Therefore, it 
is determined that this final rule does not have federalism 
implications under Executive Order 13132.
    For the reasons discussed above, I certify that this action (1) is 
not a ``significant regulatory action'' under Executive Order 12866; 
(2) is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979); and (3) will not have a 
significant economic impact, positive or negative, on a substantial 
number of small entities under the criteria of the Regulatory 
Flexibility Act. A final evaluation has been prepared for this action 
and it is contained in the Rules Docket. A copy of it may be obtained 
from the Rules Docket at the location provided under the caption 
ADDRESSES.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

0
Accordingly, pursuant to the authority delegated to me by the 
Administrator, the Federal Aviation Administration amends part 39 of 
the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:


[[Page 37022]]


    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. Section 39.13 is amended by adding the following new airworthiness 
directive:

2005-13-31 Short Brothers PLC: Amendment 39-14168. Docket 2003-NM-
127-AD.

    Applicability: All Model SD3-60 airplanes, certificated in any 
category.
    Compliance: Required as indicated, unless accomplished 
previously.
    To detect and correct corrosion in the area of the main spar web 
fittings of the vertical stabilizer, which could result in reduced 
structural integrity of the vertical stabilizer, accomplish the 
following:

Inspection and Previous Actions

    (a) Except as provided by paragraphs (a)(1) and (a)(2) of this 
AD, within 4,800 flight hours or 90 days after the effective date of 
this AD, whichever occurs first, do a borescope inspection to detect 
corrosion of the shear attachment fittings of the vertical 
stabilizer, in accordance with the Accomplishment Instructions of 
Short Brothers Service Bulletin SD360-53-45, dated December 2003.
    (1) If an airplane (the shear attachment fitting) has been 
inspected in accordance with the Accomplishment Instructions of 
Short Brothers Service Bulletin SD360-53-44, Revision 1, dated 
January 24, 2003, before the effective date of this AD, and was 
found to have no corrosion on the fittings, then the initial 
inspection specified in paragraph (a) of this AD is not required.
    (2) If the shear attachment fitting has been inspected in 
accordance with the Accomplishment Instructions of Short Brothers 
Service Bulletin SD360-53-44, Revision 1, dated January 24, 2003, 
and was found to have corrosion, but the corroded fitting is not yet 
replaced, then a review of the inspection results is required to 
determine if the corrosion was within the acceptable limits 
specified in Short Brothers Service Bulletin SD360-53-45, dated 
December 2003.

Corrective Actions and Repetitive Inspections

    (b) If any corrosion is found during the inspection required by 
paragraph (a) of this AD, do the applicable actions required by 
paragraph (b)(1) or (b)(2) of this AD.
    (1) If any corrosion is within the limits specified in the 
Accomplishment Instructions of Short Brothers Service Bulletin 
SD360-53-45, dated December 2003, do the actions required by 
paragraphs (b)(1)(i) and (b)(1)(ii) of this AD.
    (i) Repeat the inspection required by the service bulletin at 
intervals not to exceed 6 months.
    (ii) Within 18 months after the initial inspection required by 
paragraph (a) of this AD, replace all corroded shear attachment 
fittings in accordance with the Accomplishment Instructions of the 
service bulletin. Accomplishing the replacement ends the repetitive 
inspections required by paragraph (b)(1)(i) of this AD.
    (2) If any corrosion is outside the limits specified in the 
Accomplishment Instructions of Short Brothers Service Bulletin 
SD360-53-45, dated December 2003, before further flight, replace the 
corroded fitting with a new fitting, in accordance with the 
Accomplishment Instructions of the service bulletin.
    (c) If no corrosion is found during the inspection required by 
paragraph (a) or if the fitting was replaced with a new fitting in 
accordance with Short Brothers Service Bulletin SD360-53-45, dated 
December 2003, do the actions in paragraphs (c)(1) and (c)(2) of 
this AD.
    (1) Within 24 months after the initial inspection required by 
paragraph (a) of this AD or within 24 months after replacement of 
the fitting with a new one, whichever occurs later, do a borescope 
(intrascope) detailed inspection for corrosion, in accordance with 
Part A of the Accomplishment Instructions of Short Brothers Service 
Bulletin SD360-53-45, dated December 2003. Repeat this inspection 
thereafter at intervals not to exceed 24 months. Do corrective 
actions in accordance with paragraph (b) of this AD.
    (2) Thereafter, except as provided in paragraph (f) of this AD, 
no alternative borescope inspections may be approved.

Previous Repetitive Inspections

    (d) Borescope (intrascope) detailed inspections done before the 
effective date of this AD in accordance with Bombardier Temporary 
Revisions (TR) TR360-MPSUPP-04 and TR360-MPSUPP-03, both dated 
August 20, 2003, are acceptable for compliance with the requirements 
of paragraph (c)(1) of this AD.

Disposition of Repairs for Corroded/Oversized Holes

    (e) Where Short Brothers Service Bulletin SD360-53-45, dated 
December 2003, says to contact the manufacturer for action on any 
corroded or oversized hole found during the inspection required by 
paragraph (a) or (c) of this AD, before further flight, repair in 
accordance with a method approved by either the Manager, 
International Branch, ANM-116, FAA, Transport Airplane Directorate; 
or the Civil Aviation Authority (or its delegated agent).

Alternative Methods of Compliance

    (f) In accordance with 14 CFR 39.19, the Manager, International 
Branch, ANM-116, is authorized to approve alternative methods of 
compliance for this AD.

    Note 1: The subject of this AD is addressed in British 
airworthiness directive G-2004-0005, effective March 16, 2004.

Incorporation by Reference

    (g) You must use Short Brothers Service Bulletin SD360-53-45, 
dated December 2003, to perform the actions that are required by 
this AD, unless the AD specifies otherwise. The Director of the 
Federal Register approves the incorporation by reference of this 
document in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. To 
get copies of the service information, contact Short Brothers, 
Airworthiness & Engineering Quality, P.O. Box 241, Airport Road, 
Belfast BT3 9DZ, Northern Ireland. To inspect copies of this service 
information, go to the FAA, Transport Airplane Directorate, 1601 
Lind Avenue, SW., Renton, Washington; or to the National Archives 
and Records Administration (NARA). For information on the 
availability of this material at the NARA, call (202) 741-6030, or 
go to <a href="http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html">http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html</a>.

Effective Date

    (h) This amendment becomes effective on August 2, 2005.

    Issued in Renton, Washington, on June 14, 2005.
Kevin M. Mullin,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 05-12508 Filed 6-27-05; 8:45 am]
BILLING CODE 4910-13-P